Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
43420G
1.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING
Install a new front drive shaft hole snap ring to the front drive shaft assembly.
43420
2.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
for CVT:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine CVT Fluid FE.
for U340E Automatic Transaxle:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine ATF WS.
for U441E Automatic Transaxle:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine ATF Type T-IV.
for Manual Transaxle:
Coat the splines of the front drive inboard joint assembly with gear oil.
Coat the lip of the front drive shaft oil seal LH with MP grease.
Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.
Face the end gap of the front drive shaft hole snap ring downward.
Do not damage the front drive shaft oil seal LH.
Do not damage the front axle inboard joint boot.
Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring.
Confirm whether the front drive shaft assembly LH is securely driven in by checking the reaction force and sound.
43410
3.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH
Perform the same procedure as for the LH side.
43498A
4.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
for CVT with 1NR-FE:
Click hereEngine / Hybrid System>1NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>INSTALLATION
for Manual Transaxle with 1NR-FE and 2NR-FE:
Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for Manual Transaxle)>INSTALLATION
5.INSTALL FRONT AXLE ASSEMBLY
| *a | Matchmark |
Align the matchmarks and install the front axle assembly to the front drive shaft assembly LH.
Be careful not to damage the front axle outboard joint boot.
48069
6.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY
48819A
7.INSTALL FRONT STABILIZER BOLT
45047
8.INSTALL TIE ROD END SUB-ASSEMBLY
47313A
9.INSTALL FRONT FLEXIBLE HOSE (w/ ABS)
Install the front speed sensor wire and front flexible hose to the front shock absorber assembly and body with the 2 bolts.
Install the front speed sensor wire and front flexible hose without twisting them.
Install the front speed sensor wire first and then the front flexible hose.
47313A
10.INSTALL FRONT FLEXIBLE HOSE (w/o ABS)
Install the front flexible hose to the front shock absorber assembly with the bolt.
Install the front flexible hose without twisting it.
43502H
11.INSTALL FRONT AXLE SHAFT NUT
Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.
Be sure to perform this work even when using a new front drive shaft assembly.
Keep the threaded parts free of oil and foreign matter.
Using a 30 mm deep socket wrench, install the front axle shaft nut.
Keep depressing the brake pedal to prevent the front drive shaft assembly from rotating.
Using a chisel and a hammer, stake the front axle shaft nut.
12.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)
for K312:
Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE FLUID>ADJUSTMENT
for K411:
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE FLUID>ADJUSTMENT
13.ADD AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)
for U340E:
Click hereDrivetrain>U340E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>INSTALLATION
for U441E:
Click hereDrivetrain>U441E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>INSTALLATION
14.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)
15.INSPECT AUTOMATIC TRANSAXLE FLUID (for Automatic Transaxle)
for U340E:
Click hereDrivetrain>U340E AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>INSTALLATION
16.INSPECT MANUAL TRANSAXLE OIL (for Manual Transaxle)
17.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK (for CVT)
18.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK (for Automatic Transaxle)
19.INSPECT FOR MANUAL TRANSAXLE OIL LEAK (for Manual Transaxle)
51441C
20.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)
for 2NR-FE:
Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>INSTALLATION
51442C
21.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)
for 2NR-FE:
Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>INSTALLATION
51405A
22.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)
for Manual Transaxle:
Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for Manual Transaxle)>INSTALLATION
51451A
23.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)
for Manual Transaxle:
Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for Manual Transaxle)>INSTALLATION
24.INSTALL FRONT WHEELS
25.ADJUST FRONT WHEEL ALIGNMENT
26.CHECK FOR SPEED SENSOR SIGNAL (w/ ABS)