Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR(for TMT Made) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017122 DOOR / HATCH _0335794 FRONT DOOR(for TMT Made) A

DOOR / HATCH  FRONT DOOR(for TMT Made)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the RH side.



PROCEDURE

Hide 67837B 1.INSTALL FRONT DOOR DUST PROOF SEAL

a.
B488415

Engage the 3 claws to install the 3 front door dust proof seals.


Hide 75792 2.INSTALL DOOR WINDOW FRAME MOULDING CLIP

a.
B488414

Engage the claw to install the door window frame moulding clip.


Hide 67862 3.INSTALL FRONT DOOR WEATHERSTRIP

a.
B369423E01
0.667,1.417 0.313,1.115 true 0.74,1.406 0.906,1.594 0.167,0.188 10 true A

Engage the clip A and 14 clips and install the front door weatherstrip.


b.

Install the clip.


Hide 68610 4.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door check assembly.


b.
B346730C01
0.729,0.229 0.938,0.438 0.208,0.208 10 true *a 2.135,0.229 2.333,0.427 0.198,0.198 10 true *b
*a Door Panel Side
*b Body Panel Side


Install the front door check assembly onto the door panel side with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



d.

Install the front door check assembly onto the body panel side with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 67001A 5.INSTALL FRONT DOOR PANEL CUSHION

a.
B346729

Install the 2 front door panel cushions.


Hide 69312 6.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B488416C01
2.833,2.281 2.594,1.979 true 1.406,1.969 1.688,2.073 false 2.406,1.844 2.719,2 0.313,0.156 10 false *a 1.188,1.844 1.5,2 0.313,0.156 10 false *a
*a Snap Ring


Install the front door lock open rod to the front door outside handle frame sub-assembly.


b.

Engage the snap ring as shown in the illustration.


Hide 69202A 7.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (for Driver Side)

a.

Apply MP grease to the sliding parts of the front door outside handle frame sub-assembly.


b.
B488410C01
2.417,1.625 2.74,1.396 false 0.448,1.531 0.771,1.302 true 1.698,1.646 1.531,1.375 true 2.229,1.521 2.542,1.677 0.313,0.156 10 false *a 1.74,1.552 2.052,1.708 0.313,0.156 10 false *b 0.271,1.417 0.583,1.573 0.313,0.156 10 false *a
*a Grommet
*b Guide


w/ Smart Entry and Start System:

i.

Engage the guide and 2 clamps.


ii.
B488417C01
0.417,0.292 0.26,0.813 true 2.125,0.479 1.792,0.906 true 1.302,1.802 1.375,1.573 true 0.458,0.156 0.667,0.323 0.208,0.167 10 false *a 1.208,1.802 1.521,1.958 0.313,0.156 10 false *b 2.177,0.365 2.49,0.521 0.313,0.156 10 false *c
*a Guide
*b Clamp
*c Grommet


Engage the grommet and guide to install the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.


iii.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


iv.

Engage the clamp.



c.

w/o Smart Entry and Start System:

i.
B470667C01
1.833,1.063 2.354,1.396 true 0.417,0.271 0.25,0.833 true 2.427,1.302 2.74,1.458 0.313,0.156 10 false *a 0.458,0.156 0.771,0.313 0.313,0.156 10 false *b
*a Grommet
*b Guide


Engage the guide and grommet to install the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.


ii.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)



Hide 69202A 8.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (for Front Passenger Side)

a.

Apply MP grease to the sliding parts of the front door outside handle frame sub-assembly.


b.
B470666C02
1.708,1.323 1.573,1.073 true 3.115,1.25 3.021,1.01 true 1.771,1.229 2.083,1.427 0.313,0.198 10 false *a 3.156,1.167 3.333,1.344 0.177,0.177 10 true *b
*a Grommet
*b Guide


Engage the grommet and guide to install the front door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242E 9.INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B488408

Engage the 2 guides to install the front door outside handle rear pad.


Hide 69241H 10.INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B488407

Engage the 2 claws and guide to install the front door outside handle front pad.


Hide 69220 11.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

a.
B488411

Install the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.


b.

w/ Smart Entry and Start System:

i.
B488412

Connect the connector.


ii.
B488418

Engage the claws to close the cover.



Hide 69220 12.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side)

a.
B488419

Install the front door outside handle assembly in the direction indicated by the arrow as shown in the illustration.


Hide 69320 13.INSTALL FRONT DOOR LOCK ASSEMBLY

Hide 69217F 14.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (w/ Lock Cylinder)

a.
B470649

Engage the guide and claw to install the front door outside handle cover to the lock cylinder.


b.

Apply MP grease to the sliding parts of the lock cylinder.


c.
B488401C01
2.479,1.917 2.813,1.917 false 2.281,1.813 2.594,1.969 0.313,0.156 10 false *1
*1 Hole Plug


Install the front door outside handle cover with lock cylinder.

HINT:

Make sure that the front door lock cylinder is inserted into the front door lock assembly.



d.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


e.

Install the hole plug.


Hide 69217F 15.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (w/o Lock Cylinder)

a.
B488402C01
0.625,2.063 0.958,2.063 false 1.01,1.969 1.323,2.125 0.313,0.156 10 false *1
*1 Hole Plug


Engage the 2 claws and install the front door outside handle cover.


b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Install the hole plug.


Hide 67404F 16.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B346718

Engage the guide and install the front door rear lower frame sub-assembly.


b.

Install the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 67924 17.INSTALL FRONT DOOR NO. 2 STIFFENER CUSHION

a.
B346717C01
1.979,0.833 2.313,0.833 true 2.375,0.74 2.688,0.938 0.313,0.198 10 true *a
*a Double-sided Tape


Install a new front door No. 2 stiffener cushion with the 2 bolts.

HINT:

Peel off the backing paper from the double-sided tape before installing the front door No. 2 stiffener cushion.


Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


b.

Apply thorough pressure to the sections with double-sided tape.


Hide 69820 18.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.
B488400C03
2.031,0.354 1.719,0.135 true 1.521,0.01 1.833,0.167 0.313,0.156 10 false *a 1.698,0.979 1.865,1.146 0.167,0.167 10 false 1 2.885,0.052 3.052,0.219 0.167,0.167 10 false 2 2.813,1.167 2.979,1.333 0.167,0.167 10 true 3 1.688,0.427 1.854,0.594 0.167,0.167 10 false 4
*a Temporary Bolt


Temporarily install the temporary bolt to the front door window regulator assembly.


c.

Temporarily install the front door window regulator assembly.


d.

Install the front door window regulator assembly with the 5 bolts and tighten the temporary bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



e.

Connect the connector.


Hide 67664C 19.INSTALL DOOR FRAME GARNISH

a.
B356959

Engage the clamp and install a new door frame garnish.


Hide 68151D 20.INSTALL FRONT DOOR GLASS RUN

a.
B488399

Install the front door glass run.


Hide 68102 21.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

Connect the power window regulator master switch assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Move the front door glass sub-assembly so that the door glass bolt holes can be seen.


d.

Disconnect the cable from the negative (-) battery terminal.


e.

Disconnect the power window regulator master switch assembly.


f.
B346740E01
1.896,0.073 2.354,0.271 0.458,0.198 10 false (1) 0.823,0.167 1.281,0.365 0.458,0.198 10 false (2)

Insert the front door glass sub-assembly into the front door panel as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the front door glass sub-assembly.



g.
B346714

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not damage the front door glass sub-assembly.



Hide 67832 22.INSTALL FRONT DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the front door panel.


b.

Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.


c.
B488420C01
0.49,0.406 0.625,0.323 false 2.99,0.948 2.927,0.771 false 0.656,0.208 0.969,0.365 0.313,0.156 10 false *a 2.917,0.917 3.229,1.073 0.313,0.156 10 false *a
*a Reference Point
V100143

Butyl Tape


Install the front door service hole cover according to the reference points on the front door panel.

NOTICE:

Securely install the front door service hole cover, taking care to prevent wrinkles and air bubbles.



Hide 68172A 23.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B488397

Install the front door glass inner weatherstrip.


Hide 75922M 24.INSTALL NO. 1 BLACK OUT TAPE (w/ Black Out Tape)

Hide 75756C 25.INSTALL FRONT DOOR WINDOW FRAME REAR MOULDING

Hide 68210C 26.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 87940 27.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

Hide 86160 28.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 69206B 29.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B488396

Engage the 4 guides and install the front door inside handle sub-assembly to the front door trim board sub-assembly.


Hide 67602 30.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B488395C01
1.26,0.646 1.052,0.323 false 0.854,1.188 1.177,0.906 true 0.875,0.219 1.188,0.375 0.313,0.156 10 false *1 0.646,1.115 0.958,1.271 0.313,0.156 10 false *2
*1 Front door inside locking cable assembly
*2 Front door lock remote control cable assembly


Engage the 2 guides and connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door trim board sub-assembly.


b.
B488394

Engage the 5 claws and the guide.


c.

Engage the 8 clips and install the front door trim board sub-assembly.


d.
B488393

Install the 3 screws.


e.
B488421

Engage the claw and close the door inside handle bezel plug.


Hide 74232 31.INSTALL FRONT ARMREST BASE UPPER PANEL

a.

for Driver Side:

i.
B488390

Connect the 2 connectors.



b.

for Front Passenger Side:

i.
B488390

Connect the connector.



c.
B488389

Engage the 8 claws, 2 clips and 4 guides to install the front armrest base upper panel.


Hide 74220 32.INSTALL FRONT ARMREST ASSEMBLY

a.
B488388C01
2.677,1.104 2.479,1.292 false 2.719,0.969 3.031,1.125 0.313,0.156 10 false *1
*1 Retainer


Engage the retainer.


b.
B488387

Engage the 8 claws, 3 clips and 4 guides to install the front armrest assembly.


Hide 67492A 33.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

a.
B346702

Engage the 2 clips and install the front door lower frame bracket garnish.


Hide 34.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (for Hatchback).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 35.INITIALIZE POWER WINDOW CONTROL SYSTEM