Home › Engine / Hybrid System › 2NR-FE ENGINE MECHANICAL › ENGINE › from 2016.04
RM30M0E _51 Engine / Hybrid System _053933 2NR-FE ENGINE MECHANICAL _0262358 ENGINE G

2NR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner hose assembly.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL



c.

Remove the air cleaner filter element sub-assembly.

Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for Manual Transaxle)>REMOVAL


d.

Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily. If necessary, replace the air cleaner filter element sub-assembly.

HINT:
·

If there is any foreign matter or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any foreign matter or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




e.

f.

Install the air cleaner cap sub-assembly.


g.

Install the air cleaner hose assembly.


Hide 16361A 6.INSPECT FAN AND GENERATOR V BELT

Hide 16620 7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

a.

Remove the fan and generator V belt.

Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>DRIVE BELT>REMOVAL


b.

Check that nothing is caught in the V-ribbed belt tensioner assembly by turning it clockwise and counterclockwise. If a malfunction exists, replace the V-ribbed belt tensioner assembly.


c.

Install the fan and generator V belt.

Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>DRIVE BELT>INSTALLATION


Hide 8.INSPECT VALVE LASH ADJUSTER NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises. If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the preceding inspections.

HINT:

If any defects or problems are found during the preceding inspections, perform valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION



Hide 9.INSPECT IGNITION TIMING

a.

When using the GTS:

i.

Warm up the engine.


ii.

Turn all the electrical systems and the A/C off.


iii.

Turn the ignition switch off.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS on.


vii.

Start the engine.


viii.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29
Standard ignition timing:
Transaxle Ignition Timing
Continuously variable transaxle -10 to 10 degrees BTDC
Manual Transaxle


NOTICE:
·

Inspect the ignition timing with the cooling fan off.

·

When checking the ignition timing, the transaxle should be in neutral or park.




ix.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

x.

Monitor IGN Advance of the Data List.

Standard ignition timing:
Transaxle Ignition Timing
Continuously variable transaxle 8 to 12 degrees BTDC
Manual Transaxle


NOTICE:

When checking the ignition timing, the transaxle should be in neutral or park.



xi.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / OFF.


xii.

Check that the ignition timing advances immediately when the engine speed is increased.


xiii.

Turn the ignition switch off.


xiv.

Disconnect the GTS from the DLC3.



b.

When not using the GTS:


ii.
A312659

Pull out the wire harness shown in the illustration.

NOTICE:

After checking, wrap the wire harness with tape.



iii.

Warm up the engine.


iv.

Turn all the electrical systems and the A/C off.


v.

Turn the ignition switch off.


vi.

Connect the clip of the timing light to the wire harness.

NOTICE:

Use a timing light that detects the first signal.



vii.
A206183C30
1.583,0.906 1.313,0.542 true 1.771,1.479 2.063,1.823 true 1.01,0.406 1.292,0.604 0.281,0.198 10 false CG 2.156,1.771 2.417,1.948 0.26,0.177 10 false TC 0.094,0.083 0.406,0.24 0.313,0.156 10 false *1
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.



viii.

Start the engine.


ix.
A312658C01
0.802,1.365 0.948,1.531 false 0.927,0.99 1.167,0.938 true 0.729,1.135 1.031,0.344 true 0.365,1.469 0.594,1.229 true 0.885,1.521 1.198,1.677 0.313,0.156 10 false *a 1.177,0.823 1.49,0.979 0.313,0.156 10 false *b 1.042,0.208 1.354,0.365 0.313,0.156 10 false *c 0.208,1.385 0.521,1.542 0.313,0.156 10 false *d 0.229,0.594 0.542,0.75 0.313,0.156 10 false *e
*a Timing Notch of Crankshaft Pulley
*b TDC Mark
*c 8 degrees BTDC Mark
*d 12 degrees BTDC Mark
*e 8 to 12 degrees BTDC


Inspect the ignition timing at idle.

Standard ignition timing:
Transaxle Ignition Timing
Continuously variable transaxle 8 to 12 degrees BTDC
Manual Transaxle


NOTICE:
·

Inspect the ignition timing with the cooling fan off.

·

When checking the ignition timing, the transaxle should be in neutral or park.



HINT:

After running the engine at 1000 to 1300 rpm for 5 seconds, check that it returns to idle speed.



x.

Disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.


xi.

Inspect the ignition timing at idle.

Standard ignition timing:
Transaxle Ignition Timing
Continuously variable transaxle -10 to 10 degrees BTDC
Manual Transaxle



xii.

Check that the ignition timing advances immediately when the engine speed is increased.


xiii.

Turn the ignition switch off.


xiv.

Remove the timing light.




Hide 10.INSPECT ENGINE IDLE SPEED

a.

When using the GTS:

i.

Warm up the engine.


ii.

Turn all the electrical systems and the A/C off.


iii.

Turn the ignition switch off.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS on.


vii.

Start the engine.


viii.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

ix.

Inspect the engine idle speed.

Standard idle speed:
Transaxle Idle Speed
Continuously variable transaxle 680 to 780 rpm
Manual Transaxle 550 to 650 rpm


NOTICE:
·

Inspect the idling speed with the cooling fan off.

·

When checking the idle speed, the transaxle should be in neutral or park.




x.

Turn the ignition switch off.


xi.

Disconnect the GTS from the DLC3.



b.

When not using the GTS:

i.

Warm up the engine.


ii.

Turn all the electrical systems and the A/C off.


iii.

Turn the ignition switch off.


iv.
A206183C31
1.052,1.469 0.813,1.76 true 0.625,1.833 0.969,2.021 0.344,0.188 10 false TAC 0.104,0.104 0.417,0.26 0.313,0.156 10 false *1
*1 DLC3


Using SST, connect terminal 9 (TAC) of the DLC3.

SST
09843-18040  

NOTICE:

Be sure to connect the tachometer to the correct terminal. Connecting the wrong terminals can cause damage.



v.

Connect a tachometer.


vi.

Start the engine.


vii.

Inspect the engine idle speed.

Standard idle speed:
Transaxle Idle Speed
Continuously variable transaxle 680 to 780 rpm
Manual Transaxle 550 to 650 rpm


NOTICE:
·

Inspect the idling speed with the cooling fan off.

·

When checking the idle speed, the transaxle should be in neutral or park.




viii.

Turn the ignition switch off.


ix.

Disconnect the tachometer.


x.

Disconnect SST from terminal 9 (TAC) of the DLC3.



Hide 11.INSPECT COMPRESSION

NOTICE:

Keep the intake manifold and spark plug holes free of foreign matter when measuring the compression pressure.



b.

Warm up and stop the engine.



d.

Disconnect the 4 fuel injector connectors.

NOTICE:

Disable fuel injection in order to prevent catalyst damage due to unburned gasoline.



e.
A198282

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Standard pressure:

1200 kPa (12.2 kgf/cm2, 174 psi)


Minimum pressure:

900 kPa (9.2 kgf/cm2, 131 psi)


Difference between each cylinder:

98 kPa (1.0 kgf/cm2, 14.2 psi) or less


NOTICE:
·

Use a fully-charged battery so that the engine speed can be increased to 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression pressure in as short a time as possible.




iv.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole, then inspect it again.

HINT:
·

If adding engine oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the cylinder head gasket.





f.

Connect the 4 fuel injector connectors.



h.

Clear the DTCs.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



Hide 12.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with local regulations.


a.

Warm up the engine.


b.

Keep the engine speed at 2500 rpm for approximately 180 seconds.


c.

Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe during idle.


d.

Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

HINT:

When performing the 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with local regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Possible Cause
Normal High Rough idle
1.

Faulty ignition:

·

Incorrect timing

·

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leaks in from intake or exhaust valves

4.

Leaks in from cylinders


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

·

PCV hoses

·

Intake manifold

·

Throttle body with motor assembly

·

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty EFI system:

·

Fuel pressure regulator assembly

·

Engine coolant temperature sensor

·

Mass air flow meter

·

ECM

·

Fuel injector assembly

·

Throttle body with motor assembly