Home › Engine / Hybrid System › 2NR-FE ENGINE CONTROL › SFI SYSTEM › 2016.10–2017.10
RM30M0E _51 Engine / Hybrid System _053304 2NR-FE ENGINE CONTROL _0258353 SFI SYSTEM J

2NR-FE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A254573E17
4.875,3.25 5.25,3.417 0.375,0.167 10 false ECM 5.417,1.875 6.396,2.104 0.979,0.229 10 false Microprocessor 4.469,0.927 6.292,1.135 1.823,0.208 10 false 5 V Constant Voltage Circuit 0.333,2.76 2.583,3.198 2.25,0.438 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 0.333,1.844 2.625,2.427 2.292,0.583 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have IC) 1.281,0.896 2.656,1.115 1.375,0.219 10 false from EFI NO. 3 Fuse 1.646,1.25 2.625,1.51 0.979,0.26 10 false from EFI Relay 2.865,1.135 3.448,1.313 0.583,0.177 10 false +B, +B2 2.938,0.802 3.396,1.021 0.458,0.219 10 false BATT 3.229,2.073 3.552,2.292 0.323,0.219 10 false VC 4.125,2.927 4.323,3.135 0.198,0.208 10 false R

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the ignition switch is turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

·

VC Output Circuit

A356980E04
0.365,0.594 0.823,0.792 0.458,0.198 10 false S1 0.365,0.781 2.156,0.979 1.792,0.198 10 false Vacuum Sensor Assembly 2.552,0.656 3.01,0.854 0.458,0.198 10 false VC 2.583,1.469 3.042,1.667 0.458,0.198 10 false E2 2.563,1.063 3.021,1.26 0.458,0.198 10 false PB 2.938,0.552 3.104,0.802 0.167,0.25 10 false 3 2.938,0.958 3.104,1.208 0.167,0.25 10 false 2 2.917,1.375 3.083,1.625 0.167,0.25 10 false 1 5.281,0.469 5.49,0.719 0.208,0.25 10 false 27 5.281,0.875 5.49,1.125 0.208,0.25 10 false 26 5.271,1.292 5.479,1.542 0.208,0.25 10 false 35 5.198,0.646 5.615,0.813 0.417,0.167 10 false F130 5.208,1.052 5.625,1.219 0.417,0.167 10 false F130 5.198,1.458 5.615,1.625 0.417,0.167 10 false F130 5.646,0.563 6.229,0.729 0.583,0.167 10 false VCPB 5.667,1.083 6,1.333 0.333,0.25 10 false PB 5.667,1.406 6.083,1.573 0.417,0.167 10 false EPB 0.354,2.177 0.813,2.375 0.458,0.198 10 false B17 0.365,2.365 1.906,2.813 1.542,0.448 10 false Throttle Body with Motor Assembly 2.563,2.188 3.021,2.385 0.458,0.198 10 false VC 2.49,2.583 2.917,2.802 0.427,0.219 10 false VTA 2.417,3.021 2.875,3.219 0.458,0.198 10 false VTA2 2.583,3.427 3.042,3.625 0.458,0.198 10 false E2 2.917,2.104 3.083,2.354 0.167,0.25 10 false 5 2.927,2.5 3.094,2.75 0.167,0.25 10 false 6 2.938,2.917 3.104,3.167 0.167,0.25 10 false 4 2.938,3.344 3.104,3.594 0.167,0.25 10 false 3 5.281,2.021 5.49,2.271 0.208,0.25 9 false 29 5.26,2.438 5.469,2.688 0.208,0.25 9 false 30 5.271,2.854 5.479,3.104 0.208,0.25 9 false 18 5.271,3.271 5.479,3.521 0.208,0.25 9 false 28 5.24,2.188 5.656,2.354 0.417,0.167 10 false B46 5.24,2.594 5.656,2.76 0.417,0.167 10 false B46 5.25,3.021 5.667,3.188 0.417,0.167 10 false B46 5.229,3.427 5.646,3.594 0.417,0.167 10 false B46 5.667,2.115 6.25,2.281 0.583,0.167 10 false VCTA 5.667,2.625 6.25,2.792 0.583,0.167 10 false VTA1 5.667,3.031 6.25,3.198 0.583,0.167 10 false VTA2 5.667,3.354 6.25,3.521 0.583,0.167 10 false ETA 0.271,4.167 0.729,4.365 0.458,0.198 10 false B35 0.26,4.354 2.052,4.552 1.792,0.198 10 false Crank Position Sensor 2.552,4.135 3.01,4.333 0.458,0.198 10 false VC 2.469,4.563 2.927,4.76 0.458,0.198 10 false NE+ 2.49,4.979 2.948,5.177 0.458,0.198 10 false NE- 2.938,4.052 3.104,4.302 0.167,0.25 10 false 3 2.938,4.479 3.104,4.729 0.167,0.25 10 false 1 2.948,4.875 3.115,5.125 0.167,0.25 10 false 2 5.26,3.969 5.469,4.219 0.208,0.25 9 false 33 5.281,4.396 5.49,4.646 0.208,0.25 9 false 27 5.26,4.813 5.469,5.063 0.208,0.25 9 false 34 5.229,4.146 5.646,4.313 0.417,0.167 10 false B46 5.24,4.563 5.656,4.729 0.417,0.167 10 false B46 5.229,4.979 5.646,5.146 0.417,0.167 10 false B46 5.667,4.063 6.25,4.229 0.583,0.167 10 false VCNE 5.667,4.573 6.125,4.771 0.458,0.198 10 false NE+ 5.688,4.875 6.146,5.073 0.458,0.198 10 false NE- 5.271,5.51 5.479,5.76 0.208,0.25 9 false 21 5.271,5.927 5.479,6.177 0.208,0.25 9 false 23 5.271,6.344 5.479,6.594 0.208,0.25 9 false 22 5.229,5.688 5.646,5.854 0.417,0.167 10 false B46 5.229,6.104 5.646,6.271 0.417,0.167 10 false B46 5.24,6.51 5.656,6.677 0.417,0.167 10 false B46 0.271,5.677 0.729,5.875 0.458,0.198 10 false B45 0.26,5.844 1.927,6.26 1.667,0.417 10 false Camshaft Position Sensor (for Intake Camshaft) 2.552,5.667 3.01,5.865 0.458,0.198 10 false VC 2.448,6.083 2.906,6.281 0.458,0.198 10 false VVI+ 2.479,6.5 2.917,6.698 0.438,0.198 10 false VVI- 2.917,5.583 3.083,5.833 0.167,0.25 10 false 3 2.917,6 3.083,6.25 0.167,0.25 10 false 1 2.927,6.417 3.094,6.667 0.167,0.25 10 false 2 5.677,5.573 6.26,5.74 0.583,0.167 10 false VCV1 5.677,6.104 6.135,6.302 0.458,0.198 10 false VV1+ 5.677,6.417 6.135,6.615 0.458,0.198 10 false VV1- 0.271,7.167 0.729,7.365 0.458,0.198 10 false B44 0.271,7.313 1.896,7.729 1.625,0.417 10 false Camshaft Position Sensor (for Exhaust Camshaft) 2.479,7.208 2.938,7.406 0.458,0.198 10 false VC2 2.375,7.583 2.833,7.823 0.458,0.24 10 false VVE+ 2.396,8.031 2.854,8.229 0.458,0.198 10 false VVE- 2.938,7.115 3.104,7.365 0.167,0.25 10 false 3 2.906,7.51 3.073,7.76 0.167,0.25 10 false 1 2.927,7.938 3.094,8.188 0.167,0.25 10 false 2 5.26,7.042 5.469,7.292 0.208,0.25 9 false 31 5.271,7.458 5.479,7.708 0.208,0.25 9 false 24 5.271,7.875 5.479,8.125 0.208,0.25 9 false 32 5.229,7.219 5.646,7.385 0.417,0.167 10 false B46 5.24,7.635 5.656,7.802 0.417,0.167 10 false B46 5.229,8.052 5.646,8.219 0.417,0.167 10 false B46 5.656,7.125 6.24,7.292 0.583,0.167 10 false VCE1 5.667,7.646 6.25,7.813 0.583,0.167 10 false EV1+ 5.667,7.948 6.25,8.115 0.583,0.167 10 false EV1- 6.063,8.583 6.99,8.833 0.927,0.25 10 false ECM

A356981E20
0.354,0.677 0.813,0.875 0.458,0.198 10 false B49 0.344,0.865 1.885,1.115 1.542,0.25 10 false Oil Pressure Sensor*1 0.344,2.344 0.802,2.542 0.458,0.198 10 false A33*2 0.344,2.708 1.948,3.208 1.604,0.5 10 false Accelerator Pedal Sensor Assembly 0.365,5.167 0.823,5.365 0.458,0.198 10 false F117 0.344,5.344 2.281,5.573 1.938,0.229 10 false Atmospheric Pressure Sensor 2.563,0.719 3.021,0.917 0.458,0.198 10 false VC 2.479,1.135 2.938,1.333 0.458,0.198 10 false PTO 2.583,1.563 3.042,1.76 0.458,0.198 10 false E2 2.365,2.313 2.906,2.51 0.542,0.198 10 false VCPA 2.375,2.719 2.917,2.917 0.542,0.198 10 false VCP2 2.458,3.146 3,3.344 0.542,0.198 10 false VPA 2.385,3.583 2.917,3.75 0.531,0.167 10 false VPA2 2.448,3.958 2.99,4.156 0.542,0.198 10 false EPA 2.406,4.375 2.948,4.573 0.542,0.198 10 false EPA2 2.563,5.135 3.021,5.333 0.458,0.198 10 false VC 2.573,5.552 3.031,5.75 0.458,0.198 10 false PB 2.583,5.958 3.042,6.156 0.458,0.198 10 false E2 2.927,0.615 3.094,0.813 0.167,0.198 10 false 3 2.938,1.021 3.104,1.219 0.167,0.198 10 false 2 2.927,1.448 3.094,1.646 0.167,0.198 10 false 1 2.917,2.625 3.083,2.823 0.167,0.198 10 false 1 2.917,2.198 3.083,2.396 0.167,0.198 10 false 4 2.938,3.042 3.104,3.24 0.167,0.198 10 false 6 2.938,3.469 3.104,3.667 0.167,0.198 10 false 3 2.948,3.875 3.115,4.073 0.167,0.198 10 false 5 2.927,4.281 3.094,4.479 0.167,0.198 10 false 2 2.927,5.031 3.094,5.229 0.167,0.198 10 false 3 2.927,5.458 3.094,5.656 0.167,0.198 10 false 2 2.927,5.875 3.094,6.073 0.167,0.198 10 false 1 5.281,0.552 5.656,0.719 0.375,0.167 10 false 32 5.208,0.729 5.667,0.917 0.458,0.188 10 false F130 5.271,0.948 5.646,1.115 0.375,0.167 10 false 24 5.271,1.365 5.604,1.531 0.333,0.167 10 false 31 5.188,1.135 5.667,1.333 0.479,0.198 10 false F130 5.177,1.552 5.635,1.719 0.458,0.167 10 false F130 5.698,0.615 6.333,0.833 0.635,0.219 10 false VCPT*1 5.667,1.448 6.333,1.667 0.667,0.219 10 false EPTO*1 5.667,1.146 6.25,1.333 0.583,0.188 10 false PTO*1 5.688,2.198 6.188,2.365 0.5,0.167 10 false VCPA 5.677,2.615 6.177,2.781 0.5,0.167 10 false VCP2 5.26,2.135 5.594,2.302 0.333,0.167 10 false 20 5.198,2.313 5.656,2.479 0.458,0.167 10 false F131 5.26,2.552 5.594,2.719 0.333,0.167 10 false 22 5.271,2.958 5.604,3.125 0.333,0.167 10 false 26 5.292,3.375 5.625,3.542 0.333,0.167 10 false 28 5.281,3.781 5.615,3.948 0.333,0.167 10 false 27 5.281,4.208 5.615,4.375 0.333,0.167 10 false 29 5.188,2.729 5.646,2.896 0.458,0.167 10 false F131 5.208,3.146 5.667,3.313 0.458,0.167 10 false F131 5.208,3.552 5.667,3.719 0.458,0.167 10 false F131 5.198,3.969 5.615,4.135 0.417,0.167 10 false F131 5.208,4.375 5.698,4.542 0.49,0.167 10 false F131 5.677,3.146 6.219,3.344 0.542,0.198 10 false VPA 5.667,3.573 6.208,3.771 0.542,0.198 10 false VPA2 5.656,3.865 6.198,4.063 0.542,0.198 10 false EPA 5.646,4.292 6.188,4.49 0.542,0.198 10 false EPA2 5.271,4.958 5.604,5.125 0.333,0.167 10 false 33 5.271,5.365 5.604,5.531 0.333,0.167 10 false 25 5.271,5.781 5.604,5.948 0.333,0.167 10 false 34 5.198,5.146 5.573,5.313 0.375,0.167 10 false F130 5.208,5.552 5.583,5.719 0.375,0.167 10 false F130 5.208,5.969 5.583,6.135 0.375,0.167 10 false F130 5.656,5.052 6.198,5.25 0.542,0.198 10 false VHAC 5.656,5.563 6.198,5.76 0.542,0.198 10 false HAC 5.656,5.865 6.198,6.063 0.542,0.198 10 false EHAC 6.063,6.521 6.604,6.719 0.542,0.198 10 false ECM 3.938,0.615 4.188,0.781 0.25,0.167 10 false *1 3.948,1.031 4.198,1.198 0.25,0.167 10 false *1 3.938,1.458 4.188,1.625 0.25,0.167 10 false *1 0.344,2.531 0.802,2.729 0.458,0.198 10 false F85*3 0.167,6.417 1.167,6.615 1,0.198 10 false *1: for CVT 1.24,6.417 2.406,6.615 1.167,0.198 10 false *2: for TMT Made 2.667,6.417 4.167,6.667 1.5,0.25 10 false *3: for TMMIN Made


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

The Data List item "Engine and ECT" can be checked.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ECM)
a.

Turn the ignition switch to ON.


b.
A342760C04
2.5,0.417 3,0.667 0.5,0.25 2.094,2.583 2.594,2.833 0.5,0.25 0.49,0.417 0.99,0.667 0.5,0.25 0.583,2.583 1.083,2.833 0.5,0.25 2.354,1.833 2.875,1.021 true 3.25,1.833 2.938,1.021 true 1.948,4 2.469,3.188 true 2.969,4 2.531,3.188 true 0.344,4 0.865,3.188 true 0.281,1.833 0.802,1.021 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 0.25,0.25 0.667,0.49 0.417,0.24 12 false *A 0.25,2.417 0.625,2.656 0.375,0.24 12 false *B 2.604,0.448 3.219,0.646 0.615,0.198 10 false F131 2.177,2.615 2.792,2.813 0.615,0.198 10 false F131 1.813,4.01 2.427,4.208 0.615,0.198 10 false +B2 2.906,4.01 3.344,4.208 0.438,0.198 10 false +B 0.625,0.448 1.24,0.646 0.615,0.198 10 false B46 0.708,2.615 1.323,2.813 0.615,0.198 10 false B46 0.229,4.01 0.844,4.208 0.615,0.198 10 false E1 0.188,1.844 0.802,2.042 0.615,0.198 10 false E1 2.229,1.833 2.844,2.031 0.615,0.198 10 false +B2 3.167,1.833 3.417,2 0.25,0.167 10 false +B
*A for CVT
*B for Manual Transaxle
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F131-1 (+B) - B46-3 (E1) Ignition switch ON 11 to 14 V
F131-2 (+B2) - B46-3 (E1) Ignition switch ON 11 to 14 V


HINT:

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.



Result:
Proceed to
OK
NG



OK

3.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (VACUUM SENSOR ASSEMBLY)

NG

CHECK ECU POWER SOURCE CIRCUIT

3.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (VACUUM SENSOR ASSEMBLY)
a.

Disconnect the S1 vacuum sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

The Data List item "Engine and ECT" can be checked.


Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

4.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (THROTTLE POSITION SENSOR)

B

4.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the B17 throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

The Data List item "Engine and ECT" can be checked.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B


HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



A

5.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (CRANKSHAFT POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

5.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the B35 crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

The Data List item "Engine and ECT" can be checked.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

6.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the B45 camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

The Data List item "Engine and ECT" can be checked.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

7.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the B44 camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

The Data List item "Engine and ECT" can be checked.



Result:
Result Proceed to
Communication is not possible (for CVT) A
Communication is not possible (for Manual Transaxle) B
Communication is possible C



A

8.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (OIL PRESSURE SENSOR)

B

9.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (ACCELERATOR PEDAL SENSOR ASSEMBLY)

C

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

8.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (OIL PRESSURE SENSOR)
a.

Disconnect the B49 oil pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

The Data List item "Engine and ECT" can be checked.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (ACCELERATOR PEDAL SENSOR ASSEMBLY)

B

REPLACE OIL PRESSURE SENSOR

9.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the A33 accelerator pedal sensor aseembly connector (for TMT Made).


b.

Disconnect the F85 accelerator pedal sensor assembly connector (for TMMIN Made).


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Check the communication between the GTS and ECM.

HINT:

The Data List item "Engine and ECT" can be checked.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (ATMOSPHERIC PRESSURE SENSOR)

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

10.CHECK COMMUNICATION BETWEEN THE GTS AND ECM (ATMOSPHERIC PRESSURE SENSOR)
a.

Disconnect the F117 atmospheric pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

The Data List item "Engine and ECT" can be checked.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

11.CHECK HARNESS AND CONNECTOR

B

11.CHECK HARNESS AND CONNECTOR
a.

Disconnect the S1 vacuum sensor assembly connector.


b.

Disconnect the B17 throttle body with motor assembly connector.


c.

Disconnect the B35 crankshaft position sensor connector.


d.

Disconnect the B45 camshaft position sensor (for intake camshaft) connector.


e.

Disconnect the B44 camshaft position sensor (for exhaust camshaft) connector.


f.

Disconnect the B49 oil pressure sensor connector (for CVT).


g.

Disconnect the A33 accelerator pedal sensor assembly connector (for TMT Made).


h.

Disconnect the F85 accelerator pedal sensor assembly connector (for TMMIN Made).


i.

Disconnect the F117 atmospheric pressure sensor connector.


j.

Disconnect the B46, F130 and F131 ECM connectors.


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-27 (VCPB) - Body ground and other terminals Always 10 kΩ or higher
B46-29 (VCTA) - Body ground and other terminals Always 10 kΩ or higher
B46-33 (VCNE) - Body ground and other terminals Always 10 kΩ or higher
B46-21 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
B46-31 (VCE1) - Body ground and other terminals Always 10 kΩ or higher
F130-32 (VCPT)*1 - Body ground and other terminals Always 10 kΩ or higher
F131-20 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
F131-22 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
F130-33 (VHAC) - Body ground and other terminals Always 10 kΩ or higher


*1: for CVT



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR