There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω. | ·
Short in CAN main bus line ·
Short in CAN branch line ·
Combination meter assembly ·
Airbag ECU assembly ·
Brake actuator assembly ·
ECM ·
Certification ECU (smart key ECU assembly)*1 ·
Air conditioning amplifier assembly ·
Spiral cable with sensor sub-assembly*2 ·
No. 1 CAN junction connector ·
Steering sensor*3, *4 ·
Power steering ECU assembly*3 ·
No. 23 CAN junction connector*3 |
*1: w/ Smart Entry and Start System
*2: for TMMIN Made
*3: for TMT Made
*4: w/ VSC
for TMMIN Made
for TMT Made
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.74 seconds or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for TMMIN Made | A |
| for TMT Made | B |
A
B
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-32 (CANH) - F38-31 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F38 combination meter assembly connector.
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F130-13 (CANH) - F130-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK (for 1NR-FE) | A |
| OK (for 2NR-FE) | B |
| NG | C |
A
B
C
Reconnect the F130 ECM connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | to DLC3 |
| *c | to Brake Actuator Assembly*1 |
| *d | to ECM |
| *e | to Airbag ECU Assembly*2 |
| *f | to Combination Meter Assembly |
| *g | to Certification ECU (Smart Key ECU Assembly)*3 |
| *h | to Air Conditioning Amplifier Assembly |
| *i | to Spiral Cable with Sensor Sub-assembly*4 |
Disconnect the No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F62-1 (CANH) - F62-12 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher | DLC3 |
| F62-2 (CANH) - F62-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly*1 |
| F62-3 (CANH) - F62-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| F62-4 (CANH) - F62-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag ECU assembly*2 |
| F62-6 (CANH) - F62-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| F62-7 (CANH) - F62-18 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Certification ECU (smart key ECU assembly)*3 |
| F62-8 (CANH) - F62-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| F62-9 (CANH) - F62-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Spiral cable with sensor sub-assembly*4 |
*1: w/ ABS
*2: w/ Airbag System
*3: w/ Smart Entry and Start System
*4: w/ VSC
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECM main line) | B |
| NG (ECU or sensor branch line) | C |
| NG (Combination meter assembly main line) | D |
| NG (DLC3 branch line) | E |
A
B
C
D
E
Reconnect the F62 No. 1 CAN junction connector.
Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F16-6 (CANH) - F16-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
| Result |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F38-23 (CANH) - F38-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F38 combination meter assembly connector.
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F130-13 (CANH) - F130-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F130 ECM connector.
| *a | Front view of wire harness connector
(to No. 23 CAN Junction Connector) |
| *b | to Brake Actuator Assembly |
| *c | to Combination Meter Assembly |
| *d | to No. 1 CAN Junction Connector |
Disconnect the No. 23 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A60-5 (CANH) - A60-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Brake actuator assembly |
| F174-5 (CANH) - F174-16 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| F174-6 (CANH) - F174-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 1 CAN junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 1 CAN junction connector main line) | B |
| NG (ECU or sensor branch line) | C |
| NG (Combination meter assembly main line) | D |
A
B
C
D
Reconnect the F174 and A60 No. 23 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 1 CAN Junction Connector) |
| *b | to DLC3 |
| *c | to No. 23 CAN Junction Connector |
| *d | to ECM |
| *e | to Airbag ECU Assembly |
| *f | to Certification ECU (Smart Key ECU Assembly)*1 |
| *g | to Air Conditioning Amplifier Assembly |
| *h | to Steering sensor*2 |
| *i | to Power Steering ECU Assembly |
Disconnect the No. 1 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| F62-1 (CANH) - F62-12 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher | DLC3 |
| F62-2 (CANH) - F62-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 23 CAN junction connector |
| F62-3 (CANH) - F62-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| F62-4 (CANH) - F62-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag ECU assembly |
| F62-7 (CANH) - F62-18 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Certification ECU (Smart key ECU assembly)*1 |
| F62-8 (CANH) - F62-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| F62-9 (CANH) - F62-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Steering sensor*2 |
| F62-10 (CANH) - F62-21 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Power steering ECU assembly |
*1: w/ Smart Entry and Start System
*2: w/ VSC
| Result | Proceed to |
|---|---|
| OK | A |
| NG (No. 23 CAN junction connector main line) | B |
| NG (ECU or sensor branch line) | C |
| NG (DLC3 branch line) | D |
| NG (ECM main line) | E |
A
B
C
D
E
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *1 | DLC3 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F16-6 (CANH) - F16-14 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
| Result |
|---|
| OK |
| NG |
OK
NG