The brake ejector VSV is installed on the throttle by-pass and controlled by the ECM to optimally apply vacuum to the brake booster assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| C1263 | Ejector VSV Malfunction (High) | Both of the following conditions are met for 3 seconds or more (1 trip detection logic): 1.
Ignition switch is ON. 2.
Short to +B in brake ejector VSV circuit when VSV operation command is on. |
·
Short to +B in brake ejector VSV circuit ·
Brake ejector VSV ·
ECM |
Does not come on | DTC stored |
| C1264 | Ejector VSV Malfunction (Low) | Both of the following conditions are met for 3 seconds or more (1 trip detection logic): 1.
Ignition switch is ON. 2.
Open or short to ground in brake ejector VSV circuit when VSV operation command is off. |
·
Open or short in brake ejector VSV circuit ·
Brake ejector VSV ·
ECM |
Does not come on | DTC stored |
The ECM monitors the terminal voltage input from the brake ejector VSV. If the voltage and brake ejector VSV operation command signal do not match, the ECM judges that there is a malfunction in the brake ejector VSV circuit and stores a DTC.
| Required Sensors/Components | Brake ejector VSV |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
The A/C (if equipped) and all accessory switches should be off.
Idle the engine for 15 minutes or more [B].
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: C1263 or C1264.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].
Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Check the DTC judgment result again [E].
Inspect the fuses for circuits related to this system before performing the following procedure.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| *1 | Brake ejector VSV |
| *2 | Vacuum hose (Air cleaner side) |
Disconnect the vacuum hose (Air cleaner side) of the brake ejector VSV.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Brake Ejector VSV Inspection.
| Tester Display |
|---|
| Brake Ejector VSV Inspection |
When the brake ejector VSV is operated using the GTS, check whether the port of the brake ejector VSV applies suction your finger.
| GTS Operation | Specified Condition |
|---|---|
| ON | Brake ejector VSV port applies suction to finger |
| OFF | Brake ejector VSV port applies no suction to finger |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the brake ejector VSV.
Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM SWITCHING VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Brake Ejector VSV) |
Disconnect the brake ejector VSV connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B52-1 - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B52 brake ejector VSV connector.
Disconnect the B47 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B47-14 (PBV) - B52-2 | Always | Below 1 Ω |
| B47-14 (PBV) or B52-2 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the B52 brake ejector VSV connector.
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B52-1 - 2H-4 | Always | Below 1 Ω |
| B52-1 or 2H-4 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG