33403M
1.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
Apply a light coat of Toyota Genuine ATF Type T-IV to a new O-ring and install it to the speedometer driven hole cover sub-assembly.
Do not twist the O-ring.
Install the speedometer driven hole cover sub-assembly to the automatic transaxle assembly with the bolt.
Make sure that the O-ring is not damaged or does not jump out of position during installation.
35013
2.INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY
Apply a light coat of Toyota Genuine ATF Type T-IV to a new O-ring and install it to the transmission oil filler tube sub-assembly.
Do not twist the O-ring.
Install the transmission oil filler tube sub-assembly to the automatic transaxle assembly with the bolt.
Make sure that the O-ring is not damaged or does not jump out of position during installation.
Connect the breather hose to the transmission oil filler tube sub-assembly.
35103
3.INSTALL TRANSMISSION OIL LEVEL DIPSTICK SUB-ASSEMBLY
Install the transmission oil level dipstick sub-assembly into the transmission oil filler tube sub-assembly.
32924
4.INSTALL NO. 2 OIL COOLER TUBE CLAMP
Temporarily install the outlet No. 1 oil cooler tube to the oil cooler tube union.
Temporarily install the inlet No. 1 oil cooler tube to the oil cooler tube union.
Install the No. 2 oil cooler tube clamp to the transmission oil filler tube sub-assembly with the bolt.
32922
5.CONNECT OUTLET NO. 1 OIL COOLER TUBE
| *a | Hold |
| *b | Turn |
Using a 14 mm union nut wrench, connect the outlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
32921
6.CONNECT INLET NO. 1 OIL COOLER TUBE
| *a | Hold |
| *b | Turn |
Using a 14 mm union nut wrench, connect the inlet No. 1 oil cooler tube while holding the oil cooler tube union with a wrench.
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
33829
7.INSTALL TRANSMISSION CONTROL CABLE SUPPORT
Install the transmission control cable support to the automatic transaxle assembly with the bolt.
33823
8.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Install the No. 1 transmission control cable bracket to the automatic transaxle assembly with the 2 bolts.
9.INSPECT TORQUE CONVERTER ASSEMBLY
10.INSTALL TORQUE CONVERTER ASSEMBLY
| *a | Key |
| *b | Matchmark |
Set the key at the top of the front oil pump drive gear and put a matchmark on the transaxle housing.
| *a | Groove |
| *b | Matchmark |
Place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.
| *1 | Front Oil Pump Oil Seal |
| *a | Matchmark |
Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the front oil pump oil seal.
| *1 | Front Oil Pump Oil Seal |
| *a | Matchmark |
Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the front oil pump oil seal.
| *1 | Front Oil Pump Oil Seal |
| *a | Matchmark |
Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the groove of the torque converter assembly into the key of the front oil pump drive gear.
Do not push the torque converter assembly excessively when rotating it.
Install the torque converter assembly to the input shaft while keeping it horizontal.
Do not damage the front oil pump oil seal.
Clean the drive plate and torque converter assembly setting bolt holes.
| *a | Engine Surface |
| *b | Drive Plate Surface |
Using a vernier caliper and straightedge, measure dimension A between the automatic transaxle assembly contact surface of the engine assembly*a and the torque converter assembly contact surface of the drive plate*b.
Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the previous step.
B = A + 1 mm (0.0394 in.) or more
Make sure to deduct the thickness of the straightedge.
If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.
Do not include the thickness of the set block.
30500
11.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY
| *1 | Crankshaft |
| *2 | Torque Converter Assembly Centerpiece |
|
Clutch Spline Grease |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1 g (0.0353 oz.)
| *1 | Knock Pin |
Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.
Maintain the engine assembly and automatic transaxle assembly in a horizontal position, align the knock pins with each hole in the automatic transaxle assembly and install the automatic transaxle assembly to the engine assembly with the 7 bolts.
Make sure that the wire harness or similar items are not pinched between the contact surfaces.
Do not forcibly pry on the automatic transaxle assembly.
When mounting the automatic transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.
Check that the torque converter assembly rotates.
When tightening the bolts, be sure that the contact surfaces of the engine assembly and automatic transaxle assembly are in close contact with one another.
Bolt A: Install from automatic transaxle assembly side
Bolt B: Install from engine assembly side
| *a | Adhesive |
Clean and degrease the engine mounting bracket LH installation bolts and bolt holes.
Apply adhesive to 2 or 3 threads on the ends of the 4 bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
| *a | Temporarily Tighten |
Install the engine mounting bracket LH to the automatic transaxle assembly with the 4 bolts in the order shown in the illustration.
Install the engine mounting bracket LH to the engine mounting insulator LH with the bolt and nut.
Turn the bolt while holding the nut.
12364B
12.INSTALL NO. 2 ENGINE MOVING CONTROL ROD
| *a | Temporarily Tighten |
Install the No. 2 engine moving control rod to the automatic transaxle assembly with the 3 bolts in the order shown in the illustration.
12321B
13.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
Install the drive shaft heat insulator sub-assembly to the engine assembly with the bolt.
Using a 12 mm deep socket wrench, install the nut.
51201
14.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
32101A
15.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Remove any adhesive remaining in the 6 drive plate and torque converter assembly setting bolts.
| *a | Adhesive |
Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley with SST.
First install the black-colored bolt, and then the remaining 5 silver-colored bolts.
Do not start the engine for at least 1 hour after installing the drive plate and torque converter assembly setting bolts.
11361J
16.INSTALL FLYWHEEL HOUSING UNDER COVER
Install the flywheel housing under cover to the engine assembly.
32942
17.CONNECT OUTLET NO. 1 OIL COOLER HOSE
| *a | View A |
| *b | Lower Side of Vehicle |
Connect the outlet No. 1 oil cooler hose to the outlet No. 1 oil cooler tube and slide the hose clip to secure it as shown in the illustration.
Perform the installation with the hose clip at the correct direction.
32941
18.CONNECT INLET NO. 1 OIL COOLER HOSE
| *a | View A |
| *b | Lower Side of Vehicle |
Connect the inlet No. 1 oil cooler hose to the inlet No. 1 oil cooler tube and slide the hose clip to secure it as shown in the illustration.
Perform the installation with the hose clip at the correct direction.
28100
19.INSTALL STARTER ASSEMBLY
20.INSTALL FRONT DRIVE SHAFT ASSEMBLIES
82121
21.CONNECT ENGINE WIRE
Install the 3 wire harness clamp brackets to the automatic transaxle assembly with the 3 bolts.
Engage the 6 clamps to install the engine wire.
Connect the 3 connectors to the automatic transaxle assembly.
82123
22.CONNECT NO. 3 ENGINE WIRE
Engage the 2 clamps to install the No. 3 engine wire to the engine mounting bracket LH.
Connect the No. 3 engine wire to the automatic transaxle assembly with the bolt.
33820B
23.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
To prevent damage to the transmission control cable assembly and transmission floor shift assembly, connect the automatic transaxle assembly side of the transmission control cable assembly before connecting the transmission floor shift assembly side.
Install the transmission control cable assembly to the transmission control cable support.
| *a | P Position |
| *b | N Position |
Rotate the transmission control shaft lever counterclockwise until it stops, and then from that position rotate it clockwise by 2 notches to set it to the N position.
| *a | Paint Mark |
Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
Make sure that the paint mark on the transmission control cable assembly is aligned with the slit in the No. 1 transmission control cable bracket before installing the clip.
Connect the transmission control cable assembly to the transmission control shaft lever with the nut.
Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the transmission floor shift assembly.
Securely install the end of the transmission control cable assembly to the transmission floor shift assembly.
Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.
24.ADJUST SHIFT LEVER POSITION
58910C
25.INSTALL REAR CONSOLE BOX ASSEMBLY
74410
26.INSTALL BATTERY CARRIER ASSEMBLY
74431
27.INSTALL BATTERY TRAY
28800
28.INSTALL BATTERY
17701
29.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
30.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17735
31.INSTALL AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE
17341T
32.CONNECT NO. 1 AIR HOSE
23820
33.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY
23827A
34.CONNECT NO. 2 FUEL VAPOR FEED HOSE
35.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
36.ADD AUTOMATIC TRANSAXLE FLUID
37.INSPECT AUTOMATIC TRANSAXLE FLUID
38.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK
39.INSPECT SHIFT LEVER POSITION
51441C
40.INSTALL ENGINE UNDER COVER RH
51442C
41.INSTALL ENGINE UNDER COVER LH
42.RESET MEMORY (AT initialization)