44610
1.INSTALL BRAKE BOOSTER ASSEMBLY
Install a new brake booster gasket to the brake booster assembly.
Temporarily install the brake booster assembly to the body with the 4 nuts.
Tighten the 4 nuts in the order shown in the illustration.
Connect the vacuum sensor assembly connector.
47264D
2.INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
Install the clevis lock nut and brake master cylinder push rod clevis to the brake booster assembly.
Tighten the clevis lock nut after adjusting the brake pedal height.
|
Lithium Soap Base Glycol Grease |
Apply lithium soap base glycol grease to the push rod pin.
Install the brake master cylinder push rod clevis to the brake pedal sub-assembly with the push rod pin and a new clip.
Install the push rod pin from the right side of the vehicle.
47101A
3.INSTALL BRAKE PEDAL RETURN SPRING
4.INSTALL WIRE HARNESS
84340
5.INSTALL STOP LIGHT SWITCH ASSEMBLY
44772
6.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE (for CVT)
Connect the 2 check valve to connector tube hoses to the 2 brake vacuum check valve assemblies with the 2 hose clips.
44772
7.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE (for Manual Transaxle)
Connect the check valve to connector tube hose to the brake vacuum check valve assembly with the hose clip.
47315
8.INSTALL FRONT NO. 5 BRAKE TUBE
| *a | Torque Wrench Fulcrum Length |
Install the front No. 5 brake tube and grommet to the body.
Using a 10 mm union nut wrench, connect the front No. 5 brake tube to the front flexible hose while holding the front flexible hose with the wrench.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
44510
9.INSTALL BRAKE ACTUATOR ASSEMBLY
for Manual Transaxle:
Install the brake actuator assembly with the brake actuator bracket assembly with the 3 bolts in the sequence shown in the illustration.
Do not damage the brake tubes or wire harness.
Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.
| *a | Lock Lever |
Connect the brake actuator connector.
Make sure that the connector is locked securely.
Make sure that the brake actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.
for CVT:
Install the brake actuator assembly with the brake actuator bracket assembly with the 3 bolts in the sequence shown in the illustration.
Do not damage the brake tubes or wire harness.
Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.
| *a | Lock Lever |
Connect the brake actuator connector.
Make sure that the connector is locked securely.
Make sure that the brake actuator connector can be connected smoothly. Do not allow entry of water, oil or dirt.
45209
10.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY
45259A
11.INSTALL COLUMN HOLE COVER SILENCER SHEET
55432B
12.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL
55606
13.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
73900
14.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
47201
15.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
w/ ABS:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for LHD)>INSTALLATION
w/ VSC:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER(for LHD)>INSTALLATION
16.INSPECT AND ADJUST BRAKE PEDAL