48725G
1.INSTALL REAR AXLE CARRIER BUSH LH
| *a | Upper Side |
| *b | Front Side |
| *c | 7 to 13° |
| *d | Alignment Mark |
Align the alignment mark on a new rear axle carrier bush LH with the matchmark on the rear axle beam assembly and temporarily install the rear axle carrier bush LH to the rear axle beam assembly.
When the rear axle beam assembly is replaced with a new one, there is no matchmark, so install the rear axle carrier bush LH as shown in the illustration.
| *a | Hold |
| *b | Turn |
Using SST, install the rear axle carrier bush LH to the rear axle beam assembly.
Do not damage the rubber portion when installing the rear axle carrier bush LH.
Apply grease to the threads and tip of the SST center bolt before use.
Apply paint to any scratches on the rear axle beam assembly.
48725F
2.INSTALL REAR AXLE CARRIER BUSH RH
Use the same procedure described for the LH side.
42110F
3.TEMPORARILY INSTALL REAR AXLE BEAM ASSEMBLY
Slowly jack up the rear axle beam assembly with an engine lifter using 4 plate lift attachments or equivalent tools and temporarily install the rear axle beam assembly to the body with the 2 bolts B.
| *a | Plate Lift Attachment | *b | Engine Lifter |
Make sure to secure the rear axle beam assembly to prevent it from dropping.
Temporarily install the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts A.
48231B
4.INSTALL REAR COIL SPRING LH
48231A
5.INSTALL REAR COIL SPRING RH
Use the same procedure described for the LH side.
42450B
6.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH
42450A
7.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH
Use the same procedure described for the LH side.
8.INSPECT REAR AXLE HUB AND BEARING LOOSENESS
9.INSPECT REAR AXLE HUB AND BEARING RUNOUT
10.INSTALL REAR DISC
11.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH
12.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH
Use the same procedure described for the LH side.
46430
13.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
14.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY
Use the same procedure described for the No. 3 parking brake cable assembly.
58251D
15.INSTALL FRONT FLOOR PANEL BRACE LH
58251D
16.INSTALL FRONT FLOOR PANEL BRACE RH
Use the same procedure described for the LH side.
47324
17.INSTALL REAR NO. 4 BRAKE TUBE
Install the rear flexible hose with a new clip.
Using a 10 mm union nut wrench, install the rear No. 4 brake tube while holding the rear flexible hose with a wrench.
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
47323
18.INSTALL REAR NO. 3 BRAKE TUBE
Use the same procedure described for the rear No. 4 brake tube.
47319F
19.INSTALL REAR FLEXIBLE HOSE LH
47318F
20.INSTALL REAR FLEXIBLE HOSE RH
Use the same procedure described for the LH side.
89516D
21.INSTALL SKID CONTROL SENSOR WIRE LH
89516C
22.INSTALL SKID CONTROL SENSOR WIRE RH
Use the same procedure described for the LH side.
23.BLEED BRAKE LINE
24.INSTALL REAR WHEELS
25.INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL
58910C
26.INSTALL REAR CONSOLE BOX ASSEMBLY
27.STABILIZE SUSPENSION
42110F
28.TIGHTEN REAR AXLE BEAM ASSEMBLY
48540
29.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH
48530
30.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH
Use the same procedure described for the LH side.
31.INSPECT REAR WHEEL ALIGNMENT
32.CHECK FOR SPEED SENSOR SIGNAL (w/ ABS)
33.CHECK FOR SPEED SENSOR SIGNAL (w/ VSC)