Home › Drivetrain › K411 CVT › TRANSMISSION CONTROL CABLE › from 2018.01
RM30M0E _52 Drivetrain _052750 K411 CVT _0259923 TRANSMISSION CONTROL CABLE A

K411 CVT  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

To prevent damage to the transmission control cable assembly and transmission floor shift assembly, connect the continuously variable transaxle assembly side of the transmission control cable assembly before connecting the transmission floor shift assembly side.


a.

Install the transmission control cable assembly to the body with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
C288559C01
2.885,0.875 3.083,1.063 0.198,0.188 10 true *a 2.646,0.396 2.823,0.573 0.177,0.177 10 true *b
*a P Position
*b N Position


Rotate the transmission control shaft lever clockwise until it stops, and then from that position rotate it counterclockwise by 2 notches to set it to the N position.


c.
C288554C01
0.948,0.458 1.458,0.458 true 0.781,0.354 0.938,0.552 0.156,0.198 10 true *a
*a Paint Mark


Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

NOTICE:

Make sure that the paint mark on the transmission control cable assembly is aligned with the slit in the No. 1 transmission control cable bracket before installing the clip.



d.

Connect the transmission control cable assembly to the transmission control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


e.
C288539C01
2.24,0.906 2.552,0.708 false 1,1.875 1.313,1.677 false 0.854,1.781 1.167,1.938 0.313,0.156 10 false *1 2.594,0.604 2.906,0.76 0.313,0.156 10 false *2
*1 Nut
*2 Lock
V100135

Rotate approximately 180°
V100136

Push in


Rotate the nut of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut, push in the lock.

NOTICE:

Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.



f.
C381195C06
0.667,2.333 0.917,2.583 false 2.417,2.333 2.75,2.583 false 2.24,2.229 2.417,2.417 0.177,0.188 10 true *1 0.5,2.229 0.667,2.438 0.167,0.208 10 true *a 1.375,2.531 1.5,2.729 0.125,0.198 10 true A 0.375,2.531 0.521,2.729 0.146,0.198 10 true A
*1 Lock
*a Protrusion
V100135

Push in


Install the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Install the transmission control cable assembly with the protrusion facing upwards.

·

After installation, make sure that the lock is projecting from A as shown in the illustration.

·

Make sure that the transmission control cable assembly is securely locked.




g.
C381196

Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Securely install the end of the transmission control cable assembly to the transmission floor shift assembly.

·

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.




Hide 2.ADJUST SHIFT LEVER POSITION

Hide 58151 3.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the body with the 2 bolts and nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 4.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 5.INSTALL FRONT FLOOR CENTER BRACE

Hide 58810J 6.INSTALL CONSOLE BOX ASSEMBLY

Hide 58839A 7.INSTALL CONSOLE BOX HOLE COVER

Hide 58912C 9.INSTALL NO. 2 BOX SIDE PANEL

Hide 58911A 10.INSTALL NO. 1 BOX SIDE PANEL

Hide 58817A 11.INSTALL NO. 2 FRONT CONSOLE BOX INSERT

Hide 58910C 13.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 17701 17.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 18.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17880 20.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 21.INSPECT FOR EXHAUST GAS LEAK

HINT:

Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


Hide 22.INSPECT SHIFT LEVER POSITION