Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2016.10–2017.10
RM30M0E _55 Steering _017104 STEERING COLUMN _0090116 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45186 4.REMOVE NO. 2 STEERING WHEEL LOWER COVER

Hide 45130 5.REMOVE HORN BUTTON ASSEMBLY (w/ Airbag System)

Hide 45130 6.REMOVE HORN BUTTON ASSEMBLY (w/o Airbag System)

Hide 45100 7.REMOVE STEERING WHEEL ASSEMBLY

Hide 45289A 8.REMOVE STEERING COLUMN COVER SUPPORT (w/ Smart Entry and Start System)

a.
C284674

Disengage the 4 claws to remove the steering column cover support.


Hide 45287 9.REMOVE LOWER STEERING COLUMN COVER

a.
C286512

Remove the 3 screws.


b.

Release the tilt lever.


c.

Disengage the 3 claws to remove the lower steering column cover.


Hide 45286B 10.REMOVE UPPER STEERING COLUMN COVER

a.
C287884

Disengage the claw to remove the upper steering column cover.


Hide 11.REMOVE COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE

a.

Disconnect all the connectors from the combination switch assembly with spiral cable.


b.
C286513C01
0.375,0.781 0.49,0.646 false 0.385,0.208 0.552,0.396 false 0.24,0.135 0.427,0.281 0.188,0.146 10 false *1 0.24,0.719 0.417,0.885 0.177,0.167 10 true *a
*1 Clamp
*a Claw


Use pliers to hold the clamp and raise the claw with a screwdriver. Remove the combination switch assembly with spiral cable from the steering column assembly.


Hide 55606 12.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55432B 13.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)

Hide 55432B 14.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)

Hide 45259A 15.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C286514

Fold back the floor carpet.


b.

Remove the 2 clips and column hole cover silencer sheet.


Hide 45209 16.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C286515C01
1.781,1.531 2.156,1.448 2.156,1.448 1.771,1.448 true 2.198,1.354 2.427,1.521 0.229,0.167 10 true *a 1.74,0.635 1.896,0.802 0.156,0.167 10 true A 2.01,1.125 2.167,1.292 0.156,0.167 10 true B
*a Matchmark


Put matchmarks on the steering sliding yoke sub-assembly and steering link assembly.


b.

Loosen bolt A.


c.

Remove bolt B to separate the steering sliding yoke sub-assembly from the steering link assembly.


Hide 55106 17.REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for LHD)

Hide 55106 18.REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for RHD)

Hide 19.REMOVE STEERING COLUMN ASSEMBLY

a.

Disconnect all the connectors and disengage all the wire harness clamps from the steering column assembly.

NOTICE:

Do not pull the wire harness.



b.
C355117

Disconnect the 2 connectors from the power steering ECU assembly.


c.

Disengage the wire harness clamp to separate the wire harness from the instrument panel reinforcement assembly.


d.
C287506

Remove the bolt, 2 nuts and steering column assembly from the instrument panel reinforcement assembly.


Hide 45879A 20.REMOVE BREAK AWAY CAPSULE

a.

Remove the 2 break away capsules from the steering column assembly.