Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY › 2016.10–2017.10
RM30M0E _52 Drivetrain _017092 DRIVE SHAFT / PROPELLER SHAFT _0092752 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEELS

Hide 51442C 2.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51441C 3.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51451A 4.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 6.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

·
·

Hide 43502H 8.REMOVE FRONT AXLE SHAFT NUT

a.
C282323E01
2.281,1.25 2.656,0.531 true 2.708,0.427 3.167,0.625 0.458,0.198 10 false SST

Using SST and a hammer, release the staked part of the front axle shaft nut.

SST
09930-00010  

NOTICE:

Loosen the staked part of the nut completely, otherwise the threads of the front drive shaft assembly may be damaged.



b.

Using a 30 mm deep socket wrench, remove the front axle shaft nut.

HINT:

Keep depressing the brake pedal to prevent the front drive shaft assembly from rotating.



Hide 47313A 9.SEPARATE FRONT FLEXIBLE HOSE (w/ ABS)

a.
C295467

Remove the 2 bolts to separate the front flexible hose and front speed sensor wire from the front shock absorber assembly and body.


Hide 47313A 10.SEPARATE FRONT FLEXIBLE HOSE (w/o ABS)

a.
C283560

Remove the bolt to separate the front flexible hose from the front shock absorber assembly.


Hide 45047 11.SEPARATE TIE ROD END SUB-ASSEMBLY

Hide 48819A 12.REMOVE FRONT STABILIZER BOLT

Hide 48069 13.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 14.SEPARATE FRONT AXLE ASSEMBLY

a.
C283835C01
2.771,1.021 3.094,0.729 3.094,0.729 2.927,1.313 true 3.125,0.615 3.365,0.844 0.24,0.229 10 false *a
*a Matchmark


Put matchmarks on the front drive shaft assembly and front axle hub sub-assembly.


b.

Using a plastic hammer, tap the end of the front drive shaft assembly and separate the fitting between the front drive shaft assembly and front axle assembly.

NOTICE:

Be careful not to damage the front drive shaft assembly.


HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.



Hide 43498A 15.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

Hide 43420 16.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

a.
C282241E01
1.906,0.583 0.99,0.427 0.99,0.427 1.604,0.656 true 0.698,0.344 1.052,0.552 0.354,0.208 10 false SST

Using SST, remove the front drive shaft assembly LH from the transaxle.

SST
09520-01010  
09520-24010  (09520-32040)

NOTICE:
·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly LH.




Hide 43410 17.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

a.
C287118

Using a brass bar and a hammer, remove the front drive shaft assembly RH from the transaxle.

NOTICE:
·

Do not damage the front drive shaft oil seal RH.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly RH.




Hide 43420G 18.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

a.
C283836

Using a screwdriver, remove the front drive shaft hole snap ring from the front drive shaft assembly.


Hide 19.FIX FRONT AXLE ASSEMBLY

HINT:

The hub bearing could be damaged if it is subjected to the vehicle's full weight, such as when moving the vehicle with the front drive shaft assembly removed. If it is absolutely necessary to place the vehicle's full weight on the hub bearing, first support it with SST.


C285252E01
1.51,1.104 0.938,1.031 0.938,1.031 1.563,0.958 false 0.646,0.938 1.104,1.135 0.458,0.198 10 false SST

SST
09608-16042  (09608-02021, 09608-02041)