Home › Suspension › REAR SUSPENSION › REAR AXLE BEAM(for Rear Drum Brake) › from 2018.01
RM30M0E _53 Suspension _017096 REAR SUSPENSION _0090106 REAR AXLE BEAM(for Rear Drum Brake) A

REAR SUSPENSION  REAR AXLE BEAM(for Rear Drum Brake)  INSTALLATION  


PROCEDURE

Hide 48725G 1.INSTALL REAR AXLE CARRIER BUSH LH

a.
C285299C01
2.01,1.573 2.573,1.396 true 1.635,0.094 1.948,0.25 0.313,0.156 10 false *a 0.625,0.969 0.938,1.125 0.313,0.156 10 false *b 1.948,1.958 2.26,2.115 0.313,0.156 10 false *c 2.667,1.292 2.896,1.469 0.229,0.177 10 false *d
*a Upper Side
*b Front Side
*c 7 to 13°
*d Alignment Mark


Align the alignment mark on a new rear axle carrier bush LH with the matchmark on the rear axle beam assembly and temporarily install the rear axle carrier bush LH to the rear axle beam assembly.

NOTICE:

When the rear axle beam assembly is replaced with a new one, there is no matchmark, so install the rear axle carrier bush LH as shown in the illustration.



b.
C292930C01
1.323,1.656 2.354,1.823 2.354,1.823 1.427,1.5 true 0.469,2 0.354,2.51 0.354,2.51 1.021,2.271 true 0.958,0.563 1.271,0.719 0.313,0.156 10 false *a 2.833,0.729 3.146,0.885 0.313,0.156 10 false *b 2.417,1.781 2.875,1.979 0.458,0.198 10 false SST 0.042,2.448 0.5,2.646 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, install the rear axle carrier bush LH to the rear axle beam assembly.

SST
09223-15020  
09710-30012  (09710-04101)
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04030, 09955-04051, 09957-04010, 09958-04011)
09950-60020  (09951-00680)

NOTICE:
·

Do not damage the rubber portion when installing the rear axle carrier bush LH.

·

Apply grease to the threads and tip of the SST center bolt before use.

·

Apply paint to any scratches on the rear axle beam assembly.




Hide 48725F 2.INSTALL REAR AXLE CARRIER BUSH RH

HINT:

Use the same procedure described for the LH side.


Hide 42110F 3.TEMPORARILY INSTALL REAR AXLE BEAM ASSEMBLY

a.

Slowly jack up the rear axle beam assembly with an engine lifter using 4 plate lift attachments or equivalent tools and temporarily install the rear axle beam assembly to the body with the 2 bolts B.

C282509C01
2.073,2.417 2.438,2.052 false 2.49,1.656 2.271,1.75 false 3.323,1.688 3.125,1.688 false 4.052,1.698 3.854,1.698 false 5.063,1.719 4.823,1.625 false 2.51,1.542 2.74,1.698 0.229,0.156 10 true *a 1.896,2.344 2.208,2.5 0.313,0.156 10 false *b 3.344,1.625 3.573,1.781 0.229,0.156 10 true *a 3.698,1.615 3.927,1.771 0.229,0.156 10 true *a 4.656,1.542 4.885,1.698 0.229,0.156 10 true *a 1.865,1.781 1.99,1.927 0.125,0.146 10 true A 5.333,1.771 5.458,1.917 0.125,0.146 10 true A 0.271,1.938 0.396,2.083 0.125,0.146 10 true B 6.875,1.948 7,2.094 0.125,0.146 10 true B
*a Plate Lift Attachment *b Engine Lifter


NOTICE:

Make sure to secure the rear axle beam assembly to prevent it from dropping.



b.

Temporarily install the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts A.


Hide 48231B 4.INSTALL REAR COIL SPRING LH

Hide 48231A 5.INSTALL REAR COIL SPRING RH

HINT:

Use the same procedure described for the LH side.


Hide 42450B 6.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH

Hide 42450A 7.INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 42403 10.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

Hide 58251D 11.INSTALL FRONT FLOOR PANEL BRACE LH

Hide 58251D 12.INSTALL FRONT FLOOR PANEL BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 46430 13.INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

Hide 46420 14.INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Use the same procedure described for the No. 3 parking brake cable assembly.


Hide 47319F 15.INSTALL REAR FLEXIBLE HOSE LH

Hide 47318F 16.INSTALL REAR FLEXIBLE HOSE RH

HINT:

Use the same procedure described for the LH side.


Hide 89516D 17.INSTALL SKID CONTROL SENSOR WIRE LH

Hide 89516C 18.INSTALL SKID CONTROL SENSOR WIRE RH

HINT:

Use the same procedure described for the LH side.


Hide 20.INSTALL REAR WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 21.INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL

Hide 58910C 22.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 42110F 24.TIGHTEN REAR AXLE BEAM ASSEMBLY

Hide 48540 25.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

Hide 48530 26.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.