Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › from 2018.01
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B342588E01
2.365,0.563 3.396,0.844 1.031,0.281 10 false from Battery 1.917,1.01 3.396,1.354 1.479,0.344 10 false from D/C CUT Fuse 2,1.458 3.479,1.802 1.479,0.344 10 false to IG Relay Circuit 1.854,1.885 3.333,2.229 1.479,0.344 10 false to ACC Relay Circuit 3.958,0.719 5.438,1.063 1.479,0.344 10 false AM2 NO. 2 4.115,1.156 4.656,1.469 0.542,0.313 10 false DOME 1.927,2.531 2.958,2.813 1.031,0.281 10 false 4 1.927,2.969 2.271,3.25 0.344,0.281 10 false 5 1.917,3.406 2.26,3.688 0.344,0.281 10 false 2 1.906,3.833 2.25,4.115 0.344,0.281 10 false 1 1.677,2.615 2.01,2.906 0.333,0.292 10 false +5 1.5,3.052 1.99,3.344 0.49,0.292 10 false DATA 1.51,3.479 2,3.771 0.49,0.292 10 false CSEL 1.573,3.917 2.063,4.208 0.49,0.292 10 false GND 0.719,4.458 2.104,5.052 1.385,0.594 10 false Door Control Receiver 0.719,4.292 1.208,4.583 0.49,0.292 10 false F46 5.417,0.583 5.802,0.771 0.385,0.188 10 false F43 5.406,1.458 5.792,1.646 0.385,0.188 10 false F43 5.406,1.896 5.792,2.083 0.385,0.188 10 false F43 5.406,3.917 5.792,4.104 0.385,0.188 10 false F43 5.406,1.021 5.792,1.208 0.385,0.188 10 false F44 5.406,2.615 5.792,2.802 0.385,0.188 10 false F44 5.417,3.052 5.802,3.24 0.385,0.188 10 false F44 5.479,0.396 5.698,0.594 0.219,0.198 10 false 1 5.458,0.844 5.844,1.031 0.385,0.188 10 false 33 5.458,1.271 5.844,1.458 0.385,0.188 10 false 20 5.458,1.708 5.844,1.896 0.385,0.188 10 false 21 5.49,2.427 5.875,2.615 0.385,0.188 10 false 3 5.438,2.865 5.823,3.052 0.385,0.188 10 false 22 5.458,3.302 5.844,3.49 0.385,0.188 10 false 21 5.458,3.729 5.844,3.917 0.385,0.188 10 false 10 5.417,4.656 6.958,5.25 1.542,0.594 10 false Certification ECU (Smart Key ECU Assembly) 5.708,0.583 6.198,0.875 0.49,0.292 10 false +B 5.719,1.031 6.208,1.323 0.49,0.292 10 false CUTB 5.719,1.448 6.208,1.74 0.49,0.292 10 false IG1D 5.729,1.896 6.219,2.188 0.49,0.292 10 false ACCD 5.729,2.615 6.219,2.906 0.49,0.292 10 false RCO 5.729,3.052 6.219,3.344 0.49,0.292 10 false RDAS 5.719,3.49 6.208,3.781 0.49,0.292 10 false CSEL 5.729,3.906 6.219,4.198 0.49,0.292 10 false E 5.417,3.49 5.802,3.677 0.385,0.188 10 false F44

E377894E07
5.594,1.479 6.208,1.677 0.615,0.198 10 false F44 5.594,2.021 6.208,2.219 0.615,0.198 10 false F44 5.979,1.458 6.594,1.656 0.615,0.198 10 false PRG3 5.979,2.021 6.594,2.219 0.615,0.198 10 false RDA3 5.625,3.333 7.156,3.906 1.531,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.625,1.271 6.156,1.458 0.531,0.188 10 false 36 5.625,1.823 6.156,2.01 0.531,0.188 10 false 13 4.854,1.479 5.469,1.677 0.615,0.198 10 false F52 4.865,2.021 5.479,2.219 0.615,0.198 10 false F52 4.917,1.292 5.531,1.49 0.615,0.198 10 false 9 4.885,1.833 5.5,2.031 0.615,0.198 10 false 16 4.448,1.479 5.063,1.677 0.615,0.198 10 false PRG 4.458,2 5.073,2.198 0.615,0.198 10 false RDA 3.573,3.188 4.188,3.385 0.615,0.198 10 false F52 3.594,0.698 4.208,0.896 0.615,0.198 10 false MB 3.906,0.688 4.521,0.885 0.615,0.198 10 false DCTY 3.927,3.188 4.542,3.385 0.615,0.198 10 false PCTY 3.865,3.552 5.01,3.958 1.146,0.406 10 false Body Computer 2.698,0.698 3.313,0.896 0.615,0.198 10 false 6M 2.688,2.115 3.302,2.313 0.615,0.198 10 false 6M 2.74,0.531 3.354,0.729 0.615,0.198 10 false 2 3.615,3 4.229,3.198 0.615,0.198 10 false 14 2.75,1.927 3.365,2.125 0.615,0.198 10 false 4 2.281,2.583 3.521,3.042 1.24,0.458 10 false Driver Side Junction Block Assembly 3.604,0.521 4.219,0.719 0.615,0.198 10 false 18 2.177,0.594 2.792,0.792 0.615,0.198 10 false 1 1.094,0.958 1.708,1.156 0.615,0.198 10 false F31 1.083,1.125 2.688,1.646 1.604,0.521 10 false Front Door Courtesy Light Switch Assembly LH 2.063,4.125 2.677,4.323 0.615,0.198 10 false 1 2.063,5.24 2.677,5.438 0.615,0.198 10 false 1 2.031,6.417 2.646,6.615 0.615,0.198 10 false 1 0.198,7.021 0.813,7.219 0.615,0.198 10 false F38 0.188,7.208 1.365,7.635 1.177,0.427 10 false Combination Meter Assembly 0.813,2.125 1.427,2.323 0.615,0.198 10 false DCTY 0.802,4.229 1.417,4.427 0.615,0.198 10 false PCTY 0.813,3.198 1.427,3.396 0.615,0.198 10 false ACTY 0.813,5.354 1.427,5.552 0.615,0.198 10 false RLCY 0.792,6.552 1.406,6.75 0.615,0.198 10 false RRCY 1.292,2.01 1.906,2.208 0.615,0.198 10 false 30 1.292,3.052 1.906,3.25 0.615,0.198 10 false 29 1.292,4.104 1.906,4.302 0.615,0.198 10 false 31 1.281,5.26 1.896,5.458 0.615,0.198 10 false 32 1.302,6.427 1.917,6.625 0.615,0.198 10 false 33 1.75,4.448 2.365,4.646 0.615,0.198 10 false F32 1.75,4.604 3.354,5.125 1.604,0.521 10 false Front Door Courtesy Light Switch Assembly RH 1.813,5.583 2.427,5.781 0.615,0.198 10 false F33 1.813,5.76 3.417,6.281 1.604,0.521 10 false Rear Door Courtesy Light Switch Assembly LH 1.813,6.781 2.427,6.979 0.615,0.198 10 false F34 1.802,6.979 3.406,7.5 1.604,0.521 10 false Rear Door Courtesy Light Switch Assembly RH 0.167,0.167 0.833,0.417 0.667,0.25 12 false for LHD:

E377894E06
5.594,1.479 6.208,1.677 0.615,0.198 10 false F44 5.594,2.021 6.208,2.219 0.615,0.198 10 false F44 5.979,1.458 6.594,1.656 0.615,0.198 10 false PRG3 5.979,2.021 6.594,2.219 0.615,0.198 10 false RDA3 5.625,3.333 7.156,3.906 1.531,0.573 10 false Certification ECU (Smart Key ECU Assembly) 5.625,1.271 6.156,1.458 0.531,0.188 10 false 36 5.625,1.823 6.156,2.01 0.531,0.188 10 false 13 4.854,1.479 5.469,1.677 0.615,0.198 10 false F52 4.865,2.021 5.479,2.219 0.615,0.198 10 false F52 4.917,1.292 5.531,1.49 0.615,0.198 10 false 9 4.885,1.833 5.5,2.031 0.615,0.198 10 false 16 4.448,1.479 5.063,1.677 0.615,0.198 10 false PRG 4.458,2 5.073,2.198 0.615,0.198 10 false RDA 3.573,3.188 4.188,3.385 0.615,0.198 10 false F52 3.594,0.698 4.208,0.896 0.615,0.198 10 false MB 3.906,0.688 4.521,0.885 0.615,0.198 10 false DCTY 3.927,3.188 4.542,3.385 0.615,0.198 10 false PCTY 3.865,3.552 5.01,3.958 1.146,0.406 10 false Body Computer 2.698,0.698 3.313,0.896 0.615,0.198 10 false 6M 2.688,2.115 3.302,2.313 0.615,0.198 10 false 6M 2.74,0.531 3.354,0.729 0.615,0.198 10 false 2 3.615,3 4.229,3.198 0.615,0.198 10 false 14 2.75,1.927 3.365,2.125 0.615,0.198 10 false 4 2.281,2.583 3.521,3.042 1.24,0.458 10 false Driver Side Junction Block Assembly 3.604,0.521 4.219,0.719 0.615,0.198 10 false 18 2.177,0.594 2.792,0.792 0.615,0.198 10 false 1 1.094,0.958 1.708,1.156 0.615,0.198 10 false F32 1.083,1.125 2.688,1.646 1.604,0.521 10 false Front Door Courtesy Light Switch Assembly RH 2.063,4.125 2.677,4.323 0.615,0.198 10 false 1 2.063,5.24 2.677,5.438 0.615,0.198 10 false 1 2.031,6.417 2.646,6.615 0.615,0.198 10 false 1 0.198,7.021 0.813,7.219 0.615,0.198 10 false F38 0.188,7.208 1.365,7.635 1.177,0.427 10 false Combination Meter Assembly 0.813,2.125 1.427,2.323 0.615,0.198 10 false DCTY 0.802,4.229 1.417,4.427 0.615,0.198 10 false PCTY 0.813,3.198 1.427,3.396 0.615,0.198 10 false ACTY 0.813,5.354 1.427,5.552 0.615,0.198 10 false RLCY 0.792,6.552 1.406,6.75 0.615,0.198 10 false RRCY 1.292,2.01 1.906,2.208 0.615,0.198 10 false 30 1.292,3.052 1.906,3.25 0.615,0.198 10 false 29 1.292,4.104 1.906,4.302 0.615,0.198 10 false 31 1.281,5.26 1.896,5.458 0.615,0.198 10 false 32 1.302,6.427 1.917,6.625 0.615,0.198 10 false 33 1.75,4.448 2.365,4.646 0.615,0.198 10 false F31 1.75,4.604 3.354,5.125 1.604,0.521 10 false Front Door Courtesy Light Switch Assembly LH 1.813,5.583 2.427,5.781 0.615,0.198 10 false F33 1.813,5.76 3.417,6.281 1.604,0.521 10 false Rear Door Courtesy Light Switch Assembly LH 1.813,6.781 2.427,6.979 0.615,0.198 10 false F34 1.802,6.979 3.406,7.5 1.604,0.521 10 false Rear Door Courtesy Light Switch Assembly RH 0.167,0.167 0.833,0.417 0.667,0.25 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) or DTC B27B0 is not output.

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".



PROCEDURE

1.INSPECT BATTERY VOLTAGE
a.

Measure the voltage of the vehicle battery.

Standard voltage:

11 to 14 V


HINT:

It may be possible to tell whether the vehicle battery is discharged by operating the horn.

If the voltage is below 11 V, recharge or replace the vehicle battery before proceeding.



Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Connect the GTS and check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:

When using the GTS with the engine switch off to troubleshoot: Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.


OK:

DTC is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK DOOR AJAR WARNING OPERATION

NG

3.CHECK DOOR AJAR WARNING OPERATION
a.

When door unlock by entry lock or wireless door lock operation functions even though all doors are closed, check the door ajar warning operation.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>SYSTEM DESCRIPTION

OK:

Door ajar warning does not operate.



Result:
Proceed to
OK
NG



OK

4.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

43.CHECK LIGHTING SYSTEM (INT) OPERATION
4.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the power window regulator master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

5.CHECK KEY DIAGNOSTIC MODE

NG

5.CHECK KEY DIAGNOSTIC MODE

b.

Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.

HINT:

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



c.

for Sedan

i.
B354279C09
0.125,0.271 0.438,0.5 0.313,0.229 12 false *A 0.135,2.74 0.448,2.958 0.313,0.219 12 false *B 2.083,1.542 2.396,1.698 0.313,0.156 10 false *a 1.542,3.719 1.854,3.875 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna:

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

ii.
B342599C02
2.365,1.01 2.531,1.01 false 0.667,1.135 2.646,0.521 2.646,0.521 1.771,1.135 true 2.688,0.406 3,0.604 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (instrument panel):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iii.
B342600C18
1.781,0.292 2.313,0.094 2.313,0.094 0.646,0.302 true 2.365,0 2.677,0.156 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iv.
B342601C13
1.813,1.219 2.125,1.417 0.313,0.198 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (outside luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143


d.

for Hatchback

i.
B354279C10
0.125,0.271 0.438,0.5 0.313,0.229 12 false *A 0.135,2.74 0.448,2.958 0.313,0.219 12 false *B 2.083,1.542 2.396,1.698 0.313,0.156 10 false *a 1.542,3.719 1.854,3.875 0.313,0.156 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna:

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

ii.
B342599C02
2.365,1.01 2.531,1.01 false 0.667,1.135 2.646,0.521 2.646,0.521 1.771,1.135 true 2.688,0.406 3,0.604 0.313,0.198 10 false *a
*a Inspection Point


Check the No. 1 indoor electrical key antenna assembly (instrument panel):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iii.
B345012C09
0.74,0.573 2.646,0.146 2.646,0.146 1.865,0.573 true 2.729,0.063 3.042,0.219 0.313,0.156 10 false *a
*a Inspection Point


Check the No. 2 indoor electrical key antenna assembly (rear floor):

When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

iv.
B345011C10
1.802,1.281 2.115,1.438 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


Check the electrical key antenna (outside luggage compartment):

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless door lock buzzer sounds.

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143


OK:

Wireless door lock buzzer sounds.


Result:
Result Proceed to
Diagnostic mode inspections fail for both channels A
Diagnostic mode inspections succeed for both channels B
Diagnostic mode inspection succeeds for only one of the channels C



A

6.CHECK WAVE ENVIRONMENT

B

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

C

33.CHECK WAVE ENVIRONMENT
6.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



Result:
Result Proceed to
Wireless and entry functions does not operate A
Wireless and entry functions operate normally B




A

7.CHECK TRANSMITTER BATTERY

B

AFFECTED BY WAVE INTERFERENCE

7.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST

·

Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly against the engine switch, depressing the brake pedal*1 or clutch pedal*2 and pressing the engine switch.


*1: for CVT

*2: for Manual Transaxle





Result:
Result Proceed to
Transmitter LED illuminates 3 times or more when switch is pressed and held A
Transmitter LED does not illuminate when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C



A

8.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

17.INSPECT TRANSMITTER BATTERY (VOLTAGE)

C

8.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.


Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assemblies B



A

9.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

10.CHECK ENTRY DOOR LOCK OPERATION
9.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK ENTRY DOOR LOCK OPERATION
10.CHECK ENTRY DOOR LOCK OPERATION
a.

Using another registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

OK:

Entry lock/unlock operate normally.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

NG

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)- DOOR CONTROL RECEIVER)
11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)- DOOR CONTROL RECEIVER)
a.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the F46 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F44-3 (RCO) - F46-4 (+5) Always Below 1 Ω
F44-22 (RDAS) - F46-5 (DATA) Always Below 1 Ω
F44-21 (CSEL) - F46-2 (CSEL) Always Below 1 Ω
F43-10 (E) - Body ground Always Below 1 Ω
F44-3 (RCO) or F46-4 (+5) - Body ground Always 10 kΩ or higher
F44-22 (RDAS) or F46-5 (DATA) - Body ground Always 10 kΩ or higher
F44-21 (CSEL) or F46-2 (CSEL) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

12.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK ENTRY DOOR LOCK OPERATION
a.

Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Connect the F46 door control receiver connector.



Result:
Result Proceed to
Entry lock/unlock does not operate A
Entry lock/unlock operate normally B



A

13.CHECK DOOR CONTROL RECEIVER

B

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

13.CHECK DOOR CONTROL RECEIVER
a.

Measure the resistance according to the value(s) in the table below.

B327899C49
1.594,0.333 2.042,0.563 0.448,0.229 1.156,2.063 1.51,1.281 true 2.51,2.073 2.156,1.281 true 1.688,0.375 2.146,0.573 0.458,0.198 10 false F46 3.719,1.219 4.177,1.417 0.458,0.198 10 false GND 4.385,1.948 4.844,2.146 0.458,0.198 10 false *c 3.948,0.396 4.406,0.594 0.458,0.198 10 false *b 0.333,0.24 0.792,0.438 0.458,0.198 10 false *a 0.99,2.104 1.448,2.302 0.458,0.198 10 false DATA 5.396,1.958 5.854,2.156 0.458,0.198 10 false *d 2.385,2.104 2.844,2.302 0.458,0.198 10 false GND
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock button of electrical key transmitter sub-assembly pressed *d After lock or unlock button of electrical key transmitter sub-assembly pressed


Standard Resistance:
Tester Connection Condition Specified Condition
F46-1 (GND) - Body ground Always Below 1 Ω



b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
F46-5 (DATA) - F46-1 (GND)
Procedure:
1.

Engine switch off

2.

All doors locked

3.

Lock or unlock button of electrical key transmitter subassembly not pressed → pressed


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)


Result:
Result Proceed to
OK A
NG (for Sedan) B
NG (for Hatchback) C




A

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

14.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Connect the F46 door control receiver connector.


c.

Measure the voltage according to the value(s) in the table below.

B348668C28
1.583,0.417 2.083,0.667 0.5,0.25 2.948,2.177 2.167,1.25 true 2.25,2.188 2,1.271 true 1.344,2.188 1.677,1.271 true 0.76,0.5 1.073,0.698 0.313,0.198 10 false *a 3.854,0.583 4.167,0.781 0.313,0.198 10 false *b 2.823,2.219 3.135,2.417 0.313,0.198 10 false GND 1.26,2.219 1.573,2.417 0.313,0.198 10 false +5 2.073,2.219 2.552,2.417 0.479,0.198 10 false CSEL 3.667,1.333 3.979,1.531 0.313,0.198 10 false GND 1.688,0.469 2.177,0.76 0.49,0.292 10 false F46
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1


Standard Voltage:
Tester Connection Condition Specified Condition
F46-4 (+5) - F46-1 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch pressed


Below 1 V → 4.5 to 5.5 V



d.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
F46-2 (CSEL) - F46-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

16.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
16.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

17.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery

i.

Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT


ii.
B327509C04
2.76,0.906 3.073,0.448 false 3.104,0.313 3.323,0.521 0.219,0.208 10 false *a
*a Lead Wire


Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



iii.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iv.
B327510C02
2.365,1.115 1.688,0.375 false 1.49,0.281 1.802,0.479 0.313,0.198 10 false *a
*a GND


Measure the voltage of the transmitter battery.

HINT:
·

When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the trigger switch of a door handle to perform the measurement.

·

Perform the measurement when the key is at room temperature.

·

The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DATA LIST / ACTIVE TEST



Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Engine switch off, all doors closed and trigger switch pressed 2.3 to 3.2 V




Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

18.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state All OFF, ACC ON, IG ON or ST ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG ON: Engine switch on (IG)
ST ON: Sending engine start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18

f.

Measure the voltage according to the value(s) in the table below.

E374147C29
2.417,0.417 2.917,0.667 0.5,0.25 3.125,2.385 2.5,1.49 true 1.99,2.354 2.448,1.49 true 0.188,0.302 0.5,0.5 0.313,0.198 10 false *a 2.531,0.458 3.135,0.771 0.604,0.313 10 false F43 3.042,2.417 3.458,2.635 0.417,0.219 10 false IG1D 1.802,2.396 2.219,2.615 0.417,0.219 10 false ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F43-20 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher
F43-21 (ACCD) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 8.5 V or higher
Engine switch on (IG) 8.5 V or less



Result:
Proceed to
OK
NG



OK

19.INSPECT NO. 1 IGNITION RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

19.INSPECT NO. 1 IGNITION RELAY
a.

Remove the No. 1 ignition relay.


b.
B344996E01
1.969,0.906 2.302,1.083 true 2.427,0.24 2.604,0.604 true 2.917,1.094 3.229,0.917 true 2.615,1.635 2.823,1.917 true 3.26,0.823 3.417,1.021 0.156,0.198 10 false 1 2.302,0.135 2.458,0.333 0.156,0.198 10 false 3 1.844,0.823 2,1.021 0.156,0.198 10 false 2 2.813,1.958 2.969,2.156 0.156,0.198 10 false 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (NO. 1 IGNITION RELAY))

NG

REPLACE NO. 1 IGNITION RELAY

20.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (NO. 1 IGNITION RELAY))
a.

Remove the No. 1 ignition relay from No. 4 relay block.


b.

Measure the voltage according to the value(s) in the table below.

E377752C01
0.375,0.26 0.75,0.5 0.375,0.24 12 false *A 3.833,0.26 4.208,0.5 0.375,0.24 12 false *B 1.573,0.354 1.948,0.594 0.375,0.24 10 false *2 4.333,0.833 4.708,1.073 0.375,0.24 10 false *1 4.938,0.375 5.313,0.615 0.375,0.24 10 false *2 0.698,0.531 1.073,0.771 0.375,0.24 10 false *1
*A for LHD *B for RHD
*1 No. 4 Relay Block *2 No. 1 Ignition Relay Holder


Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 ignition relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (NO. 1 IGNITION RELAY - BODY GROUND)
a.

Remove the No. 1 ignition relay from No. 4 relay block.


b.

Measure the resistance according to the value(s) in the table below.

E377752C01
0.375,0.26 0.75,0.5 0.375,0.24 12 false *A 3.833,0.26 4.208,0.5 0.375,0.24 12 false *B 1.573,0.354 1.948,0.594 0.375,0.24 10 false *2 4.333,0.833 4.708,1.073 0.375,0.24 10 false *1 4.938,0.375 5.313,0.615 0.375,0.24 10 false *2 0.698,0.531 1.073,0.771 0.375,0.24 10 false *1
*A for LHD *B for RHD
*1 No. 4 Relay Block *2 No. 1 Ignition Relay Holder


Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 ignition relay terminal 2 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (NO. 1 IGNITION RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (NO. 1 IGNITION RELAY))
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Remove the No. 1 ignition relay from No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-20 (IG1D) - No. 1 ignition relay terminal 1 Always Below 1 Ω
F43-20 (IG1D) or No. 1 ignition relay terminal 1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT NO. 2 IGNITION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT NO. 2 IGNITION RELAY
a.

Remove the No. 2 ignition relay.


b.
A232574E13
2.313,0.76 1.938,0.479 true 2.896,0.677 3.208,0.469 true 2.792,1.115 3.188,1.115 true 2.802,1.594 3.177,1.594 true 1.823,0.385 1.927,0.542 0.104,0.156 10 1 3.271,0.385 3.375,0.542 0.104,0.156 10 2 3.229,1.531 3.333,1.688 0.104,0.156 10 3 3.24,1.042 3.344,1.198 0.104,0.156 10 5

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage applied to terminals 1 and 2 Below 1 Ω



Result:
Proceed to
OK
NG



OK

24.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (NO. 2 IGNITION RELAY))

NG

REPLACE NO. 2 IGNITION RELAY

24.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 4 RELAY BLOCK (NO. 2 IGNITION RELAY))
a.

Remove the No. 2 ignition relay from No. 4 relay block.


b.

Measure the voltage according to the value(s) in the table below.

E377753C01
0.24,0.229 0.615,0.469 0.375,0.24 12 false *A 4,0.281 4.375,0.521 0.375,0.24 12 false *B 4.219,0.854 4.594,1.094 0.375,0.24 10 false *1 0.604,0.51 0.979,0.75 0.375,0.24 10 false *1 1.563,0.344 1.938,0.583 0.375,0.24 10 false *2 4.802,0.417 5.177,0.656 0.375,0.24 10 false *2
*A for LHD *B for RHD
*1 No. 4 Relay Block *2 No. 2 Ignition Relay Holder


Standard Voltage:
Tester Connection Condition Specified Condition
No. 2 ignition relay terminal 3 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (NO. 2 IGNITION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (NO. 2 IGNITION RELAY - BODY GROUND)
a.

Remove the No. 2 ignition relay from No. 4 relay block.


b.

Measure the resistance according to the value(s) in the table below.

E377753C01
0.24,0.229 0.615,0.469 0.375,0.24 12 false *A 4,0.281 4.375,0.521 0.375,0.24 12 false *B 4.219,0.854 4.594,1.094 0.375,0.24 10 false *1 0.604,0.51 0.979,0.75 0.375,0.24 10 false *1 1.563,0.344 1.938,0.583 0.375,0.24 10 false *2 4.802,0.417 5.177,0.656 0.375,0.24 10 false *2
*A for LHD *B for RHD
*1 No. 4 Relay Block *2 No. 2 Ignition Relay Holder


Standard Resistance:
Tester Connection Condition Specified Condition
No. 2 ignition relay terminal 1 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (NO. 2 IGNITION RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 4 RELAY BLOCK (NO. 2 IGNITION RELAY))
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Remove the No. 2 ignition relay from No. 4 relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-20 (IG1D) - No. 2 ignition relay terminal 2 Always Below 1 Ω
F43-20 (IG1D) or No. 2 ignition relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

27.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the body computer from the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B342624C25
1.031,0.333 1.417,0.583 0.385,0.25 2.615,0.333 3,0.583 0.385,0.25 4.167,0.333 4.552,0.583 0.385,0.25 5.75,0.333 6.135,0.583 0.385,0.25 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 1.135,0.365 1.448,0.563 0.313,0.198 10 false 6A 2.729,0.365 3.042,0.563 0.313,0.198 10 false 6L 4.281,0.365 4.594,0.563 0.313,0.198 10 false 6F 5.865,0.365 6.177,0.563 0.313,0.198 10 false 6J
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
6A-1 - 6L-5 Battery voltage not applied to terminals 6F-2 and 6J-8 10 kΩ or higher
Battery voltage applied to terminals 6F-2 and 6J-8 Below 1 Ω



Result:
Proceed to
OK
NG



OK

28.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

28.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 6F and 6J driver side block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-21 (ACCD) - 6F-2 Always Below 1 Ω
6J-8 - Body ground Always Below 1 Ω
F43-21 (ACCD) or 6F-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - BATTERY AND BODY GROUND)
a.

Disconnect the certification ECU (smart key ECU assembly) connectors.


B342591C03
4.854,0.406 5.323,0.677 0.469,0.271 1.438,0.406 1.896,0.677 0.458,0.271 2.656,1.396 2.885,2.167 true 0.396,2.146 0.646,1.396 true 5.542,1.531 5.813,2.208 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 0.271,2.198 0.583,2.396 0.313,0.198 10 false +B 2.854,2.219 3.167,2.417 0.313,0.198 10 false E 5.698,2.281 6.281,2.469 0.583,0.188 10 false CUTB 4.979,0.458 5.438,0.656 0.458,0.198 10 false F44 1.552,0.458 2.031,0.656 0.479,0.198 10 false F43
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-10 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F44-33 (CUTB) - Body ground Always 11 to 14 V
F43-1 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

30.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK ENTRY DOOR LOCK OPERATION
a.

Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.



Result:
Result Proceed to
Entry lock/unlock does not operate A
Entry lock/unlock operate normally B



A

31.REPLACE REPLACE SMART KEY ECU ASSEMBLY (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

31.REPLACE REPLACE SMART KEY ECU ASSEMBLY (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

32.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
32.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

33.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly that was checked first near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless door lock buzzer sounds.



Result:
Result Proceed to
Wireless door lock buzzer does not sound A
Wireless door lock buzzer sounds B



A

34.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

AFFECTED BY WAVE INTERFERENCE

34.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.


Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assemblies B



A

35.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

36.CHECK KEY DIAGNOSTIC MODE
35.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

36.CHECK KEY DIAGNOSTIC MODE
36.CHECK KEY DIAGNOSTIC MODE
a.

Bring another registered electrical key transmitter sub-assembly near the door control receiver and select the failed channel (the channel in which the buzzer did not sound) to recheck the key diagnostic mode.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless door lock buzzer sounds.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY WAS DEFECTIVE)

NG

37.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
37.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - DOOR CONTROL RECEIVER)
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F46 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-21 (CSEL) - F46-2 (CSEL) Always Below 1 Ω
F44-21 (CSEL) or F46-2 (CSEL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

38.CHECK ENTRY DOOR LOCK OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

38.CHECK ENTRY DOOR LOCK OPERATION
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Connect the F46 door control receiver connector.



Result:
Result Proceed to
Entry lock/unlock does not operate A
Entry lock/unlock operate normally B



A

39.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

END (CONNECTOR WAS NOT CONNECTED PROPERLY)

39.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Connect the F46 door control receiver connector.


c.

Using an oscilloscope, check the waveform.

B348668C29
1.625,0.469 2.052,0.698 0.427,0.229 2.615,2.177 2.167,1.25 true 1.906,2.177 2,1.271 true 0.76,0.5 1.073,0.698 0.313,0.198 10 false *a 3.854,0.583 4.167,0.781 0.313,0.198 10 false *b 2.49,2.219 2.802,2.417 0.313,0.198 10 false GND 1.719,2.219 2.198,2.417 0.479,0.198 10 false CSEL 3.667,1.333 3.979,1.531 0.313,0.198 10 false GND 1.698,0.5 2.188,0.771 0.49,0.271 10 false F44
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1


OK:
Tester Connection Condition Tool Setting Specified Condition
F46-2 (CSEL) - F46-1 (GND) Procedure:
1.

Engine switch off

2.

All doors closed


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

40.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

40.CHECK DOOR CONTROL RECEIVER
a.

Using an oscilloscope, check the waveform.

HINT:

Inspection should be performed while the electrical key antenna check in key diagnostic mode is being performed on the failed channel (the channel in which the buzzer did not sound).


B327899C50
1.594,0.521 2.115,0.74 0.521,0.219 1.177,2.083 1.479,1.26 true 2.604,2.073 2.188,1.281 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 1.708,0.552 2.167,0.802 0.458,0.25 10 false F46 0.99,2.104 1.49,2.323 0.5,0.219 10 false DATA 2.458,2.104 2.958,2.323 0.5,0.219 10 false GND 3.719,1.198 4.219,1.417 0.5,0.219 10 false GND 3.875,0.115 4.188,0.313 0.313,0.198 10 false *b 4.406,1.927 4.719,2.125 0.313,0.198 10 false *c 5.385,1.938 5.698,2.135 0.313,0.198 10 false *d
*a Component with harness connected
(Door Control Receiver)
*b Waveform 1
*c Before lock or unlock button of electrical key transmitter sub-assembly pressed *d After lock or unlock button of electrical key transmitter sub-assembly pressed


OK:
Tester Connection Condition Tool Setting Specified Condition
F46-5 (DATA) - F46-1 (GND) Procedure:
1.

Engine switch off

2.

All doors locked

3.

Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed


5 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)


Result:
Result Proceed to
OK A
NG (for Sedan) B
NG (for Hatchback) C




A

41.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

C

41.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

42.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
42.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>OPERATION CHECK

OK:

Wireless door lock functions operate normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

43.CHECK LIGHTING SYSTEM (INT) OPERATION
a.

Check illuminated entry operation.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>OPERATION CHECK


Result:
Result Proceed to
OK A
Abnormality when driver door opened B
Abnormality when door other than driver door opened C



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

44.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FR DRIVER DOOR)

C

47.READ VALUE USING GTS
44.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FR DRIVER DOOR)
a.

Remove the front door courtesy light switch assembly (for driver door).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly (for driver door).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Result
OK
NG



OK

45.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR DRIVER DOOR)

45.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect 6M driver side junction block assembly connector.


b.

for LHD:

i.

Disconnect the F31 front door courtesy light switch assembly LH connector.



c.

for RHD:

i.

Disconnect the F32 front door courtesy light switch assembly RH connector.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F31-1 - 6M-2 Always Below 1 Ω
F31-1 or 6M-2 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F32-1 - 6M-2 Always Below 1 Ω
F32-1 or 6M-2 - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

46.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

46.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

b.

Disconnect the 6M driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

B343154C28
2.531,0.625 2.823,0.802 0.292,0.177 5.552,0.51 5.844,0.688 0.292,0.177 2.271,1.448 2.229,1.156 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 2.573,0.635 2.885,0.833 0.313,0.198 10 false MB 5.615,0.521 5.927,0.719 0.313,0.198 10 false 6M 2.094,1.458 2.583,1.646 0.49,0.188 10 false DCTY
*a Component without harness connected (Driver Side Junction Block Assembly) - -


Standard Resistance:
Tester Connection Condition Specified Condition
6M-2 - MB-18 (DCTY) Always Below 1 Ω
6M-4 - MB-18 (DCTY) Always Below 1 Ω



Result:
Result
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

47.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door All (Except for Driver Side Seat) Door courtesy signal for any door other than driver door OPEN or CLOSE OPEN: Any door other than driver door open
CLOSE: Any door other than driver door closed
-
Body Electrical > Combination Meter > Data List
Tester Display
Door All (Except for Driver Side Seat)
50003 122 122
OK:

Normal conditions listed above are displayed.



Result:
Result Proceed to
OK A
Abnormality only when front passenger door opened/closed B
Abnormality only when right rear door opened/closed C
Abnormality only when left rear door opened/closed D



A

48.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY COMPUTER)

B

49.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR PASSENGER DOOR)

C

51.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

D

53.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
48.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY COMPUTER)
a.

Disconnect F38 combination meter assembly connector.


b.

Disconnect F52 body computer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-29 (ACTY) - F52-14 (PCTY) Always Below 1 Ω
F38-29 (ACTY) or F52-14 (PCTY) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

49.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR PASSENGER DOOR)
a.

Remove the front door courtesy light switch assembly (for front passenger door).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly (for front passenger door).

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Result
OK
NG



OK

50.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR PASSENGER DOOR) - COMBINATION METER ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR PASSENGER DOOR)

50.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR PASSENGER DOOR) - COMBINATION METER ASSEMBLY)
a.

Disconnect F38 combination meter assembly connector.


b.

for LHD:

i.

Disconnect the F32 front door courtesy light switch assembly RH connector.



c.

for RHD:

i.

Disconnect the F31 front door courtesy light switch assembly LH connector.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
F32-1 - F38-31 (PCTY) Always Below 1 Ω
F32-1 or F38-31 (PCTY) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
F31-1 - F38-31 (PCTY) Always Below 1 Ω
F31-1 or F38-31 (PCTY) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

51.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Remove the rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION


Result:
Result
OK
NG



OK

52.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - COMBINATION METER ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

52.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - COMBINATION METER ASSEMBLY)
a.

Disconnect F38 combination meter assembly connector.


b.

Disconnect the F34 rear door courtesy light switch assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-1 - F38-33 (RRCY) Always Below 1 Ω
F34-1 or F38-33 (RRCY) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

53.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Remove the rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION


Result:
Result
OK
NG



OK

54.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - COMBINATION METER ASSEMBLY)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

54.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - COMBINATION METER ASSEMBLY)
a.

Disconnect F38 combination meter assembly connector.


b.

Disconnect the F33 rear door courtesy light switch assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F33-1 - F38-32 (RLCY) Always Below 1 Ω
F33-1 or F38-32 (RLCY) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR