Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2016.07–2016.10
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the speedometer sensor*1 or brake actuator assembly (skid control ECU)*2.

*1: w/o ABS

*2: w/ ABS


WIRING DIAGRAM

C352186E05
1.438,0.333 1.896,0.531 0.458,0.198 10 false SP1 3.583,1.167 4.042,1.365 0.458,0.198 10 false SI 1.406,2.563 1.865,2.76 0.458,0.198 10 false SPD 1.396,4.042 1.854,4.24 0.458,0.198 10 false SPD 1.406,5.25 1.865,5.448 0.458,0.198 10 false SPD 1.813,0.042 2.583,0.229 0.771,0.188 10 false 22*9, *10 3.521,0.948 3.979,1.146 0.458,0.198 10 false 3 1.854,2.469 2.313,2.667 0.458,0.198 10 false 7 1.844,3.948 2.302,4.146 0.458,0.198 10 false 5 1.844,5.146 2.302,5.344 0.458,0.198 10 false 2 0.49,1.365 2.135,1.865 1.646,0.5 10 false Brake Actuator Assembly (Skid Control ECU) 0.49,0.698 0.99,1.719 0.5,1.021 10 false A35*9 A47*10 A48*11 A49*12 2.99,1.875 4.635,2.375 1.646,0.5 10 false Speedometer Sensor*2 2.99,1.708 4.635,2.208 1.646,0.5 10 false B22 0.542,3.135 2.104,3.667 1.563,0.531 10 false Certification ECU (Smart Key ECU Assembly)*3 0.542,2.969 2.104,3.5 1.563,0.531 10 false F43 0.729,4.604 2.292,5.135 1.563,0.531 10 false Body Computer*1 0.729,4.438 2.292,4.969 1.563,0.531 10 false F52 0.313,5.813 2.229,6.333 1.917,0.521 10 false Power Steering ECU Assembly 0.313,5.646 1.625,6.177 1.313,0.531 10 false F12 5.26,0.208 5.719,0.406 0.458,0.198 10 false 34 5.573,0.302 6.031,0.5 0.458,0.198 10 false SI 5.26,2.469 5.719,2.667 0.458,0.198 10 false 35 5.573,2.563 6.031,2.76 0.458,0.198 10 false +S 5.396,3.031 5.854,3.229 0.458,0.198 10 false F38 5.396,3.198 6.615,3.688 1.219,0.49 10 false Combination Meter Assembly 5.594,5.24 6.052,5.438 0.458,0.198 10 false SPD 4.969,4.781 5.49,5.385 0.521,0.604 10 false 30*4 2.958,5.135 3.417,5.333 0.458,0.198 10 false 20 2.958,3.948 3.417,4.146 0.458,0.198 10 false 18 2.979,2.469 3.438,2.667 0.458,0.198 10 false 19 4.219,2.469 4.677,2.667 0.458,0.198 10 false 21 4.219,5.135 4.677,5.333 0.458,0.198 10 false 17 5.563,5.646 6.198,6.229 0.635,0.583 10 false F81*4 5.563,6.146 6.021,6.344 0.458,0.198 10 false ECM 0.083,6.167 2.208,6.74 2.125,0.573 10 false *1: w/ Wireless Door Lock Control System 2.896,5.635 5.802,5.833 2.906,0.198 10 false F66 2.896,5.802 5.802,6 2.906,0.198 10 false No. 4 Junction Connector 0.083,6.833 3,7.083 2.917,0.25 10 false *2: w/o ABS 0.083,7.167 3,7.417 2.917,0.25 10 false *3: w/ Smart Entry and Start System 4.969,5.125 5.813,5.729 0.844,0.604 10 false 23*7,*8 5.563,5.813 7.01,6.052 1.448,0.24 10 false F82*5, *6 5.563,5.979 6.719,6.156 1.156,0.177 10 false F130*7, *8 4.958,4.948 6.531,5.333 1.573,0.385 10 false 18*5, *6 0.104,7.906 2.365,8.323 2.26,0.417 10 false *5: for 1NZ-FE 2.573,6.875 4.563,7.208 1.99,0.333 10 false *7: for 1NR-FE 2.583,7.229 4.573,7.563 1.99,0.333 10 false *8: for 2NR-FE 2.594,7.573 4.635,8.073 2.042,0.5 10 false *9: w/ ABS without VSC except LHD and CVT 4.979,6.813 6.771,7.375 1.792,0.563 10 false *10: w/ ABS without VSC for LHD and CVT 4.979,7.448 6.771,7.958 1.792,0.51 10 false *11: w/ VSC except CVT 0.083,7.531 2.5,7.781 2.417,0.25 10 false *4: for 2NZ-FE with Manual Transaxle 2.573,6.188 4.427,6.625 1.854,0.438 10 false *6: for 2NZ-FE except Manual Transaxle 4.99,7.792 6.979,8.125 1.99,0.333 10 false *12: w/ VSC with CVT 1.813,0.219 2.583,0.406 0.771,0.188 10 false 11*11, *12

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (INPUT VOLTAGE)
a.
E219772C05
1.438,0.125 1.927,0.417 0.49,0.292 2.271,1.219 2.083,1.677 true 1.552,0.188 1.833,0.344 0.281,0.156 10 false F38 0.198,0.094 0.406,0.25 0.208,0.156 10 false *a 2,1.677 2.292,1.833 0.292,0.156 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F38-35 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

2.SYSTEM CHECK

NG

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 JUNCTION CONNECTOR)
2.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ ABS A
w/o ABS B



A

3.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

B

5.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
3.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Disconnect the brake actuator assembly connector.

C352274C01
4.99,0.292 5.5,0.542 0.51,0.25 1.667,0.292 2.177,0.542 0.51,0.25 1.667,2.5 2.177,2.75 0.51,0.25 4.99,2.5 5.5,2.75 0.51,0.25 2.625,2.156 2.24,1.406 true 5.854,2.156 5.479,1.406 true 5.594,3.385 6.51,3.74 true 2.344,3.385 3.281,3.74 true 0.75,0.26 1.167,0.542 0.417,0.281 12 false *A 4.021,0.26 4.417,0.542 0.396,0.281 12 false *B 0.75,2.469 1.156,2.719 0.406,0.25 12 false *C 4.01,2.469 4.385,2.76 0.375,0.292 12 false *D 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.802,0.323 2.292,0.573 0.49,0.25 10 false A35 1.792,2.542 2.281,2.792 0.49,0.25 10 false A48 5.115,0.333 5.604,0.583 0.49,0.25 10 false A47 5.125,2.542 5.615,2.792 0.49,0.25 10 false A49 2.688,2.083 3.177,2.333 0.49,0.25 10 false SP1 5.917,2.083 6.406,2.333 0.49,0.25 10 false SP1 6.583,3.667 7.073,3.917 0.49,0.25 10 false SP1 3.344,3.667 3.833,3.917 0.49,0.25 10 false SP1
*A w/ ABS without VSC except LHD and CVT *B w/ ABS without VSC for LHD and CVT
*C w/ VSC except CVT *D w/ VSC with CVT
*a Front view of wire harness connector
(to Brake Actuator Assembly)
- -



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A35-22 (SP1) - Body ground*1 Ignition switch ON 11 to 14 V
A47-22 (SP1) - Body ground*2 Ignition switch ON 11 to 14 V
A48-11 (SP1) - Body ground*3 Ignition switch ON 11 to 14 V
A49-11 (SP1) - Body ground*4 Ignition switch ON 11 to 14 V


*1: w/ ABS without VSC except LHD and CVT

*2: w/ ABS without VSC for LHD and CVT

*3: w/ VSC except CVT

*4: w/ VSC with CVT



c.

Reconnect the brake actuator assembly connector.


Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
4.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E270889C01
1.5,0.417 1.917,0.667 0.417,0.25 0.917,2.083 1.333,1.5 true 0,0 0.313,0.156 0.313,0.156 10 false *a 1.583,0.458 2.042,0.656 0.458,0.198 10 false F38 0.833,2.115 1.292,2.313 0.458,0.198 10 false SI 2.927,3.719 3.385,3.917 0.458,0.198 10 false GND 1.229,4 1.688,4.198 0.458,0.198 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F38-34 (SI) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn the wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch ON, wheel being rotated

OK:

The waveform is displayed as shown in the illustration.


HINT:

As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

5.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.
E231160C01
1.5,0.344 1.917,0.594 0.417,0.25 1.969,1.156 2.333,1.75 true 0,0 0.313,0.156 0.313,0.156 10 false *a 1.583,0.385 2.042,0.583 0.458,0.198 10 false B22 2.271,1.771 2.583,1.969 0.313,0.198 10 false SI
*a Front view of wire harness connector
(to Speedometer Sensor)


Disconnect the speedometer sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B22-3 (SI) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the speedometer sensor connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SPEEDOMETER SENSOR)
6.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E270889C01
1.5,0.417 1.917,0.667 0.417,0.25 0.917,2.083 1.333,1.5 true 0,0 0.313,0.156 0.313,0.156 10 false *a 1.583,0.458 2.042,0.656 0.458,0.198 10 false F38 0.833,2.115 1.292,2.313 0.458,0.198 10 false SI 2.927,3.719 3.385,3.917 0.458,0.198 10 false GND 1.229,4 1.688,4.198 0.458,0.198 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F38-34 (SI) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn the wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.



Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch ON, wheel being rotated

OK:

The waveform is displayed as shown in the illustration.


HINT:

As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Result:
Result Proceed to
OK A
NG (Transaxle (C50)) B
NG (Transaxle (C54)) C



A

REPLACE COMBINATION METER ASSEMBLY

B

C

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the A35 brake actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-34 (SI) - A35-22 (SP1) Always Below 1 Ω
F38-34 (SI) or A35-22 (SP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SPEEDOMETER SENSOR)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the B22 speedometer sensor connector.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-34 (SI) - B22-3 (SI) Always Below 1 Ω
F38-34 (SI) or B22-3 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 4 JUNCTION CONNECTOR)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the F66 No. 4 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-35 (+S) - F66-21 Always Below 1 Ω
F38-35 (+S) or F66-21 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.SYSTEM CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ Wireless Door Lock Control System A
w/o Wireless Door Lock Control System B



A

11.INSPECT BODY COMPUTER

B

12.SYSTEM CHECK
11.INSPECT BODY COMPUTER
a.
E270875C21
1.563,0.167 1.969,0.427 0.406,0.26 0,0 0.313,0.156 0.313,0.156 10 false *a 1.635,0.208 2.094,0.406 0.458,0.198 10 false F66
*a Front view of wire harness connector
(to No. 4 Junction Connector)


Disconnect the No. 4 junction connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F66-18 - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

14.INSPECT ECM

NG

16.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - BODY COMPUTER)
12.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ Smart Entry and Start System A
w/o Smart Entry and Start System B



A

13.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

14.INSPECT ECM
13.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
E270875C06
1.563,0.167 1.969,0.427 0.406,0.26 0,0 0.313,0.156 0.313,0.156 10 false *a 1.635,0.208 2.094,0.406 0.458,0.198 10 false F66
*a Front view of wire harness connector
(to No. 4 Junction Connector)


Disconnect the No. 4 junction connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F66-19 - Body ground Ignition switch ON 4.5 to 14 V



c.

Reconnect the No. 4 junction connector.


Result:
Proceed to
OK
NG



OK

14.INSPECT ECM

NG

17.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
14.INSPECT ECM
a.
E270875C08
1.531,0.167 1.927,0.427 0.396,0.26 0,0 0.313,0.156 0.313,0.156 10 false *a 1.615,0.208 2.073,0.406 0.458,0.198 10 false F66
*a Front view of wire harness connector
(to No. 4 Junction Connector)


Disconnect the No. 4 junction connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F66-17 - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

15.INSPECT POWER STEERING ECU ASSEMBLY

NG

18.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - ECM)
15.INSPECT POWER STEERING ECU ASSEMBLY
a.
E270875C04
1.531,0.167 1.927,0.427 0.396,0.26 0,0 0.313,0.156 0.313,0.156 10 false *a 1.615,0.208 2.073,0.406 0.458,0.198 10 false F66
*a Front view of wire harness connector
(to No. 4 Junction Connector)


Disconnect the No. 4 junction connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F66-20 - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 JUNCTION CONNECTOR

NG

19.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
16.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - BODY COMPUTER)
a.

Disconnect the F66 No. 4 junction connector.


b.

Disconnect the F52 body computer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F66-18 - F52-5 (SPD) Always Below 1 Ω
F66-18 - F52-5 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE BODY COMPUTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F66 No. 4 junction connector.


b.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F66-19 - F43-7 (SPD) Always Below 1 Ω
F66-19 or F43-7 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - ECM)
a.

Disconnect the F66 No. 4 junction connector.


b.

Disconnect the F81*1 F82*2, *3 or F130*4, *5 ECM connector.

*1: for 2NZ-FE with Manual Transaxle

*2: for 1NZ-FE

*3: for 2NZ-FE except Manual Transaxle

*4: for 1NR-FE

*5: for 2NR-FE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F66-17 - F81-30 (SPD)*1 Always Below 1 Ω
F66-17 - F82-18 (SPD)*2, *3 Always Below 1 Ω
F66-17 - F130-23 (SPD)*4, *5 Always Below 1 Ω
F66-17 or F81-30(SPD),*1 - Body ground Always 10 kΩ or higher
F66-17 or F82-18(SPD)*2, *3 - Body ground Always 10 kΩ or higher
F66-17 or F130-23(SPD)*4, *5 - Body ground Always 10 kΩ or higher


*1: for 2NZ-FE with Manual Transaxle

*2: for 1NZ-FE

*3: for 2NZ-FE except Manual Transaxle

*4: for 1NR-FE

*5: for 2NR-FE



Result:
Result Proceed to
OK (for 1NZ-FE) A
OK (for 2NZ-FE) B
OK (for 1NR-FE) C
OK (for 2NR-FE) D
NG E



A

B

C

D

E

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (NO. 4 JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the F66 No. 4 junction connector.


b.

Disconnect the F12 power steering ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F66-20 - F12-2 (SPD) Always Below 1 Ω
F66-20 or F12-2 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR