Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420053 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P33EC16  (Extreme) Hybrid/EV Battery Stack 1 Cell Circuit Voltage Below Threshold  P33ED16  (Extreme) Hybrid/EV Battery Stack 2 Cell Circuit Voltage Below Threshold  


DESCRIPTION

If the voltage of an HV battery cell is lower than the threshold for a certain amount of time, the battery ECU assembly will interpret this as a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P33EC16 (Extreme) Hybrid/EV Battery Stack 1 Cell Circuit Voltage Below Threshold The voltage of any cell of the No. 1 HV supply stack sub-assembly has decreased excessively.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning:
Comes on
P33ED16 (Extreme) Hybrid/EV Battery Stack 2 Cell Circuit Voltage Below Threshold The voltage of any cell of the No. 2 HV supply stack sub-assembly has decreased excessively.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning:
Comes on

CAUTION:

Do not charge the HV battery using the THS charger if DTC P33EC16 or P33ED16 is output.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Drive the vehicle on urban roads for approximately 10 minutes.

4.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P1A001C.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P1A001C

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only P33EC16 or P33ED16 is output A
P33EC16 or P33ED16 is output and DTCs other than the DTCs in the table below are output B
P33EC16 or P33ED16 is output and hybrid battery system DTCs in the table below are output C
P33EC16 or P33ED16 is output and hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

c.

Turn the ignition switch off.



A

2.CHECK DTC

B

2.CHECK DTC

C

D

2.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P33EC16" is also output. A
"P33ED16" is also output. B



A

3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

B

8.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P1A001C

Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Not connected securely The terminals are damaged or corroded C



A

4.CHECK FREEZE FRAME DATA

B

CONNECT SECURELY

C

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

4.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

b.

Read the value of freeze frame data items "Hybrid/EV battery cell 1 voltage" through "Hybrid/EV battery cell 24 voltage" for DTC P33EC16 and make a note if the value of any is 1.2 V or less.

Powertrain > HV Battery > Trouble Codes
50001 398

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

5.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 1 TO 24 VOLTAGE)
5.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 1 TO 24 VOLTAGE)
CAUTION:
·

Be sure to wear insulated gloves and protective goggles.

·

Disconnect only the connector corresponding to the HV battery cell to be checked. Do not disconnect the other connectors.



NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage of each HV battery cell.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458602N01
2.385,0.083 2.74,0.323 0.354,0.24 2.417,0.104 2.719,0.302 0.302,0.198 10 true z15

Disconnect the z15 battery ECU assembly connector.


Procedure1

d.
A459573C01
1.448,0.073 1.875,0.26 0.427,0.188 0.406,2.365 1.458,2.219 true 1.573,1.948 0.385,0.885 true 0.49,2.771 1.563,2.219 true 1.656,1.948 0.823,0.771 true 0.792,2.969 1.656,2.219 true 1.521,0.542 1.792,1.958 true 1.135,3.146 1.771,2.208 true 2.385,0.573 1.896,1.958 true 2.823,0.667 1.979,1.948 true 2.896,1.042 2.083,1.958 true 2.896,1.375 2.188,1.969 true 2.906,1.688 2.302,1.99 true 2.927,2.458 2.281,2.188 true 2.927,2.667 2.188,2.188 true 1.531,3.146 1.865,2.219 true 1.896,3.104 1.958,2.229 true 2.583,3.104 2.073,2.208 true 2.927,2.281 2.313,2.094 true 2.948,2 2.198,2.052 true 2.688,2.844 2.083,2.073 true 2.26,3.125 1.979,2.094 true 1.865,2.063 1.792,0.531 true 1.156,0.573 1.75,2.073 true 1.656,2.083 0.438,1.292 true 0.448,1.75 1.552,2.104 true 0.094,2.313 0.406,2.51 0.313,0.198 10 false GA0 1.521,0.094 1.833,0.292 0.313,0.198 10 false z15 0.135,1.667 0.448,1.865 0.313,0.198 10 false VA2 0.208,2.708 0.521,2.906 0.313,0.198 10 false VA3 0.646,0.635 0.958,0.833 0.313,0.198 10 false VA4 0.135,1.208 0.448,1.406 0.313,0.198 10 false VA5 0.573,3 0.885,3.198 0.313,0.198 10 false VA6 1.385,0.396 1.698,0.594 0.313,0.198 10 false VA7 1.01,0.396 1.323,0.594 0.313,0.198 10 false VA8 1,3.188 1.313,3.385 0.313,0.198 10 false VA9 2.271,0.438 2.667,0.635 0.396,0.198 10 false VA10 1.688,0.406 2.083,0.615 0.396,0.208 10 false VA11 1.375,3.188 1.771,3.385 0.396,0.198 10 false VA12 2.719,0.51 3.115,0.708 0.396,0.198 10 false VA13 2.167,3.167 2.563,3.365 0.396,0.198 10 false VA14 1.76,3.177 2.156,3.375 0.396,0.198 10 false VA15 2.948,0.927 3.344,1.125 0.396,0.198 10 false VA16 2.688,2.885 3.083,3.083 0.396,0.198 10 false VA17 2.563,3.146 2.958,3.344 0.396,0.198 10 false VA18 2.969,1.313 3.365,1.51 0.396,0.198 10 false VA19 2.99,1.938 3.385,2.135 0.396,0.198 10 false VA20 3,2.656 3.396,2.854 0.396,0.198 10 false VA21 2.979,1.625 3.375,1.823 0.396,0.198 10 false VA22 3.01,2.271 3.406,2.469 0.396,0.198 10 false VA23 3.01,2.438 3.406,2.635 0.396,0.198 10 false VA24 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.24,0.75 0.552,0.948 0.313,0.198 10 false VA1
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the HV battery cells whose value in the freeze frame data was 1.2 V or less only.


Tester Connection Hybrid Battery Cell Condition
z15-28 (GA0) - z15-5 (VA1) 1 Always
z15-5 (VA1) - z15-17 (VA2) 2 Always
z15-17 (VA2) - z15-29(VA3) 3 Always
z15-29 (VA3) - z15-6 (VA4) 4 Always
z15-6 (VA4) - z15-18 (VA5) 5 Always
z15-18 (VA5) - z15-30 (VA6) 6 Always
z15-30 (VA6) - z15-7 (VA7) 7 Always
z15-7 (VA7) - z15-19 (VA8) 8 Always
z15-19 (VA8) - z15-31 (VA9) 9 Always
z15-31 (VA9) - z15-8 (VA10) 10 Always
z15-8 (VA10) - z15-20 (VA11) 11 Always
z15-20 (VA11) - z15-32 (VA12) 12 Always
z15-32 (VA12) - z15-9 (VA13) 13 Always
z15-9 (VA13) - z15-21 (VA14) 14 Always
z15-21 (VA14) - z15-33 (VA15) 15 Always
z15-33 (VA15) - z15-10 (VA16) 16 Always
z15-10 (VA16) - z15-22 (VA17) 17 Always
z15-22 (VA17) - z15-34 (VA18) 18 Always
z15-34 (VA18) - z15-11 (VA19) 19 Always
z15-11 (VA19) - z15-23 (VA20) 20 Always
z15-23 (VA20) - z15-35 (VA21) 21 Always
z15-35 (VA21) - z15-12 (VA22) 22 Always
z15-12 (VA22) - z15-24 (VA23) 23 Always
z15-24 (VA23) -z15-36 (VA24) 24 Always

CAUTION:

Make sure not to cross the electrodes of an electrical tester measurement terminals.


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.



Result:
Result Proceed to
The voltage between the terminals is 1.2 V or less. A
Other than above B


Post-procedure1

e.

Reconnect the z15 battery ECU assembly connector.


f.

Install the No. 1 HV battery hose.



A

6.CHECK BATTERY ECU ASSEMBLY (GA0 - VA24)

B

6.CHECK BATTERY ECU ASSEMBLY (GA0 - VA24)
NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance.


Pre-procedure1

a.

Remove the battery ECU assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the HV battery cells which measured 1.2 V or less in the previous step.


A459834C01
5.104,0.448 5.531,0.688 0.427,0.24 4.875,5.74 3.885,5.365 true 4.646,6.063 3.781,5.333 true 3.917,6.125 3.625,5.365 true 3.771,6.354 3.531,5.365 true 3.26,6.365 3.385,5.365 true 3.083,6.125 3.302,5.365 true 1.833,6.25 3.042,5.365 true 1.833,5.75 2.938,5.365 true 1.844,5.281 2.906,5.219 true 1.833,4.677 2.885,5.094 true 1.833,4.083 3.042,5.198 true 2.417,4.302 3.01,5.052 true 2.469,4.063 3.146,5.042 true 2.5,6.104 3.188,5.24 true 2.646,6.333 3.156,5.385 true 2.896,4.292 3.26,5.177 true 3.063,3.979 3.302,5.063 true 3.427,5.229 3.51,6.115 true 3.385,4.354 3.427,5.063 true 3.813,4.302 3.563,5.094 true 4.271,4.063 3.667,5.083 true 4.625,4.417 3.792,5.094 true 3.573,4.031 3.5,5.188 true 4.333,6.417 3.646,5.219 true 5.052,4.948 3.802,5.198 true 0.135,0.052 0.448,0.25 0.313,0.198 10 false *a 1.469,5.677 2.083,5.875 0.615,0.198 10 false VA24 1.469,5.219 2.083,5.417 0.615,0.198 10 false VA23 1.427,4.615 2.042,4.813 0.615,0.198 10 false VA22 1.479,6.198 2.094,6.396 0.615,0.198 10 false VA21 1.479,3.99 2.094,4.188 0.615,0.198 10 false VA20 2.125,4.146 2.74,4.344 0.615,0.198 10 false VA19 2.469,6.406 3.083,6.604 0.615,0.198 10 false VA18 2.26,6.146 2.875,6.344 0.615,0.198 10 false VA17 2.188,3.917 2.802,4.115 0.615,0.198 10 false VA16 2.833,6.156 3.448,6.354 0.615,0.198 10 false VA15 2.656,4.156 3.271,4.354 0.615,0.198 10 false VA14 2.896,3.813 3.51,4.01 0.615,0.198 10 false VA13 3.094,6.406 3.708,6.604 0.615,0.198 10 false VA12 3.375,6.167 3.99,6.365 0.615,0.198 10 false VA11 3.208,4.188 3.823,4.385 0.615,0.198 10 false VA10 3.635,6.406 4.25,6.604 0.615,0.198 10 false VA9 3.479,3.865 4.094,4.063 0.615,0.198 10 false VA8 3.729,4.125 4.344,4.323 0.615,0.198 10 false VA7 3.885,6.188 4.5,6.385 0.615,0.198 10 false VA6 4.25,6.469 4.865,6.667 0.615,0.198 10 false VA5 4.188,3.896 4.802,4.094 0.615,0.198 10 false VA4 4.583,6.094 5.198,6.292 0.615,0.198 10 false VA3 5.125,4.865 5.74,5.063 0.615,0.198 10 false VA2 4.563,4.26 5.177,4.458 0.615,0.198 10 false VA1 4.917,5.781 5.531,5.979 0.615,0.198 10 false GA0 5.177,0.479 5.51,0.656 0.333,0.177 10 true z15
*a Component without harness connected
(Battery ECU Assembly)
- -


Standard Resistance:
Tester Connection
(Tester Probe Polarity)
Hybrid Battery Cell Condition Specified Condition
z15-28 (GA0) (-) - z15-5 (VA1) (+) 1 Always 50 kΩ or more
z15-5 (VA1) (-) - z15-17 (VA2) (+) 2 Always 50 kΩ or more
z15-17 (VA2) (-) - z15-29 (VA3) (+) 3 Always 50 kΩ or more
z15-29 (VA3) (-) - z15-6 (VA4) (+) 4 Always 50 kΩ or more
z15-6 (VA4) (-) - z15-18 (VA5) (+) 5 Always 50 kΩ or more
z15-18 (VA5) (-) - z15-30 (VA6) (+) 6 Always 50 kΩ or more
z15-30 (VA6) (-) - z15-7 (VA7) (+) 7 Always 50 kΩ or more
z15-7 (VA7) (-) - z15-19 (VA8) (+) 8 Always 50 kΩ or more
z15-19 (VA8) (-) - z15-31 (VA9) (+) 9 Always 50 kΩ or more
z15-31 (VA9) (-) - z15-8 (VA10) (+) 10 Always 50 kΩ or more
z15-8 (VA10) (-) - z15-20 (VA11) (+) 11 Always 50 kΩ or more
z15-20 (VA11) (-) - z15-32 (VA12) (+) 12 Always 50 kΩ or more
z15-32 (VA12) (-) - z15-9 (VA13) (+) 13 Always 50 kΩ or more
z15-9 (VA13) (-) - z15-21 (VA14) (+) 14 Always 50 kΩ or more
z15-21 (VA14) (-) - z15-33 (VA15) (+) 15 Always 50 kΩ or more
z15-33 (VA15) (-) - z15-10 (VA16) (+) 16 Always 50 kΩ or more
z15-10 (VA16) (-) - z15-22 (VA17) (+) 17 Always 50 kΩ or more
z15-22 (VA17) (-) - z15-34 (VA18) (+) 18 Always 50 kΩ or more
z15-34 (VA18) (-) - z15-11 (VA19) (+) 19 Always 50 kΩ or more
z15-11 (VA19) (-) - z15-23 (VA20) (+) 20 Always 50 kΩ or more
z15-23 (VA20) (-) - z15-35 (VA21) (+) 21 Always 50 kΩ or more
z15-35 (VA21) (-) - z15-12 (VA22) (+) 22 Always 50 kΩ or more
z15-12 (VA22) (-) - z15-24 (VA23) (+) 23 Always 50 kΩ or more
z15-24 (VA23) (-) - z15-36 (VA24) (+) 24 Always 50 kΩ or more


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Read the resistance after the value has stabilized.

·

In order to avoid damaging the terminals of the battery ECU assembly, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of the battery ECU assembly.




Post-procedure1

c.

Install the battery ECU assembly.


Result:
Result Proceed to
The voltage between the terminals is 50 kΩ or more. A
Other than above B



A

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

B

7.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY
7.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

8.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P1A001C

Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Not connected securely The terminals are damaged or corroded C



A

9.CHECK FREEZE FRAME DATA

B

CONNECT SECURELY

C

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

9.CHECK FREEZE FRAME DATA

Post-procedure1

a.

None.


Procedure1

b.

Read the value of freeze frame data items "Hybrid/EV battery cell 25 voltage" through "Hybrid/EV battery cell 48 voltage" for DTC P33ED16 and make a note if the value of any is 1.2 V or less.

Powertrain > HV Battery > Trouble Codes
50001 398

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

10.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 25 TO 48 VOLTAGE)
10.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 25 TO 48 VOLTAGE)
CAUTION:
·

Be sure to wear insulated gloves and protective goggles.

·

Disconnect only the connector corresponding to the HV battery cell to be checked. Do not disconnect the other connectors.



NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the voltage of each HV battery cell.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A458603N01
1.667,0.135 2.021,0.385 0.354,0.25 1.698,0.167 1.99,0.365 0.292,0.198 10 true z13

Disconnect the z13 battery ECU assembly connector.


Procedure1

d.
A459572C01
1.448,0.073 1.875,0.26 0.427,0.188 0.406,2.365 1.458,2.219 true 1.573,1.948 0.385,0.885 true 0.49,2.771 1.563,2.219 true 1.656,1.948 0.823,0.771 true 0.792,2.969 1.656,2.219 true 1.531,0.479 1.792,1.958 true 1.135,3.146 1.771,2.208 true 2.385,0.573 1.896,1.958 true 2.823,0.667 1.979,1.948 true 2.896,1.042 2.083,1.958 true 2.896,1.375 2.188,1.969 true 2.906,1.688 2.302,1.99 true 2.927,2.458 2.281,2.188 true 2.927,2.667 2.188,2.188 true 1.531,3.146 1.865,2.219 true 1.896,3.104 1.958,2.229 true 2.583,3.104 2.073,2.208 true 2.927,2.281 2.313,2.094 true 2.948,2 2.198,2.052 true 2.688,2.844 2.083,2.073 true 2.26,3.125 1.979,2.094 true 1.865,2.063 1.792,0.531 true 1.156,0.573 1.75,2.073 true 1.656,2.083 0.438,1.292 true 0.448,1.75 1.552,2.104 true 0.094,2.313 0.406,2.51 0.313,0.198 10 false GA1 1.521,0.094 1.833,0.292 0.313,0.198 10 false z13 0.104,1.667 0.625,1.865 0.521,0.198 10 false VA26 0.146,2.719 0.656,2.938 0.51,0.219 10 false VA27 0.646,0.635 1.052,0.833 0.406,0.198 10 false VA28 0.104,1.208 0.563,1.406 0.458,0.198 10 false VA29 0.573,3 0.969,3.198 0.396,0.198 10 false VA30 1.354,0.313 1.865,0.521 0.51,0.208 10 false VA31 1.01,0.396 1.427,0.604 0.417,0.208 10 false VA32 1,3.188 1.396,3.385 0.396,0.198 10 false VA33 2.271,0.438 2.667,0.635 0.396,0.198 10 false VA34 1.688,0.406 2.083,0.615 0.396,0.208 10 false VA35 1.375,3.188 1.771,3.385 0.396,0.198 10 false VA36 2.719,0.51 3.115,0.708 0.396,0.198 10 false VA37 2.167,3.167 2.563,3.365 0.396,0.198 10 false VA38 1.76,3.177 2.156,3.375 0.396,0.198 10 false VA39 2.948,0.927 3.344,1.125 0.396,0.198 10 false VA40 2.688,2.885 3.083,3.083 0.396,0.198 10 false VA41 2.563,3.146 2.958,3.344 0.396,0.198 10 false VA42 2.969,1.313 3.365,1.51 0.396,0.198 10 false VA43 2.99,1.938 3.385,2.135 0.396,0.198 10 false VA44 3,2.656 3.396,2.854 0.396,0.198 10 false VA45 2.979,1.625 3.375,1.823 0.396,0.198 10 false VA46 3.01,2.271 3.406,2.469 0.396,0.198 10 false VA47 3.01,2.438 3.406,2.635 0.396,0.198 10 false VA48 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.208,0.75 0.635,0.948 0.427,0.198 10 false VA25
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage of the HV battery cells whose value in the freeze frame data was 1.2 V or less only.


Tester Connection Hybrid Battery Cell Condition
z13-28 (GA1) - z13-5 (VA25) 25 Always
z13-5 (VA25) - z13-17 (VA26) 26 Always
z13-17 (VA26) - z13-29 (VA27) 27 Always
z13-29 (VA27) - z13-6 (VA28) 28 Always
z13-6 (VA28) - z13-18 (VA29) 29 Always
z13-18 (VA29) - z13-30 (VA30) 30 Always
z13-30 (VA30) - z13-7 (VA31) 31 Always
z13-7 (VA31) - z13-19 (VA32) 32 Always
z13-19 (VA32) - z13-31 (VA33) 33 Always
z13-31 (VA33) - z13-8 (VA34) 34 Always
z13-8 (VA34) - z13-20 (VA35) 35 Always
z13-20 (VA35) - z13-32 (VA36) 36 Always
z13-32 (VA36) - z13-9 (VA37) 37 Always
z13-9 (VA37) - z13-21 (VA38) 38 Always
z13-21 (VA38) - z13-33 (VA39) 39 Always
z13-33 (VA39) - z13-10 (VA40) 40 Always
z13-10 (VA40) - z13-22 (VA41) 41 Always
z13-22 (VA41) - z13-34 (VA42) 42 Always
z13-34 (VA42) - z13-11 (VA43) 43 Always
z13-11 (VA43) - z13-23 (VA44) 44 Always
z13-23 (VA44) - z13-35 (VA45) 45 Always
z13-35 (VA45) - z13-12 (VA46) 46 Always
z13-12 (VA46) - z13-24 (VA47) 47 Always
z13-24 (VA47) - z13-36(VA48) 48 Always

CAUTION:

Make sure not to cross the electrodes of an electrical tester measurement terminals.


NOTICE:

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.



Result:
Result Proceed to
The voltage between the terminals is 1.2 V or less. A
Other than above B


Post-procedure1

e.

Reconnect the z13 battery ECU assembly connector.


f.

Install the No. 1 HV battery hose.



A

11.CHECK BATTERY ECU ASSEMBLY (GA1 to VA48)

B

11.CHECK BATTERY ECU ASSEMBLY (GA1 to VA48)
NOTICE:

Make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance.


Pre-procedure1

a.

Remove the battery ECU assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

HINT:

Only inspect the terminals of the battery ECU assembly which correspond to the HV battery cells which measured 1.2 V or less in the previous step.


A459862C01
3.75,0.448 4.177,0.688 0.427,0.24 4.875,5.74 3.885,5.365 true 4.646,6.063 3.781,5.333 true 3.917,6.125 3.625,5.365 true 3.771,6.354 3.531,5.365 true 3.26,6.365 3.385,5.365 true 3.083,6.125 3.302,5.365 true 1.833,6.25 3.042,5.365 true 1.833,5.75 2.938,5.365 true 1.844,5.281 2.906,5.219 true 1.833,4.677 2.885,5.094 true 1.833,4.083 3.042,5.198 true 2.417,4.302 3.01,5.052 true 2.469,4.063 3.146,5.042 true 2.5,6.104 3.188,5.24 true 2.646,6.333 3.156,5.385 true 2.896,4.292 3.26,5.177 true 3.063,3.979 3.302,5.063 true 3.427,5.229 3.51,6.115 true 3.385,4.354 3.427,5.063 true 3.813,4.302 3.563,5.094 true 4.271,4.063 3.667,5.083 true 4.625,4.417 3.792,5.094 true 3.573,4.031 3.5,5.188 true 4.333,6.417 3.646,5.219 true 5.052,4.948 3.802,5.198 true 0.135,0.052 0.448,0.25 0.313,0.198 10 false *a 1.469,5.677 2.083,5.875 0.615,0.198 10 false VA48 1.469,5.219 2.083,5.417 0.615,0.198 10 false VA47 1.427,4.615 2.042,4.813 0.615,0.198 10 false VA46 1.479,6.198 2.094,6.396 0.615,0.198 10 false VA45 1.479,3.99 2.094,4.188 0.615,0.198 10 false VA44 2.125,4.146 2.74,4.344 0.615,0.198 10 false VA43 2.469,6.406 3.083,6.604 0.615,0.198 10 false VA42 2.26,6.146 2.875,6.344 0.615,0.198 10 false VA41 2.188,3.917 2.802,4.115 0.615,0.198 10 false VA40 2.833,6.156 3.448,6.354 0.615,0.198 10 false VA39 2.656,4.156 3.271,4.354 0.615,0.198 10 false VA38 2.896,3.813 3.51,4.01 0.615,0.198 10 false VA37 3.094,6.406 3.708,6.604 0.615,0.198 10 false VA36 3.375,6.167 3.99,6.365 0.615,0.198 10 false VA35 3.208,4.188 3.823,4.385 0.615,0.198 10 false VA34 3.635,6.406 4.25,6.604 0.615,0.198 10 false VA33 3.479,3.865 4.094,4.063 0.615,0.198 10 false VA32 3.729,4.125 4.344,4.323 0.615,0.198 10 false VA31 3.854,6.188 4.469,6.385 0.615,0.198 10 false VA30 4.25,6.469 4.865,6.667 0.615,0.198 10 false VA29 4.188,3.896 4.802,4.094 0.615,0.198 10 false VA28 4.583,6.094 5.198,6.292 0.615,0.198 10 false VA27 5.125,4.865 5.74,5.063 0.615,0.198 10 false VA26 4.563,4.26 5.177,4.458 0.615,0.198 10 false VA25 4.917,5.781 5.531,5.979 0.615,0.198 10 false GA1 3.813,0.479 4.146,0.656 0.333,0.177 10 true z13
*a Component without harness connected
(Battery ECU Assembly)
- -


Standard Resistance:
Tester Connection
(Tester Probe Polarity)
Hybrid Battery Cell Condition Specified Condition
z13-28 (GA1) (-) - z13-5 (VA25) (+) 25 Always 50 kΩ or more
z13-5 (VA25) (-) - z13-17 (VA26) (+) 26 Always 50 kΩ or more
z13-17 (VA26) (-) - z13-29 (VA27) (+) 27 Always 50 kΩ or more
z13-29 (VA27) (-) - z13-6 (VA28) (+) 28 Always 50 kΩ or more
z13-6 (VA28) (-) - z13-18 (VA29) (+) 29 Always 50 kΩ or more
z13-18 (VA29) (-) - z13-30 (VA30) (+) 30 Always 50 kΩ or more
z13-30 (VA30) (-) - z13-7 (VA31) (+) 31 Always 50 kΩ or more
z13-7 (VA31) (-) - z13-19 (VA32) (+) 32 Always 50 kΩ or more
z13-19 (VA32) (-) - z13-31 (VA33) (+) 33 Always 50 kΩ or more
z13-31 (VA33) (-) - z13-8 (VA34) (+) 34 Always 50 kΩ or more
z13-8 (VA34) (-) - z13-20 (VA35) (+) 35 Always 50 kΩ or more
z13-20 (VA35) (-) - z13-32 (VA36) (+) 36 Always 50 kΩ or more
z13-32 (VA36) (-) - z13-9 (VA37) (+) 37 Always 50 kΩ or more
z13-9 (VA37) (-) - z13-21 (VA38) (+) 38 Always 50 kΩ or more
z13-21 (VA38) (-) - z13-33 (VA39) (+) 39 Always 50 kΩ or more
z13-33 (VA39) (-) - z13-10 (VA40) (+) 40 Always 50 kΩ or more
z13-10 (VA40) (-) - z13-22 (VA41) (+) 41 Always 50 kΩ or more
z13-22 (VA41) (-) - z13-34 (VA42) (+) 42 Always 50 kΩ or more
z13-34 (VA42) (-) - z13-11 (VA43) (+) 43 Always 50 kΩ or more
z13-11 (VA43) (-) - z13-23 (VA44) (+) 44 Always 50 kΩ or more
z13-23 (VA44) (-) - z13-35 (VA45) (+) 45 Always 50 kΩ or more
z13-35 (VA45) (-) - z13-12 (VA46) (+) 46 Always 50 kΩ or more
z13-12 (VA46) (-) - z13-24 (VA47) (+) 47 Always 50 kΩ or more
z13-24 (VA47) (-) - z13-36 (VA48) (+) 48 Always 50 kΩ or more


NOTICE:
·

Make sure to check the polarity of each terminal (positive (+) or negative (-)) before connecting a tester.

·

Read the resistance after the value has stabilized.

·

In order to avoid damaging the terminals of the battery ECU assembly, make sure to use tester probes with a diameter of approximately 0.5 mm (0.0197 in.) when measuring the resistance of the battery ECU assembly.




Post-procedure1

c.

Install the battery ECU assembly.


Result:
Result Proceed to
The voltage between the terminals is 50 kΩ or more. A
Other than above B



A

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

B

12.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY
12.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

NEXT