DTC P2195 Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
DTC P2196 Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2195 | Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):
|
|
| While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current is 2.2 mA or more for 3 seconds (2 trip detection logic). |
| |
| P2196 | Conditions (a) and (b) continue for 5 seconds or more (2 trip detection logic):
|
|
| While fuel-cut operation performed (during vehicle deceleration), air fuel ratio sensor current is less than 0.7 mA for 3 seconds (2 trip detection logic). |
|

| Related DTCs | P2195: Air Fuel Ratio Sensor (Bank 1 Sensor 1) Signal Stuck Lean P2196: Air Fuel Ratio Sensor (Bank 1 Sensor 1) Signal Stuck Rich |
| Required Sensors/Components (Main) | Air fuel ratio sensor |
| Required Sensors/Components (Related) | Heated oxygen sensor |
| Frequency of Operation | Continuous: Sensor voltage detection monitor Once per driving cycle: Sensor current detection monitor |
| Duration | 5 seconds: Sensor voltage detection monitor 3 seconds: Sensor current detection monitor |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0016 (VVT System - Misalignment) P0031, P0032, P101D (Air Fuel Ratio Sensor Heater) P0102, P0103 (Mass Air Flow Sensor) P0112, P0113 (Intake Air Temperature Sensor) P0115, P0117, P0118 (Engine Coolant Temperature Sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor) P0128 (Thermostat) P0171, P0172 (Fuel System) P0301 - P0304 (Misfire) P0335 (Crankshaft Position Sensor) P0340 (Camshaft Position Sensor) P0451, P0452, P0453 (EVAP System) P0500 (Vehicle Speed Sensor) P0505 (IAC Valve) P219A (Air Fuel Ratio Imbalance) |
| Time after engine start | 30 seconds or more |
| Fuel system status | Closed loop |
| Air fuel ratio sensor status | Activated |
| Battery voltage | 11 V or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Air fuel ratio sensor status | Activated |
| Engine coolant temperature | 75°C (167°F) or higher |
| Continuous time of fuel cut | 3 seconds or more, and less than 10 seconds |
| Rear heated oxygen sensor voltage | 0.21 V or higher |
| Air fuel ratio sensor voltage | Higher than 3.8 V |
| Rear heated oxygen sensor voltage | Below 0.69 V |
| Air fuel ratio sensor voltage | Below 2.8 V |
| Air fuel ratio sensor current | 2.2 mA or higher |
| Air fuel ratio sensor current | Below 0.7 mA |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $01 | $91 | Multiply by 0.004 | mA | A/F sensor current |


| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195 OR P2196) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P2195 or P2196 is output | A |
| DTC P2195 or P2196 and P0136, P0137 or P0138 are output | |
| DTC P2195 or P2196 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?
|
| ||||
| YES | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2195 or P2196 is output) | B |
|
| ||||
| A | ||
| ||
| 4.READ VALUE USING TECHSTREAM (TEST VALUE OF AIR FUEL RATIO SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Current.
Check that the status of O2 Sensor is Complete.
If the status is still Incomplete, drive the vehicle according to the driving pattern again.
Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details / RANGE B1S1.
Check the test value of the air fuel ratio sensor output current during fuel-cut.
| Result | Proceed to |
| Within normal range (0.7 mA or higher, and lower than 2.2 mA) | A |
| Outside normal range (lower than 0.7 mA, or 2.2 mA or higher) | B |
|
| ||||
| A | |
| 5.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Perform the Control the Injection Volume operation with the engine idling.
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the Techstream.
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | +12% | Rich | Below 3.1 V |
| AFS Voltage B1S1 (Air fuel ratio) | -12% | Lean | Higher than 3.4 V |
| O2S B1S2 (Heated oxygen) | +12% | Rich | Higher than 0.55 V |
| O2S B1S2 (Heated oxygen) | -12% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 | Status of O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
| Lean | Lean | Actual air fuel ratio lean | A |
| Rich | Rich | Actual air fuel ratio rich | A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Lean/Rich | Lean/Rich | Normal | B |
|
| ||||
| A | |
| 6.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 7.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 8.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 9.INSPECT FUEL INJECTOR ASSEMBLY |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 10.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment.
| Result | Proceed to |
| ABNORMAL (DTC P2195 or P2196 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 12.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment.
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2195 or P2196.
Check the DTC judgment.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2195 or P2196 is output) | B |
|
| ||||
| A | ||
| ||
| 16.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||