Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HV RELAY ASSEMBLY
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0424593 HV RELAY ASSEMBLY A

HYBRID / BATTERY CONTROL  HV RELAY ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery junction block assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of HV battery junction block assembly Current sensor offset learning DTCs are stored (Click here)

CAUTION:
·
A340386

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·
A340358

To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.



HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 6.INSTALL CONNECTOR COVER ASSEMBLY

Hide 73350C 8.DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY

Hide 9.REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 72693 10.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 71033 11.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Hide G92N1 12.REMOVE HV BATTERY UPPER COVER PANEL

Hide 821H1 13.DISCONNECT FLOOR UNDER WIRE

Hide G920NB 15.REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

Hide G3850 16.REMOVE NO.1 TRACTION BATTERY DEVICE BOX ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A464175

Disengage the claw and open the wiring harness protector.


b.

Disconnect the No. 1 traction battery device box assembly connector.

NOTICE:

Insulate the disconnected high-voltage connector with insulating tape.



c.

Disconnect the hybrid battery terminal block connector.

NOTICE:

Insulate the disconnected high-voltage connector with insulating tape.



d.

Remove the bolt and electric vehicle battery plug assembly from the HV battery.


e.
A464176

Disconnect the 2 No. 1 traction battery device box assembly connectors.

NOTICE:

Insulate the disconnected high-voltage connectors with insulating tape.



f.
A466647C01
1.615,2.146 1.906,2.302 true 1.948,2.229 2.26,2.427 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the wiring harness protector.


g.
A464177

Remove the 4 nuts and No. 1 traction battery device box assembly from the No. 1 hybrid battery shield sub-assembly.

NOTICE:

If the No. 1 traction battery device box assembly has been struck or dropped, replace it with a new one.