When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM stores a DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0300 | Random / Multiple Cylinder Misfire Detected | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Fuel line ·
Fuel pump ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
Comes on/Blinks*1 (Euro-OBD) / - (Except Euro-OBD)
*1: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
| P0301 | Cylinder 1 Misfire Detected | Misfiring of the No. 1 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Fuel line ·
Fuel pump ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
Comes on/Blinks*1 (Euro-OBD) / - (Except Euro-OBD)
*1: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
| P0302 | Cylinder 2 Misfire Detected | Misfiring of the No. 2 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Fuel line ·
Fuel pump ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
Comes on/Blinks*1 (Euro-OBD) / - (Except Euro-OBD)
*1: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
| P0303 | Cylinder 3 Misfire Detected | Misfiring of the No. 3 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Fuel line ·
Fuel pump ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
Comes on/Blinks*1 (Euro-OBD) / - (Except Euro-OBD)
*1: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
| P0304 | Cylinder 4 Misfire Detected | Misfiring of the No. 4 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Fuel line ·
Fuel pump ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
ECM |
Comes on/Blinks*1 (Euro-OBD) / - (Except Euro-OBD)
*1: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored |
When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.
The ECM illuminates the MIL and stores a DTC when the following condition, which could cause emission deterioration, is detected (2 trip detection logic).
An excessive number of misfires (approximately 89 to 104 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when the following condition, which could cause damage to the three-way catalytic converter, is detected.
At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
The ECM stores a DTC when the following condition, which could cause emission deterioration, is detected (2 trip detection logic).
An excessive number of misfires (approximately 450 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM stores a DTC (2 trip detection logic) when the following condition, which could cause damage to the three-way catalytic converter, is detected.
At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
| Required Sensors/Components (Main) | Crankshaft position sensor
Camshaft position sensor |
| Required Sensors/Components (Related) | Engine coolant temperature sensor
Intake air temperature sensor Mass air flow meter |
| Frequency of Operation | Continuous |
| Intake air temperature | Higher than -10°C (14°F) |
| Engine coolant temperature | Higher than 20°C (68°F) |
| Intake air temperature | Higher than -10°C (14°F) |
| Engine coolant temperature | Higher than 75°C (167°F) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Record the DTC(s) and freeze frame data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Using the GTS, switch the ECM from normal mode to check mode.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE
Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.
| Engine speed | Duration |
|---|---|
| Idling | 8.0 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
Check whether misfires have occurred by checking DTCs and freeze frame data.
Do not turn the ignition switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.
Record the DTC(s), freeze frame data and misfire counts.
Turn the ignition switch off and wait for at least 30 seconds.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Refer to DTC P0102.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>P0102
Refer to Fuel Injector Circuit.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>Fuel Injector Circuit
Inspect the fuses for circuits related to this system before performing the following procedure.
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
There was insufficient fuel in the tank.
Improper fuel was used.
The spark plugs have been contaminated.
The problem requires further diagnosis.
After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #4 Misfire Count).
Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (+15% or higher).
When Coolant Temp in the freeze frame data is below 75°C (167°F), the misfires have occurred only while warming up the engine.
An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.
Check the "Fuel Cut Elps Time" in the Data List or the Freeze Frame Data.
If the elapsed time is over 0 seconds, then the engine speed is high (engine speed at which fuel cut occurs + 500 rpm).
When this has happened, there is the possibility that the No. 1 valve rocker arm sub-assembly will become loose and a fire could start, so check that the No. 1 valve rocker arm sub-assembly is properly attached.
Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE UNIT>COMPONENTS
By clearing the DTC, "Fuel Cut Elps Time" will be cleared.
In the past, when the primary ignition system (the igniter drive circuit in the ECM, the primary circuit in the No. 1 ignition coil, the related wire harness, or the connector) was out of order, diagnostic codes from P0351 to P0354 were output. However, these codes are not output in this vehicle.
When a failure in the primary ignition system is suspected, refer to "Cat OT MF F/C History", "Cat OT MF F/C Cylinder #1 to #4", and "Cylinder #1 Misfire Count to Cylinder #4 Misfire Count" in the freeze frame data, the pending freeze frame data, and the Data List, and confirm in which cylinder the high-frequency misfire was concentrated.
Referring to the following contents of the freeze frame data (or the pending freeze frame data) enables an estimation of which cylinder has misfired and to what degree.
Cylinder #1 Misfire Count to Cylinder #4 Misfire Count: Misfire count according to cylinder.
Cat OT MF F/C Cylinder #1 to #4: This expresses a high-frequency misfire was concentrated in a certain cylinder and that cylinder's fuel injection was stopped.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections.
Click hereEngine / Hybrid System>2NR-FE EMISSION CONTROL>PCV VALVE>COMPONENTS
PCV valve and hose are correctly connected and are not damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.
| Tester Display |
|---|
| Misfire RPM |
| Misfire Load |
Read and note the Misfire RPM and Misfire Load values.
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
| Result | Proceed to |
|---|---|
| NEXT (Euro-OBD) | A |
| NEXT (Except Euro-OBD) | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA
| Freeze Frame Data Item | Result | Proceed to |
|---|---|---|
| Cat OT MF F/C History | ON | A |
| OFF | B |
A
B
Inspect the spark plug of the misfiring cylinder.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
According to the "Cat OT MF F/C History and Cat OT MF F/C Cylinder #1 to #4" on the Data List, check the spark plug of the malfunctioning cylinder.
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.
| Tester Display |
|---|
| Prohibit the Catalyst OT Misfire prevent F/C |
Perform the Active Test.
When performing the Active Test, make sure the vehicle is stopped and the engine is either idling or being revved within 3000 rpm.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.
| Tester Display |
|---|
| Cylinder #1 Misfire Count |
| Cylinder #2 Misfire Count |
| Cylinder #3 Misfire Count |
| Cylinder #4 Misfire Count |
Start the engine and allow the engine to idle.
Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the GTS. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].
Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the GTS [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.
If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.
| Result | Proceed to |
|---|---|
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
A
B
Inspect the spark plug of the misfiring cylinder.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B47-4 (#10) - B46-1 (E01) | Ignition switch ON | 11 to 14 V |
| B47-3 (#20) - B46-1 (E01) | Ignition switch ON | 11 to 14 V |
| B47-2 (#30) - B46-1 (E01) | Ignition switch ON | 11 to 14 V |
| B47-1 (#40) - B46-1 (E01) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>2NR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel pressure.
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Read the Data List twice, when the engine is both cold and warmed up.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed, MAF and Coolant Temp.
| Tester Display |
|---|
| Engine Speed |
| MAF |
| Coolant Temp |
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| MAF | Shift lever position: N (neutral)
A/C*1: off Engine Speed: 3000 rpm |
Between 3.0 gm/sec and 8.0 gm/sec |
*1: w/ Air Conditioning System
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>2NR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel pressure.
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.
| Tester Display |
|---|
| Coolant Temp |
Read the Data List twice, when the engine is both cold and warmed up.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed, MAF and Coolant Temp.
| Tester Display |
|---|
| Engine Speed |
| MAF |
| Coolant Temp |
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 3000 rpm.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| MAF | Shift lever position: N (neutral)
A/C*1: off Engine Speed: 3000 rpm |
Between 3.0 gm/sec and 9.0 gm/sec |
*1: w/ Air Conditioning System
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 ignition coil and the spark plug from the misfiring cylinder.
Inspect the spark plug of the misfiring cylinder.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform a spark test.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B47-4 (#10) - B46-1 (E01) | Ignition switch ON | 11 to 14 V |
| B47-3 (#20) - B46-1 (E01) | Ignition switch ON | 11 to 14 V |
| B47-2 (#30) - B46-1 (E01) | Ignition switch ON | 11 to 14 V |
| B47-1 (#40) - B46-1 (E01) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and warm it up.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output) |
B |
A
B
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.
Repair any problems.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and warm it up.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output) |
B |
A
B
OK
NG
Replace the mass air flow meter.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL
If the results of the inspections performed in steps 17 and 22 indicated no problem, proceed to the next step without replacing the mass air flow meter.
Perform "Inspection After Repair" after replacing the mass air flow meter.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and warm it up.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output) |
B |
A
B
Inspect the fuel pump.
Click hereEngine / Hybrid System>2NR-FE FUEL>FUEL PUMP>INSPECTION
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG