Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420053 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P1CC81E  Hybrid/EV Battery Stack 1 Voltage Difference Out of Range  P1CC91E  Hybrid/EV Battery Stack 2 Voltage Difference Out of Range  


DESCRIPTION

The HV battery is composed of 48 cells (3.7 V each) in series. The battery ECU assembly monitors difference in voltage of each HV battery cell to detect malfunctions of the HV battery.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1CC81E Hybrid/EV Battery Stack 1 Voltage Difference Out of Range The difference in voltage of each cell of the No. 1 HV supply stack sub-assembly exceeds the specified value.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

Hybrid battery terminal block

·

Battery ECU assembly


Comes on Master Warning:
Comes on
P1CC91E Hybrid/EV Battery Stack 2 Voltage Difference Out of Range The difference in voltage of each cell of the No. 2 HV supply stack sub-assembly exceeds the specified value.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

Hybrid battery terminal block

·

Battery ECU assembly


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P1CC81E Hybrid/EV Battery Cell 1 to 48 Voltage*1
P1CC91E

*1:
No. 1 HV Supply Stack Sub-assembly::

Hybrid Battery Cell 1 to 24 Voltage

No. 2 HV Supply Stack Sub-assembly::

Hybrid Battery Cell 25 to 48 Voltage


The following items can be helpful when performing repairs:

Data List
·

Hybrid/EV Battery Cell 1 to 48 Internal Resistance

·

Hybrid/EV Battery SOC

·

Hybrid/EV Battery Voltage

·

Hybrid/EV Battery Current


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 1 hour or more.

3.

Turn the ignition switch to ON and wait for 10 seconds or more.

4.

Drive the vehicle on urban roads for approximately 10 minutes.

HINT:

This DTC may not be stored if the vehicle is stopped or being driven at a constant speed.


5.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

6.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only P1CC81E or P1CC91E is output A
P1CC81E or P1CC91E is output and DTCs other than the DTCs in the table below are output B
P1CC81E or P1CC91E is output and hybrid battery system DTCs in the table below are output C
P1CC81E or P1CC91E is output and hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

c.

Turn the ignition switch off.



A

2.CHECK DTC

B

2.CHECK DTC

C

D

2.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P1CC81E" is also output. A
"P1CC91E" is also output. B



A

3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

B

15.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P1A001C

Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Not connected securely The terminals are damaged or corroded C



A

4.CHECK FREEZE FRAME DATA

B

CONNECT SECURELY

C

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

4.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

b.

Read the value of freeze frame data items "Hybrid/EV battery cell 1 voltage" through "Hybrid/EV battery cell 24 voltage" for DTC P1CC81E and make a note if the value of any is the lowest voltage value.

Powertrain > HV Battery > Trouble Codes
50001 398

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.CHECK BATTERY ECU ASSEMBLY (GA0 - VA24)
5.CHECK BATTERY ECU ASSEMBLY (GA0 - VA24)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P1A8000

Result:
Result Proceed to
The voltage between the terminals is 50 kΩ or more. A
Other than above B



A

6.CHECK TOTAL DISTANCE DRIVEN

B

14.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY
6.CHECK TOTAL DISTANCE DRIVEN
a.

Read the odometer to check the total distance the vehicle has been driven.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when hybrid battery terminal block replaced = less than 200000 km (124280 mile) *1
Other than above B


HINT:

*1: If the hybrid battery terminal block has been replaced, use the total distance driven since it was replaced.



A

7.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

B

10.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY
7.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

8.SIMULATION TEST
8.SIMULATION TEST

Pre-procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398

Procedure1

b.

Drive the vehicle on urban roads for approximately 10 minutes.


Post-procedure1

c.

None.


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT (HV BATTERY)
9.CHECK DTC OUTPUT (HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

b.

Check if DTCs are output.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P1CC81E is output A
P1CC81E is not output B



Post-procedure1

c.

Turn the ignition switch off.



A

B

END

10.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

11.REPLACE HYBRID BATTERY TERMINAL BLOCK
11.REPLACE HYBRID BATTERY TERMINAL BLOCK

NEXT

12.SIMULATION TEST
12.SIMULATION TEST

Pre-procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398

Procedure1

b.

Drive the vehicle on urban roads for approximately 10 minutes.


Post-procedure1

c.

None.


Result:
Proceed to
NEXT



NEXT

13.CHECK DTC OUTPUT (HV BATTERY)
13.CHECK DTC OUTPUT (HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

b.

Check if DTCs are output.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P1CC81E is output A
P1CC81E is not output B



Post-procedure1

c.

Turn the ignition switch off.



A

B

END

14.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

15.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P1A001C

Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Not connected securely The terminals are damaged or corroded C



A

16.CHECK FREEZE FRAME DATA

B

CONNECT SECURELY

C

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

16.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

b.

Read the value of freeze frame data items "Hybrid/EV battery cell 25 voltage" through "Hybrid/EV battery cell 48 voltage" for DTC P1CC91E and make a note if the value of any is the lowest voltage value.

Powertrain > HV Battery > Trouble Codes
50001 398

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

17.CHECK BATTERY ECU ASSEMBLY (GA1 to VA48)
17.CHECK BATTERY ECU ASSEMBLY (GA1 to VA48)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P1A8000

Result:
Result Proceed to
The voltage between the terminals is 50 kΩ or more. A
Other than above B



A

18.CHECK TOTAL DISTANCE DRIVEN

B

26.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY
18.CHECK TOTAL DISTANCE DRIVEN
a.

Read the odometer to check the total distance the vehicle has been driven.


Result:
Result Proceed to
Total distance driven is less than 200000 km (124280 mile) A
Total distance driven is 200000 km (124280 mile) or more Current total distance driven - total distance driven when hybrid battery terminal block replaced = less than 200000 km (124280 mile) *1
Other than above B


HINT:

*1: If the hybrid battery terminal block has been replaced, use the total distance driven since it was replaced.



A

19.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

B

22.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY
19.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

20.SIMULATION TEST
20.SIMULATION TEST

Pre-procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398

Procedure1

b.

Drive the vehicle on urban roads for approximately 10 minutes.


Post-procedure1

c.

None.


Result:
Proceed to
NEXT



NEXT

21.CHECK DTC OUTPUT (HV BATTERY)
21.CHECK DTC OUTPUT (HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

b.

Check if DTCs are output.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P1CC91E is output A
P1CC91E is not output B



Post-procedure1

c.

Turn the ignition switch off.



A

B

END

22.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

23.REPLACE HYBRID BATTERY TERMINAL BLOCK
23.REPLACE HYBRID BATTERY TERMINAL BLOCK

NEXT

24.SIMULATION TEST
24.SIMULATION TEST

Pre-procedure1

a.

Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs
50002 398

Procedure1

b.

Drive the vehicle on urban roads for approximately 10 minutes.


Post-procedure1

c.

None.


Result:
Proceed to
NEXT



NEXT

25.CHECK DTC OUTPUT (HV BATTERY)
25.CHECK DTC OUTPUT (HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

b.

Check if DTCs are output.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P1CC91E is output A
P1CC91E is not output B



Post-procedure1

c.

Turn the ignition switch off.



A

B

END

26.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

NEXT