Home › Drivetrain › K312 CVT › PARK / NEUTRAL POSITION SWITCH › 2017.10–2018.01
RM30M0E _52 Drivetrain _052969 K312 CVT _0259995 PARK / NEUTRAL POSITION SWITCH A

K312 CVT  PARK / NEUTRAL POSITION SWITCH  INSTALLATION  


PROCEDURE

Hide 84540 1.INSTALL PARK/NEUTRAL POSITION SWITCH

a.

Temporarily install the park/neutral position switch to the continuously variable transaxle assembly with the 2 bolts.


b.

Install the lock nut and lock plate to the park/neutral position switch.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


c.
C151661N08
2.896,0.656 3.052,0.833 0.156,0.177 10 true P 2.573,0.135 2.75,0.313 0.177,0.177 10 true N

Temporarily install the control shaft lever.


d.

Turn the control shaft lever clockwise until it stops, and then from that position turn it counterclockwise by 2 notches to set it to the N position.


e.

Remove the control shaft lever.


f.
C154976C07
2.042,1.198 1.531,0.177 true 2.208,1.969 1.719,1.188 true 1.375,0.083 1.646,0.313 0.271,0.229 10 false *a 2.198,1.969 2.427,2.167 0.229,0.198 10 false *b
*a Neutral Basic Line
*b Protrusion


Align the protrusion with the neutral basic line.


g.

Hold the park/neutral position switch in that position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


h.
C304846

Using a screwdriver, bend down the tabs of the lock plate.


i.

Install the control shaft lever to the continuously variable transaxle assembly with the nut and washer.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


j.

Connect the park/neutral position switch connector.


Hide 33820B 2.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

To prevent damage to the transmission control cable assembly and transmission floor shift assembly, connect the continuously variable transaxle assembly side of the transmission control cable assembly before connecting the transmission floor shift assembly side.


a.

Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


b.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Before connecting the transmission control cable assembly, check that the park/neutral position switch and shift lever are in neutral.



c.

Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Securely install the end of the transmission control cable assembly to the transmission floor shift assembly.

·

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.




Hide 17701 6.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 7.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17880 9.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 12.ADJUST SHIFT LEVER POSITION

Hide 58810J 13.INSTALL CONSOLE BOX ASSEMBLY (for TMT Made)

Hide 58839A 14.INSTALL CONSOLE BOX HOLE COVER (for TMT Made)

Hide 58916 15.INSTALL BOX BOTTOM MAT (for TMT Made)

Hide 58912C 16.INSTALL NO. 2 SIDE BOX PANEL (for TMT Made)

Hide 58911A 17.INSTALL NO. 1 SIDE BOX PANEL (for TMT Made)

Hide 58817A 18.INSTALL NO. 2 FRONT CONSOLE BOX INSERT (for TMT Made)

Hide 58816D 19.INSTALL NO. 1 FRONT CONSOLE BOX INSERT (for TMT Made)

Hide 58910C 20.INSTALL REAR CONSOLE BOX ASSEMBLY (for Integrated Type)

Hide 58910C 21.INSTALL REAR CONSOLE BOX ASSEMBLY (for Separate Type)

Hide 84540 22.INSPECT PARK/NEUTRAL POSITION SWITCH

Hide 84540 23.ADJUST PARK/NEUTRAL POSITION SWITCH