When the ignition switch is ON, the combination meter assembly receives signals from the front seat inner belt assembly (Driver Side). When the seat belt is unfastened, the combination meter assembly flashes the driver side seat belt warning light in the combination meter assembly. When the seat belt is fastened, the combination meter assembly stops flashing the driver side seat belt warning light.
for TMMIN Made
for TMT Made
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for TMMIN Made | A |
| for TMT Made | B |
A
B
Connect the GTS DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt | Front seat belt warning light | OFF or ON | Confirm that the vehicle is stopped with the engine idling |
| Tester Display |
|---|
| Driver Side Seat Belt |
Driver side seat belt warning light condition can be switched by Active Test.
| Result |
|---|
| OK |
| NG |
OK
NG
Remove the front seat inner belt assembly LH.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL
Inspect the front seat inner belt assembly LH.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the F29 front seat inner belt assembly LH connector.
Disconnect the 2N driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F29-3 - 2N-2 | Always | Below 1 Ω |
| F29-3 or 2N-2 - Body ground | Always | 10 kΩ or higher |
| F29-2 - Body ground | Always | Below 1 Ω |
Reconnect the 2N driver side junction block assembly connector.
Reconnect the F29 front seat inner belt assembly LH connector.
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the F38 combination meter assembly connector.
Disconnect the 2M driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-24 (L) - 2M-4 | Always | Below 1 Ω |
| F38-24 (L) or 2M-4 - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
Remove the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
Remove the body compter.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2N-2 - 2M-4 | Always | Below 1 Ω |
| 2N-2 or 2M-4 - Body ground | Always | 10 kΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Connect the GTS DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Driver Side Seat Belt | Front seat belt warning light | OFF or ON | Confirm that the vehicle is stopped with the engine idling |
| Tester Display |
|---|
| Driver Side Seat Belt |
Front seat belt warning light condition can be switched by Active Test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Driver Side Seatbelt Buckle Switch | Front seat belt buckle switch (Driver Side) | OFF or ON | OFF: Driver seat belt not fastened
ON: Driver seat belt fastened |
- |
| Tester Display |
|---|
| Driver Side Seatbelt Buckle Switch |
ON or OFF appears on the GTS screen according to the driver seat belt condition.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Remove the front seat inner belt assembly LH.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL
Inspect the front seat inner belt assembly LH.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F29 front seat inner belt assembly LH connector.
Disconnect the F38 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F29-3 - F38-5 (BKL) | Always | Below 1 Ω |
| F29-3 or F38-5 (BKL) - Body ground | Always | 10 kΩ or higher |
| F29-2 - Body ground | Always | Below 1 Ω |
Reconnect the F38 combination meter assembly connector.
Reconnect the F29 front seat inner belt assembly LH connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front seat inner belt assembly RH.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL
Inspect the front seat inner belt assembly RH.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F114 front seat inner belt assembly RH connector.
Disconnect the F38 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F114-3 - F38-5 (BKL) | Always | Below 1 Ω |
| F114-3 or F38-5 (BKL) - Body ground | Always | 10 kΩ or higher |
| F114-2 - Body ground | Always | Below 1 Ω |
Reconnect the F38 combination meter assembly connector.
Reconnect the F114 front seat inner belt assembly RH connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG