Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE ASSEMBLY(for 1NR-FE) › 2016.04–2016.07
RM30M0E _52 Drivetrain _017091 C54 MANUAL TRANSMISSION / TRANSAXLE _0267613 MANUAL TRANSAXLE ASSEMBLY(for 1NR-FE) A

C54 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(for 1NR-FE)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 12262 4.DISCONNECT NO. 2 VENTILATION HOSE

Hide 17880 5.REMOVE AIR CLEANER HOSE ASSEMBLY

Hide 17801 7.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 33820B 12.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C294354E01
0.927,1.115 1.063,1.302 0.135,0.188 10 true A 1.021,2.083 1.177,2.281 0.156,0.198 10 true A 2.292,0.375 2.448,0.552 0.156,0.177 10 true B 2.688,1.583 2.844,1.781 0.156,0.198 10 false B

Remove the 2 clips A and 2 washers to disconnect the transmission control cable assembly from the manual transaxle assembly.


b.

Remove the 2 clips B to separate the transmission control cable assembly from the floor shift control lever housing support bracket.


Hide 82121 13.DISCONNECT ENGINE WIRE

a.

w/o ABS:

i.
C355128

Disconnect the connector from the speedometer sensor.



b.
C294364E01
1.823,1.594 1.979,1.76 0.156,0.167 10 true A 1.271,2.844 1.438,3.031 0.167,0.188 10 true B

Disconnect the connector from the back-up light switch assembly.


c.

Disconnect the connector from the oxygen sensor.


d.

Remove the bolt A to separate the engine wire from the manual transaxle assembly.


e.

Disengage the 7 clamps to separate the engine wire from the wire harness clamp brackets.


f.

Remove the bolt B and wire harness clamp bracket from the manual transaxle assembly.


Hide 31470 14.SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY

a.
C294365E01
1.896,1.104 2.042,1.292 0.146,0.188 10 true A 2.927,0.781 3.083,0.958 0.156,0.177 10 true A 1.26,0.594 1.406,0.781 0.146,0.188 10 true B 0.354,0.427 0.531,0.594 0.177,0.167 10 true B

Remove the clip.


b.

Remove the 2 bolts A to separate the clutch release cylinder to flexible hose tube from the manual transaxle assembly.


c.

Remove the 2 bolts B to separate the clutch release cylinder assembly from the manual transaxle assembly.

NOTICE:
·

Suspend the clutch release cylinder assembly with a piece of rope so as not to place stress on the clutch line.

·

Do not depress the clutch pedal.




Hide 57533B 15.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 16.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 43498A 17.REMOVE NO. 1 DRIVE SHAFT HEAT INSULATOR

Hide 18.REMOVE FRONT DRIVE SHAFT ASSEMBLIES

Hide 28100 19.REMOVE STARTER ASSEMBLY

Hide 51201 20.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 21.SUPPORT ENGINE ASSEMBLY

a.
C294385

Remove the 4 bolts from the engine assembly side.


b.
C294367C01
0.5,2.219 0.625,1.99 false 1.083,1.469 1.49,1.563 true 1.927,1.573 2.354,1.583 true 1.198,0.698 1.531,1.219 true 2.365,1.5 2.594,1.688 0.229,0.188 10 true *a 1.031,0.625 1.344,0.781 0.313,0.156 10 false *b 0.396,2.208 0.708,2.365 0.313,0.156 10 false *c 0.917,1.354 1.083,1.542 0.167,0.188 10 true *a
*a Height Adjustment Attachments
*b Plate Lift Attachment
*c Engine Lifter
V100155

Attachment Placement Position


Place the height adjustment attachments and plate lift attachments in the positions shown in the illustration and set the engine lifter underneath the engine assembly.

NOTICE:
·

Place the height adjustment attachments and plate lift attachments so that the engine assembly with the manual transaxle assembly is level.

·

As the engine assembly with the manual transaxle assembly is very heavy, be sure to support it securely.




Hide 12313 22.REMOVE ENGINE MOVING CONTROL ROD BRACKET

a.
C294368

Remove the 4 bolts and engine moving control rod bracket from the manual transaxle assembly.


Hide 30300 23.REMOVE MANUAL TRANSAXLE ASSEMBLY

a.

Set the transmission jack underneath the manual transaxle assembly.

NOTICE:

Secure the manual transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.



b.
C294378

Remove the bolt and nut to separate the engine mounting insulator LH from the engine mounting bracket LH.

HINT:

Turn the bolt while holding the nut.



c.
C294379

Remove the 5 bolts.


d.

Disengage the hook to remove the engine mounting insulator LH from the body.


e.
C294380

Remove the 5 bolts and engine mounting bracket LH from the manual transaxle assembly.


f.
C294376C01
2.813,0.813 3.021,1.052 false 0.75,1.99 0.469,2.042 false 0.323,1.458 0.188,1.635 false 2.896,1.896 2.719,1.76 false 0.323,1.958 0.635,2.104 0.313,0.146 10 false *1 2.938,1.833 3.25,1.99 0.313,0.156 10 false *2 2.656,0.719 2.969,0.875 0.313,0.156 10 false *a 3.177,1.604 3.385,1.823 0.208,0.219 10 false *b 0.094,1.625 0.406,1.781 0.313,0.156 10 false *a
*1 Engine Assembly
*2 Manual Transaxle Assembly
*a Body
*b Tilt 50 mm (1.97 in.) or less
V100145

Watch for Interference


Operate the engine lifter and transmission jack, and slowly tilt the engine assembly with the manual transaxle assembly 50 mm (1.97 in.) or less.

NOTICE:
·

Do not allow the engine assembly and manual transaxle assembly to interfere with the body.

·

Make sure that the engine assembly is not tilted more than necessary.

·

Make sure that the wire harness and hoses are not being pulled.




g.
C294386

Remove the 4 bolts from the manual transaxle assembly side.


h.
C294377C01
1.479,1.896 1.802,1.49 true 1.771,1.906 1.854,1.615 true 2,1.969 1.917,1.396 true 1.385,1.917 1.698,2.073 0.313,0.156 10 false *1 1.688,1.938 2,2.094 0.313,0.156 10 false *2 1.948,1.969 2.26,2.125 0.313,0.156 10 false *3
*1 Clutch Disc Assembly
*2 Clutch Cover Assembly
*3 Input Shaft
V100145

Watch for Interference


Using the transmission jack, remove the manual transaxle assembly from the engine assembly according to the procedures shown in the illustration.

NOTICE:
·

To prevent damage to the knock pins, do not pry between the manual transaxle assembly and engine assembly.

·

To prevent damage to the input shaft, do not forcefully shake the manual transaxle assembly.

·

Make sure the manual transaxle assembly does not interfere with the clutch tube or other components.



i.

Move the manual transaxle assembly towards the left side of the vehicle and disengage the input shaft from the clutch disc assembly.


ii.

Tilt the manual transaxle assembly and pull the input shaft out from the clutch cover assembly.


iii.

Lower the manual transaxle assembly.



Hide 24.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C294381

Remove the 3 bolts and 3 wire harness clamp brackets from the manual transaxle assembly.


Hide 33403K 25.REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY (w/ ABS)

a.
C294382

Remove the bolt and speedometer driven hole cover sub-assembly from the manual transaxle assembly.


b.

Remove the O-ring from the speedometer driven hole cover sub-assembly.


Hide 83181G 26.REMOVE SPEEDOMETER SENSOR (w/o ABS)