When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P030000 | Random/Multiple Cylinder Misfire Detected | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored | SAE: P0300 |
| P030027 | Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold | An emission deterioration misfire occurs (2 trip detection logic). | ·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on | DTC stored | SAE: - |
| P030085 | Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range | A misfire occurs that may damage the three-way catalytic converter (2 trip detection logic). | ·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored | SAE: - |
| P030100 | Cylinder 1 Misfire Detected | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored | SAE: P0301 |
| P030200 | Cylinder 2 Misfire Detected | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored | SAE: P0302 |
| P030300 | Cylinder 3 Misfire Detected | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter sub-assembly ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
DTC stored | SAE: P0303 |
When DTCs for misfiring cylinders are randomly stored, but DTC P030000 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P030000 is only stored when several misfiring cylinders are detected at the same time.
The ECM illuminates the MIL and stores a DTC when the following condition, which could cause emission deterioration, is detected (2 trip detection logic).
An excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when the following condition, which could cause damage to the three-way catalytic converter, is detected.
At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
| Required Sensors/Components (Main) | Crankshaft position sensor
Camshaft position sensor |
| Required Sensors/Components (Related) | Engine coolant temperature
Intake air temperature sensor (mass air flow meter sub-assembly) Mass air flow meter sub-assembly |
| Frequency of Operation | Continuous |
| Either of the following conditions is met | (a) or (b) |
| (a) Engine coolant temperature at engine start | Higher than -7°C (19°F) |
| (b) Engine coolant temperature | Higher than 20°C (68°F) |
| Monitor period | Crankshaft 1000 revolutions x 4 |
| Monitor period | Crankshaft 200 revolutions x 3 |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Record the DTC(s) and Freeze Frame Data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Using the GTS, switch the ECM from normal mode to check mode.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE
Start the engine.
Read the misfire counts of each cylinder, Misfire Count Cylinder #1 to Misfire Count Cylinder #3, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the Freeze Frame Data. Perform this step several times.
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.
| Engine speed | Duration |
|---|---|
| Idling | 8.0 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
Check whether misfires have occurred by checking DTCs and Freeze Frame Data.
Do not turn the ignition switch off until the output DTC(s) and Freeze Frame Data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), Freeze Frame Data and other data are cleared.
Record the DTC(s), Freeze Frame Data and misfire counts.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Refer to DTC P010012 for the mass air flow meter sub-assembly circuit.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P010012
Inspect the fuses for circuits related to this system before performing the following procedure.
Check the "Fuel Cut Elapsed Time" in the Data List or the Freeze Frame Data.
If the elapsed time is over 0 seconds, then the engine speed is high (engine speed at which fuel cut occurs + 500 rpm).
When this has happened, there is the possibility that the No. 1 valve rocker arm sub-assembly will become loose and a fire could start, so check that the No. 1 valve rocker arm sub-assembly is properly attached.
By clearing the DTCs, "Fuel Cut Elapsed Time" will be cleared.
In the past, when the primary ignition system (the igniter drive circuit in the ECM, the primary circuit in the ignition coil assembly, the related wire harness, or the connector) was out of order, diagnostic codes from P035113 to P035313 were output. However, these codes are not output in this vehicle.
When a failure in the primary ignition system is suspected, refer to "Catalyst OT Misfire Fuel Cut History", "Catalyst OT Misfire Fuel Cut Cylinder #1 to #3", and "Misfire Count Cylinder #1 to #3" in the Freeze Frame Data, the pending Freeze Frame Data, and the Data List, and confirm in which cylinder the high-frequency misfire was concentrated.
Referring to the following contents of the Freeze Frame Data (or the pending Freeze Frame Data) enables an estimation of which cylinder has misfired and to what degree.
Misfire Count Cylinder #1 to #3: Misfire count according to cylinder.
Catalyst OT Misfire Fuel Cut Cylinder #1 to #3: This expresses a high-frequency misfire was concentrated in a certain cylinder and that cylinder's fuel injection was stopped.
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as Freeze Frame Data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as Freeze Frame Data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
There was insufficient fuel in the tank.
Improper fuel was used.
The spark plugs have been contaminated.
The problem requires further diagnosis.
After finishing repairs, check the misfire counts of the cylinders (Misfire Count Cylinder #1 to Misfire Count Cylinder #3).
Be sure to confirm that no misfiring cylinder DTCs are stored again by performing the confirmation driving pattern after finishing repairs.
When one of Short FT B1S1, Long FT B1S1 in the Freeze Frame Data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (+20% or higher).
When Coolant Temperature in the Freeze Frame Data is below 75°C (167°F), the misfires have occurred only while warming up the engine.
Vehicle body vibration caused by an extremely imbalanced drive wheel may cause misfire DTCs to be stored.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P030000, P030027, P030085, P030100, P030200 or P030300 and other DTCs are output | A |
| P030000, P030027, P030085, P030100, P030200 or P030300 is output | B |
If any DTCs other than DTC P030000, P030027, P030085, P030100, P030200 and P030300 are output, troubleshoot those DTCs first.
A
B
Pre-procedure1
None.
Procedure1
Check the PCV hose connections.
Check the PCV valve.
PCV hose and PCV valve are connected correctly and are not damaged.
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read and note the Misfire RPM and Misfire Load values.
| Tester Display |
|---|
| Misfire RPM |
| Misfire Load |
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
| Proceed to |
|---|
| NEXT |
NEXT
Read the value displayed on the GTS.
| Tester Display |
|---|
| Catalyst OT Misfire Fuel Cut |
| Data List | Result | Proceed to |
|---|---|---|
| Catalyst OT Misfire Fuel Cut | Avail | A |
| Not Avil | B |
A
B
Using the GTS, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.
| Freeze Frame Data Item | Result | Proceed to |
|---|---|---|
| Catalyst OT Misfire Fuel Cut History | ON | A |
| OFF | B |
A
B
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Procedure1
Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #3 displayed on the GTS while performing the Active Test.
| Active Test Display |
|---|
| Prohibit the Catalyst OT Misfire Prevent Fuel Cut |
| Data List Display |
|---|
| Misfire Count Cylinder #1 |
| Misfire Count Cylinder #2 |
| Misfire Count Cylinder #3 |
| Catalyst OT Misfire Fuel Cut |
Post-procedure1
None.
| Misfire Count | Proceed to |
|---|---|
| 1 cylinder have misfire counts | A |
| 2 cylinders or more have misfire counts | A |
| There are no misfire counts | B |
A
B
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Procedure1
According to the display on the GTS, read the Data List. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
| Tester Display |
|---|
| Coolant Temperature |
| Misfire Count Cylinder #1 |
| Misfire Count Cylinder #2 |
| Misfire Count Cylinder #3 |
Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].
Read the Misfire Count Cylinder #1 to Misfire Count Cylinder #3 or DTCs displayed on the GTS [B].
Post-procedure1
None.
| Misfire Count | Proceed to |
|---|---|
| 1 cylinder have misfire counts | A |
| 2 cylinders or more have misfire counts | A |
| There are no misfire counts | B |
A
B
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Perform a spark test.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
OK
NG
Pre-procedure1
Remove the cylinder head cover sub-assembly.
Procedure1
| *a | Timing Mark |
| *b | TDC Timing Mark |
| *c | Groove |
Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
If the timing marks are not as shown, turn the crankshaft one revolution clockwise.
Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>M15A-FKS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Read the Data List twice, when the engine is both cold and warmed up.
| Tester Display |
|---|
| Coolant Temperature |
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temperature | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off and shift position N.
Procedure1
Read Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
| Coolant Temperature |
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| The value of Mass air Flow Sensor is between 4.0 gm/sec and 8.0 gm/sec | A |
| None of the above conditions are met | B |
A
B
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.
The A/C switch and all accessories should be off.
Procedure1
Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.
| Active Test Display |
|---|
| Control the EGR Step Position |
| Data List Display |
|---|
| Engine Speed |
| Intake Manifold Absolute Pressure |
| Coolant Temperature |
| EGR Step Position |
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.
| - | Control the EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stalls |
| Intake Manifold Absolute Pressure
(Data List) |
Intake Manifold Absolute Pressure value is 18 to 38 kPa(abs)
(2.6 to 5.5 psi(abs)) (EGR valve is fully closed) |
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed |
During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Remove the EGR valve assembly.
Procedure1
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (EMISSION CONTROL)>EGR VALVE>REMOVAL
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Remove the cylinder head cover sub-assembly.
| *a | Timing Mark |
| *b | TDC Timing Mark |
| *c | Groove |
Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.
Procedure1
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
If the timing marks are not as shown, turn the crankshaft one revolution clockwise.
Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>M15A-FKS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List twice, when the engine is both cold and warmed up.
| Tester Display |
|---|
| Coolant Temperature |
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temperature | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off and shift position N.
Procedure1
Read Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
| Coolant Temperature |
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| The value of Mass air Flow Sensor is between 4.0 gm/sec and 8.0 gm/sec | A |
| None of the above conditions are met | B |
A
B
Inspect the spark plug of the misfiring cylinder.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Perform a spark test.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
OK
NG
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.
Repair any problems.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Perform the All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P030000, P030027, P030085, P030100, P030200 or P030300.
Check the DTC judgment result.
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200 and/or P030300 is output) |
B |
A
B
Pre-procedure1
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D23-4 (VCC) - D51-78 (VCVG) | Always | Below 1 Ω |
| D23-3 (FG) - D51-101 (VG) | Always | Below 1 Ω |
| D23-2 (E2G) - D51-79 (E2G) | Always | Below 1 Ω |
| D23-4 (VCC) or D51-78 (VCVG) - Body ground and other terminals | Always | 10 kΩ or higher |
| D23-3 (FG) or D51-101 (VG) - Body ground and other terminals | Always | 10 kΩ or higher |
| D23-2 (E2G) or D51-79 (E2G) - Body ground and other terminals | Always | 10 kΩ or higher |
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If the result of the inspection performed in steps 17 and 25 (READ VALUE USING GTS (MASS AIR FLOW SENSOR)) indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Perform the All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P030000, P030027, P030085, P030100, P030200 or P030300.
Check the DTC judgment result.
Post-procedure1
None.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200 and/or P030300 is output) |
B |
A
B