Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0089807 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver door is opened while the ignition switch is off or ACC. The key reminder warning buzzer is activated when the unlock warning switch signal and the driver door courtesy light switch signal are received by the combination meter assembly.

WIRING DIAGRAM

E384027E01
0.156,0.063 2.917,0.302 2.76,0.24 12 false for TMMIN Made: 1.552,1.74 6.135,1.938 4.583,0.198 10 false Unlock Warning Switch Assembly 1.563,1.583 2.021,1.781 0.458,0.198 10 false F27 1.854,3.646 3.333,4 1.479,0.354 10 false Front Door Courtesy Light Switch Assembly LH 1.865,3.49 2.323,3.688 0.458,0.198 10 false F31 0.177,2.188 3.698,2.385 3.521,0.198 10 false from Map Light Assembly*1 3.865,3.51 5.104,4.083 1.24,0.573 10 false Driver Side Junction Block Assembly 3.125,1.115 3.281,1.313 0.156,0.198 10 false 1 3.146,2.969 3.302,3.167 0.156,0.198 10 false 1 1.844,1.125 2,1.323 0.156,0.198 10 false 2 5.26,5.594 7.125,6.083 1.865,0.49 10 false Combination Meter Assembly 5.26,5.448 5.719,5.646 0.458,0.198 10 false F38 5.74,4.802 6.052,5 0.313,0.198 10 false ED 5.729,3.115 6.042,3.313 0.313,0.198 10 false SW 5.74,1.292 6.354,1.49 0.615,0.198 10 false KSWO 5.406,1.167 5.719,1.365 0.313,0.198 10 false 23 5.5,2.969 5.656,3.167 0.156,0.198 10 false 1 5.417,4.656 5.729,4.854 0.313,0.198 10 false 21 3.854,3.125 4.167,3.323 0.313,0.198 10 false 2N 4.865,3.115 5.177,3.313 0.313,0.198 10 false 2M 3.896,2.896 4.052,3.094 0.156,0.198 10 false 1 4.906,2.917 5.063,3.115 0.156,0.198 10 false 5 0.208,5.854 4.948,6.052 4.74,0.198 10 false *1: w/o Power Door Lock Control 2.979,2.094 3.292,2.292 0.313,0.198 10 false *1

E384026E03
0.281,0.146 2.667,0.385 2.385,0.24 12 false for TMT Made: 2.271,1.385 4.813,1.771 2.542,0.385 10 false Unlock Warning Switch Assembly 2.271,1.188 2.729,1.385 0.458,0.198 10 false F27 2.427,0.813 2.677,1.01 0.25,0.198 10 false 2 3.698,0.802 3.854,1 0.156,0.198 10 false 1 0.073,2.052 3.896,2.25 3.823,0.198 10 false from Map Light Assembly*3 0.563,3.354 3.938,3.615 3.375,0.26 10 false Front Door Courtesy Light Switch Assembly LH*1 0.573,3.167 1.031,3.365 0.458,0.198 10 false F31 0.635,4.375 1.094,4.573 0.458,0.198 10 false F32 0.635,4.563 4.01,4.823 3.375,0.26 10 false Front Door Courtesy Light Switch Assembly RH*2 2.844,2.74 3.156,2.938 0.313,0.198 10 false *1 2.677,1.958 2.99,2.156 0.313,0.198 10 false *3 2.802,3.896 3.115,4.094 0.313,0.198 10 false *2 2.5,2.688 2.656,2.885 0.156,0.198 10 false 1 2.469,3.896 2.625,4.094 0.156,0.198 10 false 1 4.24,3.26 5.49,3.854 1.25,0.594 10 false Driver Side Junction Block Assembly 5.969,0.906 6.427,1.104 0.458,0.198 10 false KSW 5.948,2.906 6.563,3.104 0.615,0.198 10 false DCTY 5.646,0.813 5.958,1.01 0.313,0.198 10 false 27 5.688,2.76 6,2.958 0.313,0.198 10 false 30 5.531,4.479 5.844,4.677 0.313,0.198 10 false 21 4.135,2.875 4.51,3.073 0.375,0.198 10 false 6M 5.365,2.875 5.74,3.073 0.375,0.198 10 false 6M 5.417,2.677 5.573,2.875 0.156,0.198 10 false 4 4.188,2.698 4.344,2.896 0.156,0.198 10 false 2 5.281,5.427 7.125,5.969 1.844,0.542 10 false Combination Meter Assembly 5.292,5.26 5.75,5.458 0.458,0.198 10 false F38 5.938,4.604 6.25,4.802 0.313,0.198 10 false EP 0.344,5.531 2.031,5.729 1.688,0.198 10 false *1: for LHD 0.344,5.865 2.031,6.063 1.688,0.198 10 false *2: for RHD 0.354,6.208 3.875,6.406 3.521,0.198 10 false *3: w/o Power Door Lock

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)
a.

Remove the key from the key cylinder, turn the light control switch on the headlight dimmer switch assembly to the tail position, and open the driver door.

OK:

The light reminder warning buzzer sounds.



HINT:

The key reminder warning system sounds the buzzer built into the combination meter assembly for key reminder warnings. This buzzer is also used for the light reminder warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the lights are still on.


Result:
Result Proceed to
OK A
NG (for TMMIN Made) B
NG (for TMT Made) C



A

2.READ VALUE USING GTS (DRIVER SIDE DOOR)

B

C

2.READ VALUE USING GTS (DRIVER SIDE DOOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Door Driver door courtesy light switch signal CLOSE or OPEN CLOSE: Driver door closed
OPEN: Driver door opened
-
Body Electrical > Combination Meter > Data List
Tester Display
Driver Side Door
50003 122 121

OK:

The GTS indicates ON or OFF according to the driver door condition shown in the table.


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY

B

5.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

C

10.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

for TMMIN Made:

i.

Disconnect the F38 combination meter assembly connector.


ii.

Disconnect the F27 unlock warning switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F27-1 - F38-23 (KSWO) Always Below 1 Ω
F27-2 - Body ground Always Below 1 Ω
F38-21 (ED) - Body ground Always Below 1 Ω
F27-1 or F38-23 (KSWO) - Body ground Always 10 kΩ or higher




b.

for TMT Made:

i.

Disconnect the F38 combination meter assembly connector.


ii.

Disconnect the F27 unlock warning switch assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F27-1 - F38-27 (KSW) Always Below 1 Ω
F27-2 - Body ground Always Below 1 Ω
F38-21 (EP) - Body ground Always Below 1 Ω
F27-1 or F38-27 (KSW) - Body ground Always 10 kΩ or higher




Result:
Result Proceed to
OK (for TMMIN Made) A
OK for (TMT Made) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Remove the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

for TMMIN Made:

i.

Disconnect the F31 front door courtesy light switch assembly LH connector.


ii.

Disconnect the 2N driver side junction block assembly connector


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-1 - 2N-1*1 Map light switch off position Below 1 Ω
F31-1 - 2N-1*2 Always Below 1 Ω
F31-1 or 2N-1 - Body ground*1 Map light switch off position 10 kΩ or higher
F31-1 or 2N-1 - Body ground*2 Always 10 kΩ or higher


*1: w/o Power Door Lock

*2: w/ Power Door Lock




b.

for TMT Made:

i.

Disconnect the F31 front door courtesy light switch assembly LH connector.


ii.

Disconnect the 6M driver side junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-1 - 6M-2*1 Map light switch off position Below 1 Ω
F31-1 - 6M-2*2 Always Below 1 Ω
F31-1 or 6M-2 - Body ground*1 Map light switch off position 10 kΩ or higher
F31-1 or 6M-2 - Body ground*2 Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

for TMMIN Made:

i.

Disconnect the F38 combination meter assembly connector.


ii.

Disconnect the 2M driver side junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-1 (SW) - 2M-5 Always Below 1 Ω
F38-1 (SW) or 2M-5 - Body ground Always 10 kΩ or higher




b.

for TMT Made:

i.

Disconnect the F38 combination meter assembly connector.


ii.

Disconnect the 6M driver side junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-30 (DCTY) - 6M-4 Always Below 1 Ω
F38-30 (DCTY) or 6M-4 - Body ground Always 10 kΩ or higher




Result:
Result Proceed to
OK (for TMMIN Made) A
OK (for TMT Made) B
NG C



A

8.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

B

9.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL


b.

Remove the body computer from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMMIN Made)>REMOVAL


c.
E384041C02
0.802,0.5 1.208,0.74 0.406,0.24 2.271,0.427 2.677,0.667 0.406,0.24 0.135,0.135 0.448,0.333 0.313,0.198 10 false *1 0.927,0.542 1.24,0.74 0.313,0.198 10 false 2N 2.385,0.469 2.698,0.667 0.313,0.198 10 false 2M
*1 Component without harness connected
(Driver Side Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2N-1 - 2M-5 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

9.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL


b.

Remove the body computer from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL


c.
E384040C01
1.5,0.438 1.885,0.667 0.385,0.229 0.177,0.063 0.49,0.26 0.313,0.198 10 false *1 1.594,0.479 1.906,0.677 0.313,0.198 10 false 6M
*1 Component without harness connected
(Driver Side Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6M-2 - 6M-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

10.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Remove the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F32 front door courtesy light switch assembly RH connector.


b.

Disconnect the 6M driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-1 - 6M-2 Always Below 1 Ω
F32-1 or 6M-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the 6M driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-30 - 6M-4 Always Below 1 Ω
F38-30 or 6M-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL


b.

Remove the body computer from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL


c.
E384040C02
1.49,0.427 1.885,0.656 0.396,0.229 0.135,0.146 0.448,0.344 0.313,0.198 10 false *1 1.594,0.448 1.906,0.646 0.313,0.198 10 false 6M
*1 Component without harness connected
(Driver Side Junction Block Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6M-2 - 6M-4 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY