Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM J

M15A-FXE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the auxiliary battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A270193E17
1.313,0.833 2.615,1.031 1.302,0.198 10 false from EFI NO. 1 Fuse 0.885,1.177 2.656,1.396 1.771,0.219 10 false from EFI-MAIN NO. 1 Relay 0.135,1.969 2.625,2.469 2.49,0.5 10 false to Throttle Position Sensor, Accelerator Pedal Sensor Assembly, etc. (Sensors which have an IC) 0.135,2.646 2.563,3.031 2.427,0.385 10 false to Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.969,3.094 5.313,3.406 0.344,0.313 10 false ECM 2.885,0.677 3.563,1 0.677,0.323 10 false BATT 2.823,1.042 3.49,1.292 0.667,0.25 10 false +B, +B2 3.135,2.073 3.5,2.302 0.365,0.229 10 false VC 4.396,0.875 6.188,1.229 1.792,0.354 10 false 5 V Constant Voltage Circuit 5.365,1.76 6.354,2.115 0.99,0.354 10 false Microprocessor 4.073,2.844 4.333,3.063 0.26,0.219 10 false R

When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.

WIRING DIAGRAM

·

For the circuit diagram of the ECM power source refer to the ECM power source circuit.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit

·

VC Output Circuit

A404772E04
0.542,0.354 0.854,0.552 0.313,0.198 10 false D18 0.552,0.542 2.073,0.927 1.521,0.385 10 false Throttle Body with Motor Assembly 0.531,2.208 0.844,2.406 0.313,0.198 10 false e4 0.521,2.385 2.302,2.604 1.781,0.219 10 false Crankshaft Position Sensor 0.552,3.833 0.865,4.031 0.313,0.198 10 false D7 0.552,4.01 2.167,4.396 1.615,0.385 10 false Camshaft Position Sensor (for Intake Camshaft) 0.542,5.354 0.854,5.552 0.313,0.198 10 false D8 0.542,5.542 2.156,5.927 1.615,0.385 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.542,6.906 0.885,7.115 0.344,0.208 10 false D20 0.552,7.094 2.26,7.458 1.708,0.365 10 false Manifold Absolute Pressure Sensor 2.531,0.417 2.781,0.583 0.25,0.167 10 false VC 2.552,0.771 2.771,0.948 0.219,0.177 10 false E2 2.458,1.135 2.781,1.323 0.323,0.188 10 false VTA 2.396,1.5 2.771,1.677 0.375,0.177 10 false VTA2 2.865,0.635 3.115,0.802 0.25,0.167 10 false 4 2.865,0.281 3.115,0.448 0.25,0.167 10 false 2 2.854,1.01 3.104,1.177 0.25,0.167 10 false 1 2.865,1.375 3.115,1.542 0.25,0.167 10 false 3 2.865,2.146 3.115,2.313 0.25,0.167 10 false 3 2.865,2.51 3.115,2.677 0.25,0.167 10 false 2 2.865,2.896 3.115,3.063 0.25,0.167 10 false 1 2.875,3.677 3.125,3.844 0.25,0.167 10 false 3 2.875,4.031 3.125,4.198 0.25,0.167 10 false 2 2.875,4.417 3.125,4.583 0.25,0.167 10 false 1 2.854,5.26 3.104,5.427 0.25,0.167 10 false 3 2.854,6.021 3.104,6.188 0.25,0.167 10 false 1 2.854,5.615 3.104,5.781 0.25,0.167 10 false 2 2.865,6.802 3.115,6.969 0.25,0.167 10 false 3 2.865,7.531 3.115,7.698 0.25,0.167 10 false 2 2.854,7.146 3.104,7.313 0.25,0.167 10 false 1 2.344,2.281 2.76,2.458 0.417,0.177 10 false VCNE 2.458,2.625 2.75,2.802 0.292,0.177 10 false NE- 2.438,2.99 2.75,3.167 0.313,0.177 10 false NE+ 2.479,3.802 2.729,3.969 0.25,0.167 10 false VC 2.427,4.167 2.75,4.354 0.323,0.188 10 false VVI- 2.417,4.531 2.74,4.719 0.323,0.188 10 false VVI+ 2.469,5.375 2.781,5.552 0.313,0.177 10 false VC2 2.406,5.729 2.792,5.917 0.385,0.188 10 false VVE- 2.365,6.115 2.865,6.302 0.5,0.188 10 false VVE+ 2.521,7.281 2.74,7.458 0.219,0.177 10 false E2 2.469,7.635 2.75,7.813 0.281,0.177 10 false PIM 2.531,6.917 2.781,7.083 0.25,0.167 10 false VC 4.948,0.292 5.219,0.458 0.271,0.167 10 false 134 4.948,0.656 5.219,0.823 0.271,0.167 10 false 133 4.948,1.021 5.219,1.188 0.271,0.167 10 false 135 4.948,1.385 5.333,1.677 0.385,0.292 10 false 101 5.021,2.177 5.292,2.344 0.271,0.167 10 false 82 4.948,2.521 5.219,2.688 0.271,0.167 10 false 114 4.948,2.896 5.25,3.177 0.302,0.281 10 false 113 5,3.698 5.198,3.865 0.198,0.167 10 false 83 5,4.063 5.198,4.229 0.198,0.167 10 false 84 5,4.438 5.198,4.604 0.198,0.167 10 false 85 4.917,5.271 5.188,5.438 0.271,0.167 10 false 115 4.927,5.625 5.396,6 0.469,0.375 10 false 116 4.927,6 5.271,6.354 0.344,0.354 10 false 117 5,6.781 5.271,6.948 0.271,0.167 10 false 77 4.99,7.156 5.26,7.323 0.271,0.167 10 false 76 5,7.521 5.271,7.688 0.271,0.167 10 false 78 5.677,8.219 5.979,8.396 0.302,0.177 10 false D52 5.656,8.365 6,8.542 0.344,0.177 10 false ECM 6.271,0.146 6.542,0.313 0.271,0.167 10 false 5 V 5.281,0.302 5.688,0.479 0.406,0.177 10 false VCTA 5.281,0.656 5.604,0.833 0.323,0.177 10 false ETA 5.281,1.125 5.667,1.313 0.385,0.188 10 false VTA1 5.292,1.5 5.677,1.688 0.385,0.188 10 false VTA2 5.281,2.156 5.708,2.333 0.427,0.177 10 false VCNE 5.281,2.521 5.594,2.698 0.313,0.177 10 false NE- 5.292,3.01 5.604,3.188 0.313,0.177 10 false NE+ 5.292,3.698 5.719,3.875 0.427,0.177 10 false VCV1 5.292,4.063 5.719,4.24 0.427,0.177 10 false VV1- 5.292,4.531 5.719,4.708 0.427,0.177 10 false VV1+ 5.313,5.26 5.74,5.438 0.427,0.177 10 false VCE1 5.313,5.625 5.74,5.802 0.427,0.177 10 false EV1- 5.313,6.125 5.74,6.302 0.427,0.177 10 false EV1+ 5.323,6.792 5.781,6.979 0.458,0.188 10 false VCPM 5.323,7.167 5.74,7.344 0.417,0.177 10 false EPIM 5.323,7.625 5.646,7.813 0.323,0.188 10 false PIM

A457721E01
0.646,2.719 1.104,2.917 0.458,0.198 10 false D23 0.667,2.896 2.042,3.323 1.375,0.427 10 false Mass Air Flow Meter 0.615,4.708 1.073,4.906 0.458,0.198 10 false E4 0.625,4.875 2.146,5.427 1.521,0.552 10 false Fuel Pressure Sensor 2.406,2.708 2.74,2.896 0.333,0.188 10 false VCC 2.417,3.073 2.875,3.271 0.458,0.198 10 false E2G 2.5,3.427 2.958,3.625 0.458,0.198 10 false FG 2.438,3.781 2.896,3.979 0.458,0.198 10 false THA 2.521,0.792 2.979,0.99 0.458,0.198 10 false VC 2.344,1.521 2.802,1.719 0.458,0.198 10 false POUT 2.365,1.875 2.823,2.073 0.458,0.198 10 false TOUT 2.427,1.135 2.885,1.333 0.458,0.198 10 false GND 2.49,5.427 2.948,5.625 0.458,0.198 10 false PFL 2.865,3.302 3.323,3.5 0.458,0.198 10 false 3 2.865,1.021 3.323,1.219 0.458,0.198 10 false 2 2.854,0.667 3.313,0.865 0.458,0.198 10 false 3 2.865,1.385 3.323,1.583 0.458,0.198 10 false 1 2.865,2.573 3.323,2.771 0.458,0.198 10 false 4 2.865,2.948 3.323,3.146 0.458,0.198 10 false 2 2.875,1.76 3.333,1.958 0.458,0.198 10 false 4 2.865,3.677 3.323,3.875 0.458,0.198 10 false 1 4.917,0.667 5.375,0.865 0.458,0.198 10 false 124 4.979,1.021 5.438,1.219 0.458,0.198 10 false 92 4.917,1.417 5.375,1.615 0.458,0.198 10 false 123 4.979,1.771 5.438,1.969 0.458,0.198 10 false 91 4.938,2.958 5.396,3.156 0.458,0.198 10 false 106 4.938,3.323 5.396,3.521 0.458,0.198 10 false 139 4.938,3.677 5.396,3.875 0.458,0.198 10 false 138 4.938,4.573 5.396,4.771 0.458,0.198 10 false 130 4.938,4.958 5.396,5.156 0.458,0.198 10 false 128 4.938,5.313 5.396,5.51 0.458,0.198 10 false 129 5.302,2.958 5.76,3.156 0.458,0.198 10 false E2G 5.302,2.573 5.76,2.771 0.458,0.198 10 false VCVG 5.313,3.438 5.771,3.635 0.458,0.198 10 false VG 5.302,3.802 5.76,4 0.458,0.198 10 false THA 5.281,1.042 5.74,1.24 0.458,0.198 10 false EPEO 5.281,0.677 5.74,0.875 0.458,0.198 10 false VCPE 5.292,1.49 5.75,1.688 0.458,0.198 10 false PEO 5.302,4.594 5.76,4.792 0.458,0.198 10 false VCPF 5.302,4.948 5.76,5.146 0.458,0.198 10 false EPFL 5.313,5.427 5.771,5.625 0.458,0.198 10 false PFL 5.729,6.406 6.188,6.604 0.458,0.198 10 false ECM 5.75,6.198 6.208,6.396 0.458,0.198 10 false D52 0.604,0.823 1.063,1.021 0.458,0.198 10 false D32 2.531,4.708 2.99,4.906 0.458,0.198 10 false VC 2.542,5.052 3,5.25 0.458,0.198 10 false E2 2.854,4.969 3.313,5.167 0.458,0.198 10 false 3 2.854,4.573 3.313,4.771 0.458,0.198 10 false 1 2.854,5.323 3.313,5.521 0.458,0.198 10 false 2 0.615,1.021 2.135,1.51 1.521,0.49 10 false Engine Oil Pressure and Temperature Sensor 4.938,2.583 5.396,2.781 0.458,0.198 10 false 107 5.292,1.854 5.75,2.052 0.458,0.198 10 false THEO


CAUTION / NOTICE / HINT

NOTICE:

Check the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

2.CHECK EFI NO. 2 FUSE VOLTAGE

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.CHECK EFI NO. 2 FUSE VOLTAGE
A459396C01
1.646,1.594 1.354,0.448 1.354,0.448 1.208,0.448 true 0.219,1.104 0.531,1.26 0.313,0.156 10 false *1 1.01,0.375 1.208,0.573 0.198,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 EFI NO. 2 Fuse


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 (EFI NO. 2 fuse) - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Check the fuse with it installed to the No. 1 engine room relay block.

·

If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.




Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)

NG

3.CHECK CONNECTION BETWEEN GTS AND ECM (THROTTLE POSITION SENSOR)
a.

Disconnect the D18 throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

4.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)

B

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



4.CHECK CONNECTION BETWEEN GTS AND ECM (CRANKSHAFT POSITION SENSOR)
a.

Disconnect the e4 crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

5.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

5.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the D7 camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

6.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

6.CHECK CONNECTION BETWEEN GTS AND ECM (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the D20 manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

7.CHECK CONNECTION BETWEEN GTS AND ECM (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the D8 camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

8.CHECK CONNECTION BETWEEN GTS AND ECM (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

8.CHECK CONNECTION BETWEEN GTS AND ECM (ENGINE OIL PRESSURE AND TEMPERATURE SENSOR)
a.

Disconnect the D32 engine oil pressure and temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

9.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)

B

REPLACE ENGINE OIL PRESSURE AND TEMPERATURE SENSOR

9.CHECK CONNECTION BETWEEN GTS AND ECM (FUEL PRESSURE SENSOR)
a.

Disconnect the E4 fuel pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

10.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER)

B

REPLACE FUEL PRESSURE SENSOR

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL PRESSURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pressure sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



10.CHECK CONNECTION BETWEEN GTS AND ECM (MASS AIR FLOW METER)
a.

Disconnect the D23 mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine" item of the Data List.



Result:
Result Proceed to
Communication is not possible A
Communication is possible B



A

11.CHECK HARNESS AND CONNECTOR

B

REPLACE MASS AIR FLOW METER

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



11.CHECK HARNESS AND CONNECTOR
a.

Disconnect the D18 throttle body with motor assembly connector.


b.

Disconnect the e4 crankshaft position sensor connector.


c.

Disconnect the D7 camshaft position sensor (for intake camshaft) connector.


d.

Disconnect the D20 manifold absolute pressure sensor connector.


e.

Disconnect the D8 camshaft position sensor (for exhaust camshaft) connector.


f.

Disconnect the D32 engine oil pressure and temperature sensor connector.


g.

Disconnect the E4 fuel pressure sensor connector.


h.

Disconnect the D23 mass air flow meter connector.


i.

Disconnect the A53 and D52 connectors.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D52-134 (VCTA) - Body ground Always 10 kΩ or higher
D52-82 (VCNE) - Body ground Always 10 kΩ or higher
D52-83 (VCV1) - Body ground Always 10 kΩ or higher
D52-115 (VCE1) - Body ground Always 10 kΩ or higher
D52-77 (VCPM) - Body ground Always 10 kΩ or higher
D52-124 (VCPE) - Body ground Always 10 kΩ or higher
D52-107 (VCVG) - Body ground Always 10 kΩ or higher
D52-130 (VCPF) - Body ground Always 10 kΩ or higher
A53-2 (+B) - 1 (EFI NO. 2 fuse) Always Below 1 Ω
A53-3 (+B2) - 1 (EFI NO. 2 fuse) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR