Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR(for TMT Made) › 2017.10–2018.01
RM30M0E _59 Vehicle Exterior _017122 DOOR / HATCH _0335795 REAR DOOR(for TMT Made) A

DOOR / HATCH  REAR DOOR(for TMT Made)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for both the RH and LH sides.

·

The procedure described below is for the RH side.



PROCEDURE

Hide 67837C 1.INSTALL REAR DOOR DUST PROOF SEAL

a.
B488442

Engage the 3 claws to install the 3 rear door dust proof seals.


Hide 75792 2.INSTALL DOOR WINDOW FRAME MOULDING CLIP

a.
B488441

Engage the claw to install the door window frame moulding clip.


Hide 67872 3.INSTALL REAR DOOR WEATHERSTRIP

a.
B346771

Engage the clamp and the 16 clips, and install the rear door weatherstrip.


Hide 68630 4.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door check assembly.


b.
B346770C01
0.875,0.26 1.188,0.458 0.313,0.198 10 false *a 2.74,0.26 3.052,0.458 0.313,0.198 10 false *b
*a Door Panel Side
*b Body Panel Side


Install the rear door check assembly onto the door panel side with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



d.

Install the rear door check assembly onto the body panel side with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 69204A 5.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B488443C01
0.469,1.208 0.323,1.719 true 1.719,0.677 2.073,1.125 true 1.542,0.542 1.854,0.698 0.313,0.156 10 false *a 0.24,1.729 0.552,1.885 0.313,0.156 10 false *b
*a Grommet
*b Guide


Engage the guide and the grommet, and install the rear door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242G 6.INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD

a.
B488439

Engage the 2 guides to install the rear door outside handle rear pad.


Hide 69241G 7.INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD

a.
B488438

Engage the 2 claws to guide to install the rear door outside handle front pad.


Hide 69240 8.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B488444

Install the rear door outside handle assembly in the direction indicated by the arrow as shown in the illustration.


Hide 69227L 9.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.
B488436

Engage the guide and 2 claws to install the rear door outside handle cover.


b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 67836D 10.INSTALL REAR DOOR LOCK CHILD PROTECTION COVER

a.
B488435

Install the rear door lock child protection cover.


Hide 69340 11.INSTALL REAR DOOR LOCK ASSEMBLY

Hide 68189 12.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP

a.
B346763

Install the rear door quarter window weatherstrip to the rear door quarter window glass.


Hide 68124B 13.INSTALL REAR DOOR QUARTER WINDOW GLASS

a.
B346778

Install the rear door quarter window glass with rear door quarter window weatherstrip in the direction indicated by the arrow as shown in the illustration.


Hide 69840A 14.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/ Power Window)

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.
B488434C03
0.948,0.792 1.281,0.792 true 0.698,0.677 0.917,0.844 0.219,0.167 10 true *a 2.021,1.76 2.188,1.927 0.167,0.167 10 false 1 1.792,0.042 1.917,0.208 0.125,0.167 10 true 2 2.677,1.208 2.844,1.375 0.167,0.167 10 true 3 1.042,0.385 1.208,0.552 0.167,0.167 10 true 4
*a Temporary Bolt


Temporarily install the temporary bolt to the rear door window regulator assembly.


c.

Temporarily install the rear door window regulator assembly.


d.

Install the rear door window regulator assembly with the 3 bolts and tighten the temporary bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



e.

Connect the connector.


Hide 69840A 15.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY (w/o Power Window)

a.
B347103

Install the rear door window regulator assembly with the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68104 16.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.

Apply MP grease to the sliding surface between the rear door glass sub-assembly and the rear door window regulator sub-assembly.


b.
B346779

Insert the rear door glass sub-assembly into the rear door panel in the direction indicated by the arrow as shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



c.
B346780

Install the rear door glass sub-assembly to the rear door window regulator assembly as shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



Hide 67408H 17.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B346758

Install the screw.

NOTICE:

Make sure to return the rear door weatherstrip to its original condition after performing this step.


HINT:

Peel back the rear door weatherstrip to install the screw.



b.

Install the rear door window division bar sub-assembly with the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)

NOTICE:

When installing rear door window division bar sub-assembly, do not allow the rear door quarter window glass to fall.



Hide 67842E 18.INSTALL REAR DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the rear door panel.


b.

Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.


c.
B488445C01
0.333,0.458 0.458,0.344 false 2.865,0.469 2.76,0.365 false 0.49,0.208 0.802,0.406 0.313,0.198 10 false *a 2.594,0.25 2.906,0.448 0.313,0.198 10 false *a
*a Reference Point


Install the rear door service hole cover according to the reference points on the rear door panel.

NOTICE:

Securely install the rear door service hole cover, taking care to prevent wrinkles and air bubbles.



d.

Connect each connector.


Hide 67674A 19.INSTALL REAR DOOR FRAME GARNISH

a.
B346755

Engage the clamp and install a new rear door frame garnish.


Hide 68152C 20.INSTALL REAR DOOR GLASS RUN

a.
B483989

Install the rear door glass run.


Hide 68174A 21.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

a.
B483988

Install the rear door glass inner weatherstrip.


Hide 75924 22.INSTALL NO. 2 BLACK OUT TAPE (for Sedan)

Hide 75924 23.INSTALL NO. 2 BLACK OUT TAPE (for Hatchback)

Hide 75762A 24.INSTALL REAR DOOR WINDOW FRAME FRONT MOULDING

Hide 68230C 25.INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 86160B 26.INSTALL REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

Hide 69206C 27.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B488396

Engage the 4 guides and install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.


Hide 67604 28.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B488430C01
1.031,0.688 0.792,0.313 true 0.958,0.979 0.75,1.24 false 0.594,0.198 0.802,0.365 0.208,0.167 10 true *1 0.573,1.156 0.885,1.313 0.313,0.156 10 false *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly


Engage the 2 guides to connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door trim board sub-assembly.


b.
B488429

Engage the 6 claws and the guide.


c.

Engage the 7 clips and install the rear door trim board sub-assembly.


d.
B488428

Install the 3 screws.


e.
B347470

Engage the claw and close the door inside handle bezel plug.


Hide 74272A 29.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)

a.
B488427

Connect the connector.


b.
B488426

Engage the 8 claws, 2 clips and 4 guides to install the rear door armrest base upper panel.


Hide 74272A 30.INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)

a.
B483987

Engage the 3 claws, 2 clips and 2 guides to install the rear door armrest base upper panel.


Hide 74260 31.INSTALL REAR ARMREST ASSEMBLY (w/ Power Window)

a.
B488425

Engage the 7 claws, 3 clips and 3 guides to install the rear armrest assembly.


Hide 74260 32.INSTALL REAR ARMREST ASSEMBLY (w/o Power Window)

a.
B483986

Engage the 7 claws, 3 clips and 3 guides to install the rear armrest assembly.


Hide 69260E 33.INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

a.

Install the rear door window regulator handle assembly and fully open the rear door glass sub-assembly.


b.

Remove the rear door window regulator handle assembly.


c.
B346721C01
2.333,0.542 2.646,0.74 0.313,0.198 10 false *a 2.906,0.542 3.094,0.74 0.188,0.198 10 false *b
*a Door Panel Side
*b Inside of Vehicle


Install the window regulator handle plate as shown in the illustration.


d.
B483990C01
2.823,1.146 3.135,1.302 0.313,0.156 10 false *a 1.052,0.177 1.365,0.333 0.313,0.156 10 false *b 1.656,0.052 2.01,0.25 0.354,0.198 10 false 90° 0.594,0.594 0.948,0.792 0.354,0.198 10 false 30° 0.479,1.156 0.698,1.396 0.219,0.24 10 false 0°
*a Front of Vehicle
*b Assemble with Glass in Fully Open Position


Install the rear door window regulator handle assembly with the shaft snap ring at the angle shown in the illustration.


Hide 34.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (for Hatchback).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION