Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › 2013.08–2016.04
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0086991 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Blower Motor Circuit  


DESCRIPTION

When the heater control and accessory assembly is operated, the heater relay will turn on to allow current to flow to the blower motor and then the motor will start rotating. Operating the heater control and accessory assembly switches the current flow between the blower resistor and body ground, thus, shifting the rotation speed of the blower motor with fan sub-assembly.

WIRING DIAGRAM

E279825E01
1.01,3.458 1.563,3.615 0.552,0.156 10 false 4*3, 1*4 1.01,5.885 1.563,6.042 0.552,0.156 10 false 1*3, 4*4 1.833,4.729 2.5,4.885 0.667,0.156 10 false 2*3, 3*4 1.833,5.167 2.5,5.323 0.667,0.156 10 false 3*3, 2*4 0.167,8.021 3.396,8.219 3.229,0.198 10 false *1: w/o Smart Entry and Start System 4.188,3.563 4.854,3.719 0.667,0.156 10 false 6*3, 10*4 5.865,6.531 6.531,6.688 0.667,0.156 10 false 10*3, 6*4 0.167,8.396 3.396,8.594 3.229,0.198 10 false *2: w/ Smart Entry and Start System 3.146,6.75 6.375,6.948 3.229,0.198 10 false Heater Control and Accessory Assembly 3.146,6.594 3.417,6.75 0.271,0.156 10 false F5 0.219,4.635 0.531,4.792 0.313,0.156 10 false F55 0.208,4.792 1.281,5.01 1.073,0.219 10 false Blower Resistor 1.563,4.729 1.802,4.885 0.24,0.156 10 false M2 1.563,5.177 1.802,5.333 0.24,0.156 10 false M1 1.344,5.667 1.583,5.823 0.24,0.156 10 false E 1.333,3.667 1.573,3.823 0.24,0.156 10 false HI 6.323,6.333 6.563,6.531 0.24,0.198 10 false E 3.302,6.177 4.375,6.396 1.073,0.219 10 false Blower Switch 3.854,3.771 4.094,3.927 0.24,0.156 10 false HI 4.542,3.771 4.781,3.927 0.24,0.156 10 false M2 5.115,3.771 5.354,3.927 0.24,0.156 10 false M1 5.677,3.76 5.917,3.917 0.24,0.156 10 false LO 4.135,4.188 4.375,4.344 0.24,0.156 10 false HI 4.677,4.188 4.917,4.344 0.24,0.156 10 false M2 5.24,4.198 5.479,4.354 0.24,0.156 10 false M1 5.802,4.198 6.042,4.354 0.24,0.156 10 false LO 6.427,4.188 6.667,4.344 0.24,0.156 10 false E 3.552,4.417 3.792,4.573 0.24,0.156 10 false 0 3.552,4.635 3.792,4.792 0.24,0.156 10 false 1 3.458,4.844 3.896,5.01 0.438,0.167 10 false 1 - 2 3.552,5.063 3.792,5.219 0.24,0.156 10 false 2 3.458,5.292 3.854,5.49 0.396,0.198 10 false 2 - 3 3.542,5.521 3.781,5.677 0.24,0.156 10 false 3 3.458,5.74 3.854,5.938 0.396,0.198 10 false 3 - 4 3.552,5.948 3.792,6.104 0.24,0.156 10 false 4 3.646,0.26 3.885,0.417 0.24,0.156 10 false 1 2.885,0.271 3.125,0.427 0.24,0.156 10 false 2 3.646,0.99 3.885,1.146 0.24,0.156 10 false 3 2.875,1 3.115,1.156 0.24,0.156 10 false 5 2.948,1.417 3.26,1.573 0.313,0.156 10 false F78 2.948,1.594 4.125,1.792 1.177,0.198 10 false Heater Relay 2.698,1.99 3.01,2.146 0.313,0.156 10 false F53 2.698,2.167 3.865,2.531 1.167,0.365 10 false Blower Motor with Fan Sub-assembly 4.083,1.781 4.323,1.938 0.24,0.156 10 false 2 4.073,2.406 4.323,2.563 0.25,0.156 10 false 1 5.219,3.563 5.469,3.719 0.25,0.156 10 false 1 5.781,3.563 6.01,3.729 0.229,0.167 10 false 3 3.927,3.563 4.167,3.719 0.24,0.156 10 false 5 1.958,0.531 2.927,0.708 0.969,0.177 10 false ECU-IG NO. 1 2.198,1.25 2.667,1.469 0.469,0.219 10 false HTR 0.76,1.073 1.938,1.271 1.177,0.198 10 false from Battery 0.229,0.208 1.688,0.844 1.458,0.635 10 false from Ignition or Starter Switch Assembly*1 or No. 1 Ignition Relay*2 2.667,8.021 5.896,8.219 3.229,0.198 10 false *3: for LHD 2.677,8.396 5.906,8.594 3.229,0.198 10 false *4: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT HEATER RELAY
a.

Remove the heater relay.



Result:
Proceed to
OK
NG



OK

2.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPLACE HEATER RELAY

2.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY
a.

Remove the blower motor with fan sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>REMOVAL


b.

Inspect the blower motor with fan sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>FRONT BLOWER MOTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT BLOWER RESISTOR

NG

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

3.INSPECT BLOWER RESISTOR


Result:
Proceed to
OK
NG



OK

4.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (BLOWER SWITCH)

NG

4.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (BLOWER SWITCH)


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (HEATER RELAY - POWER SOURCE)

NG

5.CHECK HARNESS AND CONNECTOR (HEATER RELAY - POWER SOURCE)
a.
E281479C04
0.333,0.771 0.76,1.01 0.427,0.24 0.427,0.781 0.885,0.979 0.458,0.198 10 false F78 0.115,0.104 0.573,0.302 0.458,0.198 10 false *1
*1 Heater Relay Holder


Remove the heater relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F78-2 - Body ground Ignition switch off Below 1 V
F78-2 - Body ground Ignition switch ON 11 to 14 V
F78-5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HEATER RELAY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HEATER RELAY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
a.

Remove the heater relay.


b.

Disconnect the F53 blower motor with fan sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-3 - F53-2 Always Below 1 Ω
F78-3 or F53-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BLOWER RESISTOR - BLOWER MOTOR WITH FAN SUB-ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (BLOWER RESISTOR - BLOWER MOTOR WITH FAN SUB-ASSEMBLY AND BODY GROUND)
a.

Disconnect the F55 blower resistor connector.


b.

Disconnect the F53 blower motor with fan sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F55-4 (HI) - F53-1 Always Below 1 Ω
F55-1 (E) - Body ground Always Below 1 Ω
F55-4 (HI) or F53-1 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F55-1 (HI) - F53-1 Always Below 1 Ω
F55-4 (E) - Body ground Always Below 1 Ω
F55-1 (HI) or F53-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER CONTROL AND ACCESSORY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER CONTROL AND ACCESSORY ASSEMBLY)
a.

Disconnect the F53 blower motor with fan sub-assembly connector.


b.

Disconnect the F5 heater control and accessory assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F53-1 - F5-5 (HI) Always Below 1 Ω
F53-1 or F5-5 (HI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HEATER CONTROL AND ACCESSORY ASSEMBLY - BLOWER RESISTOR AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (HEATER CONTROL AND ACCESSORY ASSEMBLY - BLOWER RESISTOR AND BODY GROUND)
a.

Disconnect the F5 heater control and accessory assembly connector.


b.

Disconnect the F55 blower resistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F5-6 (M2) - F55-2 (M2) Always Below 1 Ω
F5-1 (M1) - F55-3 (M1) Always Below 1 Ω
F5-10 (E) - Body ground Always Below 1 Ω
F5-6 (M2) or F55-2 (M2) - Body ground Always 10 kΩ or higher
F5-1 (M1) or F55-3 (M1) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F5-10 (M2) - F55-3 (M2) Always Below 1 Ω
F5-1 (M1) - F55-2 (M1) Always Below 1 Ω
F5-6 (E) - Body ground Always Below 1 Ω
F5-10 (M2) or F55-3 (M2) - Body ground Always 10 kΩ or higher
F5-1 (M1) or F55-2 (M1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (HEATER RELAY - HEATER CONTROL AND ACCESSORY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (HEATER RELAY - HEATER CONTROL AND ACCESSORY ASSEMBLY)
a.

Remove the heater relay.


b.

Disconnect the F5 heater control and accessory assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F78-1 - F5-3 (LO) Always Below 1 Ω
F78-1 or F5-3 (LO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR