12372A
1.INSTALL ENGINE MOUNTING INSULATOR LH
Only perform this procedure when replacement of the engine mounting insulator LH is necessary.
Temporarily tighten the engine mounting insulator LH to the vehicle with the 5 bolts.
Fully tighten the 5 bolts, in the sequence shown in the illustration.
12305
2.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.
Temporarily tighten the engine mounting insulator sub-assembly RH to the vehicle with the 3 bolts.
Fully tighten the 3 bolts, in the sequence shown in the illustration.
3.REMOVE ENGINE STAND
Using a chain block and a sling device, secure the engine assembly.
Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.
Remove the engine stand from the engine assembly.
32101
4.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
Using height adjustment attachments or plate lift attachments, place the engine assembly on a flat, level surface.
Using height adjustment attachments or plate lift attachments, place the engine assembly horizontally.
To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
Using an engine sling device and engine lifter, secure the engine assembly before servicing.
Using SST, hold the crankshaft damper sub-assembly.
| *1 | Front Drive Plate Spacer (Reversible) |
| *2 | Drive Plate and Ring Gear Sub-assembly |
| *3 | Rear Drive Plate Spacer |
|
Engine Side |
|
Transaxle Side |
Install the front drive plate spacer, drive plate and ring gear sub-assembly, and rear drive plate spacer to the crankshaft.
As the drive plate and ring gear sub-assembly and rear drive plate spacer are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.
The front drive plate spacer is reversible.
Clean the 6 bolts and their holes.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads at the end of each of the 6 bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install and uniformly tighten the 6 bolts in several steps, in the sequence shown in the illustration.
Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.
30500
5.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY
| *1 | Crankshaft |
| *2 | Torque Converter Assembly Centerpiece |
|
Clutch Spline Grease |
Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.
Toyota Genuine Clutch Spline Grease or equivalent
Approximately 1 g (0.0353 oz.)
| *1 | Knock Pin |
Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.
Maintain the engine assembly and automatic transaxle assembly in a horizontal position, align the knock pins with each hole in the automatic transaxle assembly and install the automatic transaxle assembly to the engine assembly with the 7 bolts.
When mounting the automatic transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the holes.
When tightening the bolts, be sure that the mating surfaces of the engine assembly and automatic transaxle assembly are in close contact with one another.
Check that the torque converter assembly rotates.
Bolt A: Install from automatic transaxle assembly side
Bolt B: Install from engine assembly side
6.INSTALL WIRE HARNESS CLAMP BRACKET
Install the 2 wire harness clamp brackets to the automatic transaxle assembly with the 2 bolts.
28100
7.INSTALL STARTER ASSEMBLY
11363A
8.INSTALL FLYWHEEL HOUSING SIDE COVER
12321B
9.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
19500D
10.INSTALL NO. 1 IGNITION COIL
17141
11.INSTALL EXHAUST MANIFOLD
25591
12.INSTALL MANIFOLD SUPPORT BRACKET
17167
13.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17111
14.INSTALL INTAKE MANIFOLD WITH THROTTLE BODY WITH MOTOR ASSEMBLY
Install a new intake manifold to head gasket to the intake manifold.
Temporarily tighten the intake manifold with throttle body with motor assembly to the cylinder head sub-assembly with the 3 bolts and 2 nuts.
Tighten the 3 bolts and 2 nuts in the sequence shown in the illustration.
Connect the No. 2 water by-pass hose to the No. 1 water by-pass pipe with the hose clip.
Connect the water by-pass hose to the cylinder head sub-assembly with the hose clip.
Connect the union to connector tube hose to the booster vacuum tube with the hose clip.
15301
15.INSTALL OIL LEVEL DIPSTICK SUB-ASSEMBLY
16502
16.INSTALL WATER FILLER SUB-ASSEMBLY
| *a | View A |
| *b | Paint Mark |
| *c | Top of Vehicle |
Install the water filler sub-assembly to the throttle body with motor assembly with the 2 nuts.
Connect the No. 1 radiator hose to the cylinder head sub-assembly with the hose clip as shown in the illustration.
12261
17.INSTALL VENTILATION HOSE
Install the ventilation hose to the cylinder head cover sub-assembly and intake manifold with the 2 hose clips.
82121
18.INSTALL ENGINE WIRE
Connect the engine wire to the cylinder head sub-assembly with the 2 bolts.
Connect all the engine wire and connectors.
12281A
19.REMOVE NO. 1 ENGINE HANGER
Remove the 2 bolts and 2 No. 1 engine hangers from the cylinder head sub-assembly.
Install the wire harness clamp bracket to the cylinder head sub-assembly with the bolt.
Connect the air fuel ratio sensor wire to the wire harness clamp bracket.
51201
20.TEMPORARILY TIGHTEN FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Temporarily tighten the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the through bolt.
21.INSTALL ENGINE ASSEMBLY WITH AUTOMATIC TRANSAXLE ASSEMBLY
Place height adjustment attachments or plate lift attachments, and then set the engine assembly with automatic transaxle assembly.
Place the height adjustment attachments or plate lift attachments so that the engine assembly with automatic transaxle assembly is level.
As the engine assembly with automatic transaxle assembly is very heavy, be sure to support it securely.
To prevent deformation of the No. 2 oil pan sub-assembly, never set any attachments against the No. 2 oil pan sub-assembly of the engine assembly.
To prevent deformation of the automatic transaxle oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the automatic transaxle assembly.
Operate the engine lifter and lift the engine assembly with automatic transaxle assembly and front suspension crossmember sub-assembly to the position where the engine mounting insulator sub-assembly RH and engine mounting insulator LH can be installed.
Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine is clear of all wiring and hoses.
Connect the engine mounting insulator LH to the engine mounting bracket LH with the through bolt and nut.
Tighten by holding the nut and turning the through bolt.
Connect the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the bolt and 2 nuts.
By inserting SST into the datum holes in the front suspension crossmember sub-assembly RH and LH alternately, tighten the bolts A, B and C on both sides to the specified torque, in several steps.
| *a | Datum Hole | *b | Correct |
| *c | Incorrect | - | - |
|
Front of the Vehicle | - | - |
Insert SST into the datum hole vertically.
If impossible to insert SST vertically, loosen all bolts and then insert SST again.
Tighten the engine moving control rod bolt.
45025D
22.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY
45209
23.CONNECT STEERING SLIDING YOKE SUB-ASSEMBLY
45259A
24.INSTALL COLUMN HOLE COVER SILENCER SHEET
32101A
25.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
11361J
26.INSTALL FLYWHEEL HOUSING UNDER COVER
43420
27.INSTALL FRONT DRIVE SHAFT ASSEMBLY
33820B
28.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
29.ADJUST SHIFT LEVER POSITION
17410
30.INSTALL FRONT EXHAUST PIPE ASSEMBLY
57533B
31.INSTALL FRONT FLOOR CENTER BRACE
58910C
32.INSTALL REAR CONSOLE BOX ASSEMBLY
82121
33.CONNECT ENGINE WIRE
Connect the engine wire to the automatic transaxle assembly with the bolt.
Engage the 2 clamps to connect the engine wire to the engine mounting bracket LH.
| *a | Top of the Vehicle |
Pass the engine wire through the hole to the outside of the engine room and engage the grommet to the vehicle as shown in the illustration.
Engage the clamp to connect the engine wire to the wire harness clamp bracket.
Engage the 2 clamps to connect the engine wire to the wire harness clamp bracket and vehicle.
Connect the 3 connectors as shown in the illustration.
Engage the 2 claws to connect the engine wire to the engine room relay block.
Install the nut to the engine room relay block.
Connect the connector to the engine room relay block.
Engage the clamp to connect the engine wire to the vehicle.
Install the relay block cover to the engine room relay block.
55550
34.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
88320
35.INSTALL COOLER COMPRESSOR ASSEMBLY
88712
36.CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE
88711
37.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
16361A
38.INSTALL FAN AND GENERATOR V BELT
16361A
39.ADJUST FAN AND GENERATOR V BELT
44772
40.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE
Connect the check valve to connector tube hose to the booster vacuum tube with the hose clip.
32942
41.CONNECT OUTLET NO. 1 OIL COOLER HOSE
32941
42.CONNECT INLET NO. 1 OIL COOLER HOSE
23901
43.CONNECT FUEL TUBE SUB-ASSEMBLY
23842A
44.INSTALL EFI FUEL PIPE CLAMP
87246
45.CONNECT OUTLET HEATER WATER HOSE
| *a | View A |
| *b | Paint Mark |
| *c | Top of Vehicle |
| *d | Front of Vehicle |
Connect the outlet heater water hose to the No. 1 water by-pass pipe with the hose clip as shown in the illustration.
87245
46.CONNECT INLET HEATER WATER HOSE
| *a | View A |
| *b | Paint Mark |
| *c | Top of Vehicle |
| *d | Front of Vehicle |
Connect the inlet heater water hose to the cylinder head sub-assembly with the hose clip as shown in the illustration.
16572D
47.CONNECT NO. 2 RADIATOR HOSE
| *a | View A |
| *b | Paint Mark |
| *c | Top of Vehicle |
| *d | Right Side of Vehicle |
Connect the No. 2 radiator hose to the water inlet with the hose clip as shown in the illustration.
16573B
48.CONNECT NO. 3 RADIATOR HOSE
| *a | View A |
| *b | Paint Mark |
| *c | Top of Vehicle |
| *d | Right Side of Vehicle |
Connect the No. 3 radiator hose to the water filler sub-assembly with the hose clip as shown in the illustration.
49.CONNECT RADIATOR RESERVOIR TANK HOSE
17361M
50.INSTALL AIR TUBE
Install the air tube to the cylinder head cover sub-assembly with the bolt.
74410
51.INSTALL BATTERY CARRIER ASSEMBLY
Install the battery carrier assembly to the engine mounting insulator LH and vehicle with the 5 bolts.
Engage the 6 clamps to connect the engine wire to the battery carrier assembly.
74431
52.INSTALL BATTERY TRAY
Install the battery tray to the battery carrier assembly.
28800
53.INSTALL BATTERY
| *1 | Battery Clamp Bolt |
| *2 | Battery Carrier |
| *3 | Engine Room Main Wire |
| *4 | Engine Wire |
Install the battery to the battery tray.
Install the battery clamp sub-assembly bolt and battery clamp sub-assembly to the battery carrier assembly with the 2 nuts.
Engage the hook of the battery clamp bolt to the notch of the battery carrier assembly.
Engage the 2 claws to connect the engine room main wire to the engine wire.
Connect the engine room main wire with engine wire to the positive (+) battery terminal with the nut.
Install the terminal cover to the positive (+) battery terminal.
23820
54.INSTALL FUEL VAPOR FEED HOSE ASSEMBLY
Install the fuel vapor feed hose assembly to the cylinder head cover sub-assembly and fuel tube with the 2 hose clips.
55.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly to the air cleaner bracket with the 3 bolts.
Engage the clamp to connect the engine wire to the air cleaner case sub-assembly.
17801
56.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.
17735
57.INSTALL AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE
17341T
58.CONNECT NO. 1 AIR HOSE
23827A
59.CONNECT NO. 2 FUEL VAPOR FEED HOSE
23820
60.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY
61.INSTALL FRONT WHEELS
16361A
62.INSPECT FAN AND GENERATOR V BELT
63.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
64.ADD ENGINE COOLANT
65.INSPECT ENGINE OIL LEVEL
66.ADD AUTOMATIC TRANSAXLE FLUID
67.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
68.WARM UP ENGINE
69.INSPECT FOR REFRIGERANT LEAK
70.INSPECT AUTOMATIC TRANSAXLE FLUID
71.INSPECT FOR COOLANT LEAK
72.INSPECT FOR ENGINE OIL LEAK
73.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK
74.INSPECT FOR FUEL LEAK
75.INSPECT FOR EXHAUST GAS LEAK
76.INSPECT SHIFT LEVER POSITION
77.INSPECT IGNITION TIMING
78.INSPECT ENGINE IDLING SPEED
79.INSPECT CO/HC
80.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
51441C
81.INSTALL ENGINE UNDER COVER RH
Install the engine under cover RH to the vehicle with the 2 bolts and 2 screws.
51442C
82.INSTALL ENGINE UNDER COVER LH
Install the engine under cover LH to the vehicle with the 3 bolts and 5 screws.
11212
83.INSTALL NO. 2 CYLINDER HEAD COVER
84.INSPECT SPEED SENSOR SIGNAL