Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE › 2017.10–2018.01
RM30M0E _54 Brake _017102 PARKING BRAKE _0092773 PARKING BRAKE CABLE A

PARKING BRAKE  PARKING BRAKE CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side (No. 3 parking brake cable assembly) and RH side (No. 2 parking brake cable assembly).

·

The following procedure is for the LH side (No. 3 parking brake cable assembly).



PROCEDURE

Hide 46430 1.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Rear Drum Brake)

a.

Install the No. 3 parking brake cable assembly to the rear axle beam assembly with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Install the No. 3 parking brake cable assembly to the body with the 3 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


c.

Engage the clamp to install a new parking brake cable clamp.


d.

Install the No. 3 parking brake cable assembly to the body.


e.

Connect the No. 3 parking brake cable assembly to the backing plate with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 46430 2.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Rear Disc Brake)

a.

Install the No. 3 parking brake cable assembly to the rear axle beam assembly with the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Install the No. 3 parking brake cable assembly to the body with the 3 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


c.

Engage the clamp to install a new parking brake cable clamp.


d.

Install the No. 3 parking brake cable assembly to the body.


e.

Engage the clip to install the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.

NOTICE:

Be sure to engage the clip to the rear disc brake cylinder assembly.



f.

Connect the No. 3 parking brake cable assembly to the rear disc brake cylinder assembly.


Hide 89516D 3.INSTALL SKID CONTROL SENSOR WIRE

a.

Install the skid control sensor wire to the rear axle beam assembly with the nut.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 4.INSTALL REAR BRAKE STRUT KIT (for Rear Drum Brake)

Hide 5.INSPECT REAR DRUM BRAKE (for Rear Drum Brake)

Hide 42403 6.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)

Hide 7.ADJUST REAR DRUM BRAKE SHOE CLEARANCE (for Rear Drum Brake)

a.
C233136C01
0,0 3.427,0 false
V100135

Expand


Temporarily install the 2 wheel nuts.


b.

Remove the shoe adjusting hole plug.


c.

Turn the adjuster to expand the shoe until the drum locks.


d.
C233134C08
0,0 3.427,0 false
V100135

Contract


Hold the rear brake automatic adjust lever away from the adjuster, and contract the rear brake shoe by turning the adjust bolt using another screwdriver until the drum can rotate smoothly.

Standard:

12 notches



e.

Install the shoe adjusting hole plug.


f.

Remove the 2 wheel nuts.


Hide 8.INSTALL REAR WHEEL (for Rear Drum Brake)

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 77641A 9.INSTALL NO. 1 FUEL TANK PROTECTOR (for RH Side)

Hide 58156 10.INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR (for RH Side)

Hide 17410 11.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for RH Side)

Hide 57533B 12.INSTALL FRONT FLOOR CENTER BRACE (for RH Side)

Hide 51405A 13.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (for RH Side w/ Metal Type Under Cover)

Hide 51451A 14.INSTALL CENTER ENGINE UNDER COVER (for RH Side w/ Metal Type Under Cover)

Hide 46430 15.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.

Engage the claw and 2 guides to install the parking brake cable end stopper to the parking brake equalizer.


b.

Connect the No. 3 parking brake cable assembly to the parking brake equalizer.


Hide 16.ADJUST PARKING BRAKE LEVER TRAVEL

Hide 58910C 17.INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Type)

Hide 58910C 18.INSTALL REAR CONSOLE BOX ASSEMBLY (for Integrated Type)