Home › Drivetrain › CLUTCH › CLUTCH MASTER CYLINDER(for RHD) › 2013.08–2017.10
RM30M0E _52 Drivetrain _017089 CLUTCH _0091164 CLUTCH MASTER CYLINDER(for RHD) A

CLUTCH  CLUTCH MASTER CYLINDER(for RHD)  INSTALLATION  


PROCEDURE

Hide 31453 1.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS

a.
C125988C02
2.177,0.885 2.594,0.469 false 1.635,1.104 1.115,0.5 false 0.969,0.396 1.281,0.552 0.313,0.156 10 false *1 2.625,0.365 2.938,0.521 0.313,0.156 10 false *2 1.135,1.844 1.292,2.042 0.156,0.198 10 false A
*1 Lock Nut
*2 Clutch Master Cylinder Push Rod Clevis


Install the lock nut to the clutch master cylinder assembly.


b.

Install the clutch master cylinder push rod clevis to the clutch master cylinder assembly.


c.

Tighten the lock nut and check the dimension A is the same as the dimension A that was measured during removal.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)

NOTICE:

When tightening the lock nut, be sure to hold the clutch master cylinder push rod clevis in place by its square portion.



Hide 31410 2.INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

a.
C235127E01
1.344,0.438 1.469,0.615 0.125,0.177 10 true 1 1.688,1.458 1.813,1.635 0.125,0.177 10 true 2

Install the clutch master cylinder assembly to the body with the 2 nuts in the order shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 31453 3.CONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS

Hide 31481 4.CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

a.

Using a 10 mm union nut wrench, connect the clutch master cylinder to flexible hose tube to the clutch master cylinder assembly.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



Hide 31434C 5.CONNECT CLUTCH RESERVOIR TUBE

a.
C289157C01
1.427,2.542 1.667,2.698 true 1.031,2.26 1.344,2.417 0.313,0.156 10 false *a 1.646,2.271 1.958,2.427 0.313,0.156 10 false *b 2.146,2.75 2.458,2.906 0.313,0.156 10 false *c 1.281,2.448 1.594,2.604 0.313,0.156 10 false *d 0.479,0.969 0.635,1.167 0.156,0.198 10 false A
*a View A
*b Upper Side of Vehicle
*c Left Side of Vehicle
*d Paint Mark


Connect the clutch reservoir tube to the clutch master cylinder assembly with the hose clip as shown in the illustration.

NOTICE:

Perform the installation with the hose clip and the paint mark of the clutch reservoir tube at the correct direction.



Hide 6.FILL RESERVOIR WITH BRAKE FLUID

Hide 8.INSPECT FOR BRAKE FLUID LEAK

Hide 9.INSPECT BRAKE FLUID LEVEL IN RESERVOIR

Hide 10.INSPECT AND ADJUST CLUTCH PEDAL

Hide 55432B 11.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL

Hide 55606 12.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY