Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420053 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P0C3000  Hybrid/EV Battery State of Charge High  


DESCRIPTION

The battery ECU assembly monitors the operation of the hybrid battery system and will store this DTC if it detects a malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0C3000 Hybrid/EV Battery State of Charge High Even though charging of the HV battery is prohibited due to the SOC reaching the upper limit, charging continues to be performed due to a hybrid control system malfunction.
(1 trip detection logic)
·

Hybrid vehicle control ECU

·

No. 1 traction battery device box assembly


Does not come on Master Warning:
Comes on

Related Data List
DTC No. Data List
P0C3000
·

Hybrid/EV Battery SOC

·

WIN Control Limit Power

·

Hybrid/EV Battery Current



CONFIRMATION DRIVING PATTERN

HINT:

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Apply the parking brake and secure the wheels using chocks.

4.

Turn the ignition switch to ON (READY), drive (D) selected and the vehicle stopped, firmly depress the brake pedal and accelerator pedal. The engine rpm will increase as well as the value of Data List item "Hybrid/EV Battery SOC". If the value drops, release the accelerator pedal and then depress it again to continue charging.

5.

Check that charging stops when the Data List item "Hybrid/EV Battery SOC" reaches the upper limit.

6.

Enter the following menus: Powertrain / HV battery / Utility / All Readiness.

7.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AA649.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA649

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C83
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.

After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with conver terassembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
Only P0C3000 is output A
P0C3000 and other DTCs are output B



Post-procedure1

c.

Turn the ignition switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
DTCs are not output A
DTCs are output B



Post-procedure1

c.

Turn the ignition switch off.



A

3.CHECK FREEZE FRAME DATA (HV BATTERY)

B

3.CHECK FREEZE FRAME DATA (HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

b.

Read the freeze frame data of DTC P0C3000.

Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
OFF is displayed for "Ready Signal", "SMRP Control Status", "SMRB Control Status" and "SMRG Control Status" and -0.5 A or less is displayed for "Hybrid/EV Battery Current". A
Other than above B


HINT:

As the ignition switch to ON state may cause the DTC to be stored, freeze frame data is used to judge the cause of the DTC output.



Post-procedure1

c.

Turn the ignition switch off.



A

4.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP, SMRB, SMRG)

B

4.INSPECT NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY (SMRP, SMRB, SMRG)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON, unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.

Disconnect the high voltage cable connectors from the No. 1 traction battery device box assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

A449727C09
5.615,0.208 6.021,0.417 0.406,0.208 3.177,0.281 3.531,0.458 0.354,0.177 3.406,0.667 3.938,1.063 true 5.813,0.698 6.292,1.063 true 0.573,0.146 0.885,0.302 0.313,0.156 10 false *a 3.99,1.021 4.448,1.219 0.458,0.198 10 false CBI 5.698,0.229 5.99,0.385 0.292,0.156 10 true z10 6.375,1.031 6.531,1.229 0.156,0.198 10 false + 3.271,0.292 3.479,0.458 0.208,0.167 10 true a1
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance (SMRB):
Tester Connection Condition Specified Condition
a1-1 (CBI) - z10-1 (+) Ignition switch off 10 kΩ or higher



e.

Measure the resistance according to the value(s) in the table below.

A449727C10
2.219,0.271 2.583,0.458 0.365,0.188 1.167,0.115 1.531,0.323 0.365,0.208 2.063,1.063 2.396,0.677 true 0.833,0.854 1.344,0.656 true 0.271,0.094 0.594,0.531 0.323,0.438 10 false *a 2.313,0.292 2.531,0.448 0.219,0.156 10 true a2 1.271,0.135 1.49,0.292 0.219,0.156 10 true z9 1.813,1 2.188,1.208 0.375,0.208 10 false CEI 0.719,0.781 0.875,0.979 0.156,0.198 10 false -
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)
- -


Standard Resistance (SMRG, SMRP):
Tester Connection Condition Specified Condition
a2-1 (CEI) - z9-1 (-) Ignition switch off 10 kΩ or higher



Post-procedure1

f.

Reconnect the high voltage cable connectors to the No. 1 Traction Battery Device Box Assembly.


g.

Install the HV battery upper cover panel.


Result:
Proceed to
OK
NG



OK

5.PERFORM INITIALIZATION (CURRENT SENSOR OFFSET LEARNING)

NG

REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

5.PERFORM INITIALIZATION (CURRENT SENSOR OFFSET LEARNING)

Pre-procedure1

a.

None.


Procedure1

b.

Turn the ignition switch to ON (READY).


c.

Perform a road test.

NOTICE:

Accelerate/decelerate gently. Avoid rapid acceleration/deceleration.



d.

Drive the vehicle with the value of Data List item "Hybrid/EV Battery Current" between -50 A to 50 A.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Current
50003 398 289
HINT:

Distance and driving time are not specified.



e.

Turn the ignition switch off and leave the vehicle for 30 seconds or more.


f.

Check that the value of "Hybrid/EV Battery Current" is between - 0.5 A and 0.5 A with the ignition switch to ON.

Powertrain > HV Battery > Data List
Tester Display
Hybrid/EV Battery Current
50003 398 289
NOTICE:
·

If the value is outside the specified range, perform the road test again.

·

This DTC may be output if Current Sensor Offset Learning has not been completed.



HINT:
·

If the ignition switch to ON and value of "Hybrid/EV Battery Current" is between - 0.5 A and 0.5 A, current sensor offset learning has been completed.

·

Even if the current sensor offset learning is not complete, the current sensor value will be corrected by repeating the road test a maximum of 7 times.




Post-procedure1

g.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

END