The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.
When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Under normal conditions, the MIL is illuminated when the ignition switch is turned to ON. The MIL goes off when the engine is started.
ECM Power Source Circuit
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>ECM Power Source Circuit
VC Output Circuit
Check the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine and ECT" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Turn the ignition switch to ON.
| *A | for CVT |
| *B | for Manual Transaxle |
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F131-1 (+B) - B46-3 (E1) | Ignition switch ON | 11 to 14 V |
| F131-2 (+B2) - B46-3 (E1) | Ignition switch ON | 11 to 14 V |
If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the S1 vacuum sensor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine and ECT" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the B17 throttle body with motor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine and ECT" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
A
B
Disconnect the B35 crankshaft position sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine and ECT" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the B45 camshaft position sensor (for intake camshaft) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine and ECT" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the B44 camshaft position sensor (for exhaust camshaft) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine and ECT" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible (for CVT) | A |
| Communication is not possible (for Manual Transaxle) | B |
| Communication is possible | C |
A
B
C
Disconnect the B49 oil pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine and ECT" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the A33 accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine and ECT" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the F117 atmospheric pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
The Data List item "Engine and ECT" can be checked.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the S1 vacuum sensor assembly connector.
Disconnect the B17 throttle body with motor assembly connector.
Disconnect the B35 crankshaft position sensor connector.
Disconnect the B45 camshaft position sensor (for intake camshaft) connector.
Disconnect the B44 camshaft position sensor (for exhaust camshaft) connector.
Disconnect the B49 oil pressure sensor connector (for CVT).
Disconnect the A33 accelerator pedal sensor assembly connector.
Disconnect the F117 atmospheric pressure sensor connector.
Disconnect the B46, F130 and F131 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F130-27 (VCPB) - Body ground and other terminals | Always | 10 kΩ or higher |
| B46-29 (VCTA) - Body ground and other terminals | Always | 10 kΩ or higher |
| B46-33 (VCNE) - Body ground and other terminals | Always | 10 kΩ or higher |
| B46-21 (VCV1) - Body ground and other terminals | Always | 10 kΩ or higher |
| B46-31 (VCE1) - Body ground and other terminals | Always | 10 kΩ or higher |
| F130-32 (VCPT)*1 - Body ground and other terminals | Always | 10 kΩ or higher |
| F131-20 (VCPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| F131-22 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
| F130-33 (VHAC) - Body ground and other terminals | Always | 10 kΩ or higher |
*1: for CVT
| Proceed to |
|---|
| OK |
| NG |
OK
NG