Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0090060 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 2.DRAIN ENGINE COOLANT

Hide 55301 3.REMOVE INSTRUMENT PANEL SUB-ASSEMBLY (for TMMIN Made)

Hide 55303B 4.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for TMT Made)

Hide 6.REMOVE STEERING COLUMN ASSEMBLY (for TMMIN Made)

Hide 7.REMOVE STEERING COLUMN ASSEMBLY (for TMT Made)

Hide 88712 8.DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (w/ Cooler System)

a.
I109666

Remove the bolt.


b.

Turn the hook connector counterclockwise and disconnect the No. 1 cooler refrigerant suction hose.


c.

Remove the O-ring from the No. 1 cooler refrigerant suction hose.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88706A 9.DISCONNECT LIQUID TUBE SUB-ASSEMBLY A (w/ Cooler System)

a.

Disconnect the liquid tube sub-assembly A.


b.

Remove the O-ring from the liquid tube sub-assembly A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 88482 10.REMOVE COOLER CAP (w/o Cooler System)

a.
I109804

Remove the bolt and cooler cap.


b.

Remove the O-ring from the cooler cap.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



Hide 87246 11.DISCONNECT HEATER WATER OUTLET HOSE

I109970

a.

Loosen the hose clip and disconnect the heater water outlet hose from the heater radiator assembly.


Hide 87245 12.DISCONNECT HEATER WATER INLET HOSE

I109971

a.

Loosen the hose clip and disconnect the heater water inlet hose from the heater radiator assembly.


Hide 87211C 13.REMOVE NO. 4 AIR DUCT

a.
I113630C03
2.146,0.438 2.354,0.76 true 1.958,0.271 2.271,0.427 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the No. 4 air duct.


Hide 55306A 14.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Disengage the front floor carpet.


b.

Remove the clip and peel back the front floor carpet assembly.


c.
I109844

Disengage the 2 clamps.


d.

Remove the bolt, nut, screw and then remove the No. 1 instrument panel brace sub-assembly.


Hide 88539 15.SEPARATE NO. 1 COOLER UNIT DRAIN HOSE

a.
I109825

Separate the No. 1 cooler unit drain hose.


Hide 88539C 16.REMOVE NO. 2 COOLER UNIT DRAIN HOSE

a.
I109826

Remove the clip and No. 2 cooler unit drain hose.


Hide 88650N 17.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)

Hide 88650N 18.REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)

Hide 87165C 19.REMOVE BLOWER MOTOR CONTROL (for Automatic Air Conditioning System)

Hide 87138C 20.REMOVE BLOWER RESISTOR (for Manual Air Conditioning System)

Hide 87010 21.REMOVE AIR CONDITIONING UNIT ASSEMBLY

a.

for LHD:

i.
I109827

Disengage the clamp.


ii.

Disconnect the connector.



b.

for RHD:

i.
I109675

Disengage the 2 clamps.


ii.

Disconnect the connector.



c.
I109828

Remove the 2 screws.


d.
I109829

Remove the nut and bolt.


e.

for Automatic Air Conditioning System:

i.

Pull the air conditioning unit assembly toward the rear of the vehicle.


ii.
I109720

Disconnect the connector and remove the air conditioning unit assembly.



f.

for Manual Air Conditioning System:

i.

Pull the air conditioning unit assembly toward the rear of the vehicle.


ii.
I109671

Disconnect the connector and remove the air conditioning unit assembly.



Hide 87211G 22.REMOVE NO. 5 AIR DUCT

I109832C01
0.948,0.823 1.26,0.417 true 1.292,0.292 1.51,0.49 0.219,0.198 10 true *a
*a Protective Tape


a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 3 claws and remove the No. 5 air duct.