Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2013.08–2013.12
RM30M0E _59 Vehicle Exterior _017122 DOOR / HATCH _0087456 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


PROCEDURE

Hide 67862 1.INSTALL FRONT DOOR WEATHERSTRIP

a.
B356960

Engage the 15 clips and install the front door weatherstrip.


b.

Install the clip.


Hide 68610 2.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door check assembly.


b.
B346730C01
0.729,0.229 0.938,0.438 0.208,0.208 10 true *a 2.135,0.229 2.333,0.427 0.198,0.198 10 true *b
*a Door Panel Side
*b Body Panel Side


Install the front door check assembly onto the door panel side with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



d.

Install the front door check assembly onto the body panel side with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 67001A 3.INSTALL FRONT DOOR PANEL CUSHION

a.
B346729

Install the 2 front door panel cushions.


Hide 69312 4.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B346736C01
1.563,2.156 1.323,2.135 false 2.781,2.448 2.906,2.229 true 1.104,2.031 1.417,2.229 0.313,0.198 10 false *a 2.854,2.042 3.167,2.24 0.313,0.198 10 false *a
*a Snap Ring


Install the front door lock open rod to the front door outside handle frame sub-assembly.


b.

Engage the snap ring as shown in the illustration.


Hide 69202A 5.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (w/ Smart Entry and Start System)

a.

Apply MP grease to the sliding parts of the front door outside handle frame sub-assembly.


b.
B353775

Engage the claw and the clamp, and connect the wire harness to the front door outside handle frame sub-assembly.


c.
B353776C01
0.938,1.958 1.375,1.698 true 0.458,1.427 0.844,1.219 true 0.292,1.406 0.604,1.604 0.313,0.198 10 false *a 0.76,1.927 1.073,2.125 0.313,0.198 10 false *b
*a Guide
*b Clamp


Engage the guide and install the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.


d.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


e.

Engage the clamp.


Hide 69202A 6.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (w/o Smart Entry and Start System)

a.

Apply MP grease to the sliding parts of the front door outside handle frame sub-assembly.


b.
B346738

Engage the guide and install the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242E 7.INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B346724

Engage the 2 claws and install the front door outside handle rear pad.


Hide 69241H 8.INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B346723

Engage the 2 claws and install the front door outside handle front pad.


Hide 69220 9.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/ Smart Entry and Start System)

Hide 69220 10.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/o Smart Entry and Start System)

a.
B346739

Install the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.


Hide 69320 11.INSTALL FRONT DOOR LOCK ASSEMBLY

Hide 69217F 12.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (w/ Lock Cylinder)

a.
B346720

Engage the 2 claws and install the front door outside handle cover to the lock cylinder.


b.

Apply MP grease to the sliding parts of the lock cylinder.


c.
B353772C01
2.5,1.906 2.802,1.906 false 2.865,1.844 3.177,2.042 0.313,0.198 10 false *1
*1 Hole Plug


Install the front door outside handle cover with lock cylinder.

HINT:

Make sure that the lock cylinder is inserted into the front door lock assembly.



d.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


e.

Install the hole plug.


Hide 69217F 13.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (w/o Lock Cylinder)

a.
B353773C01
0.698,1.917 0.938,1.917 false 0.51,1.844 0.823,2.042 0.313,0.198 10 false *1
*1 Hole Plug


Engage the 2 claws and install the front door outside handle cover.


b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Install the hole plug.


Hide 67404F 14.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B346718

Engage the guide and install the front door rear lower frame sub-assembly.


b.

Install the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 67924 15.INSTALL FRONT DOOR NO. 2 STIFFENER CUSHION

a.
B346717C01
1.979,0.833 2.313,0.833 true 2.375,0.74 2.688,0.938 0.313,0.198 10 true *a
*a Double-sided Tape


Install a new front door No. 2 stiffener cushion with the 2 bolts.

HINT:

Peel off the backing paper from the double-sided tape before installing the front door No. 2 stiffener cushion.


Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


b.

Apply though pressure to the sections with double-sided tape.


Hide 69820 16.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY (w/ Power Window)

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.
B346716C01
2.063,0.375 1.823,0.188 true 1.688,0.104 1.896,0.292 0.208,0.188 10 true *a
*a Temporary Bolt


Temporarily install the temporary bolt to the front door window regulator assembly.


c.

Temporarily install the front door window regulator assembly.


d.

Install the front door window regulator assembly with the 5 bolts and tighten the temporary bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 69820 17.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY (w/o Power Window)

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.
B347100

Install the front door window regulator assembly with the 5 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67664C 18.INSTALL DOOR FRAME GARNISH

a.
B356959

Engage the clamp and install a new door frame garnish.


Hide 68151D 19.INSTALL FRONT DOOR GLASS RUN

a.
B346712

Install the front door glass run.


Hide 68102 20.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

w/ Power Window:

i.

Connect the power window regulator master switch assembly.


ii.

Connect the cable to the negative (-) battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolt holes can be seen.


iv.

Disconnect the cable from the negative (-) battery terminal.


v.

Disconnect the power window regulator master switch assembly.



b.

w/o Power Window:

i.

Install the front door window regulator handle assembly.


ii.

Move the front door glass sub-assembly so that the door glass bolt holes can be seen.


iii.

Remove the front door window regulator handle assembly.



c.
B346740E01
1.896,0.073 2.354,0.271 0.458,0.198 10 false (1) 0.823,0.167 1.281,0.365 0.458,0.198 10 false (2)

Insert the front door glass sub-assembly into the front door panel as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly.



d.
B346714

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not damage the front door glass sub-assembly.



Hide 67832 21.INSTALL FRONT DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the front door panel.


b.

Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.


c.
B346741C01
0.469,0.396 0.594,0.292 false 2.833,0.396 2.719,0.323 false 0.573,0.177 0.885,0.333 0.313,0.156 10 false *a 2.573,0.229 2.885,0.385 0.313,0.156 10 false *a
*a Reference Point


Install the front door service hole cover according to the reference points on the front door panel.

NOTICE:

Securely install the front door service hole cover, taking care to prevent wrinkles and air bubbles.



Hide 68172A 22.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B346710

Install the front door glass inner weatherstrip.


Hide 75922M 23.INSTALL NO. 1 BLACK OUT TAPE (w/ Black Out Tape)

Hide 75756C 24.INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING

Hide 68210C 25.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 87940 26.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY (w/ Power Mirror Adjust Function)

Hide 87940 27.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY (w/o Power Mirror Adjust Function)

Hide 86160 28.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 69206B 29.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B346709

Engage the 4 guides and install the front door inside handle sub-assembly to the front door trim board sub-assembly.


Hide 67602 30.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B356958C01
1.24,0.604 1.156,0.354 false 1.01,1.083 1.167,0.875 true 0.99,0.229 1.302,0.427 0.313,0.198 10 false *1 0.875,1.115 1.188,1.313 0.313,0.198 10 false *2
*1 Front door inside locking cable assembly
*2 Front door lock remote control cable assembly


Engage the 2 guides and connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door trim board sub-assembly.


b.
B346707

Engage the 5 claws and the guide.


c.

Engage the 8 clips and install the front door trim board sub-assembly.


d.
B346706

Install the 3 screws.


e.
B347469

Engage the claw and close the door inside handle bezel plug.


Hide 74232 31.INSTALL FRONT ARMREST BASE UPPER PANEL (w/ Power Window)

a.
B346704

Connect the connector.


b.
B346703

Engage the 9 claws and install the front armrest base upper panel.


Hide 74232 32.INSTALL FRONT ARMREST BASE UPPER PANEL (w/o Power Window)

a.
B347098

Engage the 7 claws and install the front armrest base upper panel.


Hide 69260 33.INSTALL FRONT DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.

Install the front door window regulator handle assembly and fully open the front door glass sub-assembly.


b.

Remove the front door window regulator handle assembly.


c.
B346721C01
2.333,0.542 2.646,0.74 0.313,0.198 10 false *a 2.906,0.542 3.094,0.74 0.188,0.198 10 false *b
*a Door Panel Side
*b Inside of Vehicle


Install the window regulator handle plate as shown in the illustration.


d.
B346726C01
3.104,0.813 3.354,1.052 0.25,0.24 10 false *a 2.823,1.073 3.135,1.271 0.313,0.198 10 false 0° 2.281,0.135 2.74,0.333 0.458,0.198 10 false 60° 2.656,0.5 2.969,0.698 0.313,0.198 10 false *b
*a Front of Vehicle
*b Assemble with Glass in Fully Open Position


Install the front door window regulator handle assembly with the shaft snap ring at the angle shown in the illustration.


Hide 67492A 34.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B346702

Engage the 2 clips and install the front door lower frame bracket garnish.


Hide 35.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

Hide 36.INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side with Power Window)

Hide 37.INSPECT POWER WINDOW OPERATION (for Driver Side with Power Window)