Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420051 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AA649  Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure  P1C7C49  Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure  P1C7D49  Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure  P1C7E49  Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure  P1C7F49  Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure  


DESCRIPTION

The hybrid vehicle control ECU monitors the battery ECU assembly and detects insulation malfunctions in the high-voltage system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AA649 Hybrid/EV Battery Voltage System Isolation Internal Electronic Failure Insulation resistance between the high-voltage circuit and the body has decreased.*1
(1 trip detection logic)
·

Inverter with converter assembly

·

HV floor under wire

·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Hybrid battery terminal block

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

Electric vehicle battery plug assembly

·

Hybrid vehicle transaxle assembly

·

Motor cable

·

Air conditioning system

·

Air conditioning wire


Does not come on Master Warning: Comes on
P1C7C49 Hybrid/EV Battery Voltage System Isolation (A/C Area) Internal Electronic Failure Insulation resistance of the compressor with motor assembly or air conditioning inverter has decreased.*2
(1 trip detection logic)
Air conditioning system Does not come on Master Warning: Comes on
P1C7D49 Hybrid/EV Battery Voltage System Isolation (Hybrid/EV Battery Area) Internal Electronic Failure Insulation resistance of the HV battery, battery ECU assembly or SMR has decreased.*2
(1 trip detection logic)
·

No. 1 traction battery device box assembly

·

Battery ECU assembly

·

Hybrid battery terminal block

·

No. 1 HV supply stack sub-assembly

·

No. 2 HV supply stack sub-assembly

·

Electric vehicle battery plug assembly


Does not come on Master Warning: Comes on
P1C7E49 Hybrid/EV Battery Voltage System Isolation (Transaxle Area) Internal Electronic Failure Insulation resistance of the hybrid vehicle transaxle assembly or inverter for the generator (MG1) and motor (MG2) has decreased.*2
(1 trip detection logic)
·

Hybrid vehicle transaxle assembly

·

Motor cable

·

Inverter with converter assembly


Does not come on Master Warning: Comes on
P1C7F49 Hybrid/EV Battery Voltage System Isolation (Direct Current Area) Internal Electronic Failure Insulation resistance of the inverter for the generator (MG1) and motor (MG2), A/C inverter, SMR or high-voltage direct current wire has decreased.*2
(1 trip detection logic)
·

Inverter with converter assembly

·

HV floor under wire

·

No. 1 traction battery device box assembly

·

Air conditioning system

·

Air conditioning wire


Does not come on Master Warning: Comes on

HINT:
·

*1: The insulation malfunction detection circuit in the battery ECU assembly monitors the insulation resistance between the high voltage circuits and body. If the insulation resistance decreases, the hybrid vehicle control ECU stores DTC P0AA649 and illuminates the master warning first regardless of malfunction area.

Depending on the vehicle condition, the high voltage circuit insulation resistance may return to normal. So if DTC P0AA649 outputs, complete the following steps as soon as possible.

·

*2: If the following operations are performed within the same trip after DTC P0AA649 is stored, just one of the related DTCs (P1C7C49, P1C7D49, P1C7E49 or P1C7F49) will be stored.

(a)

Apply the parking brake firmly.

NOTICE:

Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.


HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.


(b)

Wait for 1 minute or more with the vehicle stopped, the brake pedal firmly depressed, the ignition switch to ON (READY), shift lever in D and the air conditioning system on (Lo/MAX COOL, blower speed HI).

(c)

Turn the ignition switch off and wait for 2 minutes or more.

HINT:
·

DTCs and freeze frame data are useful information in determining the malfunctioning part. Before performing diagnosis, make sure to check and make a note of all output DTCs and freeze frame data. (Even if a high-voltage insulation malfunction cannot be reproduced, once stored, DTCs of insulation will not be cleared unless the clear operation is performed.)

·

When the insulation resistance of the HV battery area decreases and the ignition switch is turned to ON, DTC P1C7D49 is stored within 2 minutes.




·

When measuring insulation resistance using a megohmmeter, measure the resistance while jiggling the high voltage wire harness.



Related Data List (Reproduction of Phenomenon and Check)
DTC No. Data List
P0AA649
·

Short Wave Highest Value Level

·

Hybrid/EV Battery Voltage

·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Boost Ratio

·

A/C Consumption Power

·

SMRP Status

·

SMRB Status

·

SMRG Status

·

Generator Inverter Shutdown Status

·

Motor Inverter Shutdown Status

·

Insulation Resistance Division Check Completion using MG Inv

·

Insulation Resistance Division Check Completion using A/C Inv

·

Insulation Resistance Division Check Completion using SMR

·

Short Wave Highest Value Availability just after MG Inv On/Off

·

Short Wave Highest Value Availability just after A/C Inv On/Off

·

Short Wave Highest Value Availability just after SMR On/Off


P1C7C49
P1C7D49
P1C7E49
P1C7F49

Use the following items as a reference when duplicating the vehicle conditions at the time when the malfunction occurred.

Data List
·

Vehicle Speed

·

Engine Run Time

·

BATT Voltage

·

Distance from DTC Cleared

·

Ready Signal

·

Hybrid/EV Battery SOC


CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER REPLACING PARTS


HINT:

After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure. (Do not turn the ignition switch off during this inspection.)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Apply the parking brake and secure the wheels using chocks.

NOTICE:

Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.


HINT:

When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.


4.

When the vehicle is stationary, turn the ignition switch to ON (READY) with shift lever in P and wait for 1 minute or more.

5.

Turn the air conditioning system on (MAX COLD, blower speed HI).

6.

While depressing the brake pedal without depressing the accelerator pedal, move the shift lever to D and wait for 5 minutes.

- If step A is performed within the same trip after DTC P0AA649 is stored, the parts with insufficient insulation resistance will be determined and a DTC (P1C7C49, P1C7D49, P1C7E49 or P1C7F49) will be stored.

- If no DTCs are output, proceed to the next step.

7.

Drive the vehicle for approximately 5 minutes referring to the following freeze frame data items: "Vehicle Speed", "Shift Position", "Accelerator Position Sensor No.1 Voltage %", "Engine Speed", "Coolant Temperature", "Master Cylinder Control Torque", "Motor Temperature" and "Generator Temperature"

(If the freeze frame data item "Vehicle Speed" is 10 km/h (6 mph) or less, drive the vehicle at 10 km/h (6 mph) or more.)

- If step A is performed within the same trip after DTC P0AA649 is stored, the parts with insufficient insulation resistance will be determined and a DTC (P1C7C49, P1C7D49, P1C7E49 or P1C7F49) will be stored.

- If DTC P0AA649 is output, complete the Step A immediately as quickly as possible.

8.

Wait for 1 minute or more with the vehicle stopped, the ignition switch to ON (READY), shift lever in P and the air conditioning system on (Lo/COOL MAX, blower speed HI), then turn the ignition switch off and wait for 2 minutes or more. (Step A)

9.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.





WIRING DIAGRAM

A474383C03
0.927,1.052 1.24,1.208 0.313,0.156 10 false *1 1.656,2.896 1.969,3.052 0.313,0.156 10 false *2 2.563,1.792 2.875,1.948 0.313,0.156 10 false *3 2.563,3.896 2.875,4.052 0.313,0.156 10 false *4 2.563,4.521 2.875,4.677 0.313,0.156 10 false *5 1.948,4.927 2.26,5.083 0.313,0.156 10 false *6 0.438,3.667 0.75,3.823 0.313,0.156 10 false *7 3.625,1.052 3.938,1.208 0.313,0.156 10 false *8 4.427,2.073 4.74,2.229 0.313,0.156 10 false *9 5.24,3.031 5.708,3.188 0.469,0.156 10 false *10 6.198,2.698 6.667,2.854 0.469,0.156 10 false *11 6.188,3.573 6.656,3.729 0.469,0.156 10 false *12 4.104,5.323 4.573,5.479 0.469,0.156 10 false *13 4.333,6.125 4.802,6.281 0.469,0.156 10 false *14 5.74,6.115 6.208,6.271 0.469,0.156 10 false *15 0.146,0.24 0.458,0.396 0.313,0.156 10 false *a 3.417,7.49 3.729,7.646 0.313,0.156 10 false *b 5.625,7.104 5.938,7.26 0.313,0.156 10 false *c 1.281,6.365 1.594,6.521 0.313,0.156 10 false *d 6.083,4.615 6.396,4.771 0.313,0.156 10 false *e 3.635,7.125 3.948,7.281 0.313,0.156 10 false *f
*1 HV Battery *2 Battery ECU assembly
*3 SMRB *4 SMRG
*5 SMRP *6 System Main Resistor
*7 Service Plug Grip *8 Inverter with Converter Assembly
*9 Boost Converter *10 Inverter
*11 Generator (MG1) *12 Motor (MG2)
*13 Compressor with Motor Assembly *14 A/C Inverter
*15 A/C Motor - -
*a High-voltage Areas *b DTC P0AA649 Vehicle Insulation Resistance Reduction Area
*c DTC P1C7C49 Air Conditioning System Area *d DTC P1C7D49 HV Battery Area
*e DTC P1C7E49 Hybrid Vehicle Transaxle Assembly Area *f DTC P1C7F49 High Voltage Direct Current Area


A460765E02
0.167,3.396 0.948,3.948 0.781,0.552 10 false Service Plug Grip 0.104,2.688 1.042,3.094 0.938,0.406 10 false Hybrid Battery Terminal Block 0.104,0.906 1.146,1.521 1.042,0.615 10 false No. 2 HV Supply Stack Sub-assembly 0.083,1.844 1.125,2.458 1.042,0.615 10 false No. 1 HV Supply Stack Sub-assembly 1.271,2.458 1.729,2.656 0.458,0.198 10 false z14 1.302,3.146 1.76,3.344 0.458,0.198 10 false z8 1.323,1.531 1.479,1.729 0.156,0.198 10 false A 1.958,0.563 2.271,0.823 0.313,0.26 10 false z10 1.99,1.385 2.448,1.583 0.458,0.198 10 false z9 2.021,0.365 2.177,0.563 0.156,0.198 10 false 1 2.021,1.198 2.177,1.396 0.156,0.198 10 false 1 1.104,2.448 1.26,2.646 0.156,0.198 10 false 1 1.094,3.167 1.25,3.365 0.156,0.198 10 false 1 1.115,3.469 1.271,3.667 0.156,0.198 10 false 1 3.25,0.917 3.865,1.115 0.615,0.198 10 false SMRB 3.396,1.75 4.01,1.948 0.615,0.198 10 false SMRG 3.417,2.583 4.031,2.781 0.615,0.198 10 false SMRP 2.229,3.063 5.083,3.26 2.854,0.198 10 false No. 1 Traction Battery Device Box Assembly 4.698,0.438 5.156,0.635 0.458,0.198 10 false CBI 4.708,1.25 5.167,1.448 0.458,0.198 10 false CEI 5.094,0.552 5.406,0.75 0.313,0.198 10 false a1 5.135,0.365 5.292,0.563 0.156,0.198 10 false 1 5.104,1.385 5.417,1.583 0.313,0.198 10 false a2 5.135,1.188 5.292,1.385 0.156,0.198 10 false 1 0.063,5.635 0.375,5.833 0.313,0.198 10 false k1 0.052,5.813 2.24,6.219 2.188,0.406 10 false Hybrid Vehicle Transaxle Assembly (Motor (MG2)) 0.063,7.615 0.375,7.813 0.313,0.198 10 false k1 0.052,7.792 2.26,8.188 2.208,0.396 10 false Hybrid Vehicle Transaxle Assembly (Generator (MG1)) 1.635,4.729 1.792,4.927 0.156,0.198 10 false U 1.635,5.063 1.792,5.26 0.156,0.198 10 false V 1.604,5.396 1.76,5.594 0.156,0.198 10 false W 3.375,4.719 3.531,4.917 0.156,0.198 10 false U 3.375,5.094 3.531,5.292 0.156,0.198 10 false V 3.365,5.438 3.521,5.635 0.156,0.198 10 false W 1.865,4.563 2.021,4.76 0.156,0.198 10 false 2 1.854,4.917 2.01,5.115 0.156,0.198 10 false 3 1.844,5.271 2,5.469 0.156,0.198 10 false 1 3.135,4.5 3.292,4.698 0.156,0.198 10 false 2 3.125,4.906 3.281,5.104 0.156,0.198 10 false 3 3.115,5.25 3.271,5.448 0.156,0.198 10 false 1 3.094,4.708 3.406,4.906 0.313,0.198 10 false k2 3.083,5.073 3.396,5.271 0.313,0.198 10 false k2 3.094,5.427 3.406,5.625 0.313,0.198 10 false k2 3.083,6.677 3.396,6.875 0.313,0.198 10 false k2 3.094,7.042 3.406,7.24 0.313,0.198 10 false k2 3.094,7.396 3.406,7.594 0.313,0.198 10 false k2 3.115,6.49 3.271,6.688 0.156,0.198 10 false 5 3.125,6.875 3.281,7.073 0.156,0.198 10 false 6 3.125,7.229 3.281,7.427 0.156,0.198 10 false 4 1.635,6.698 1.792,6.896 0.156,0.198 10 false U 1.635,7.052 1.792,7.25 0.156,0.198 10 false V 1.604,7.385 1.76,7.583 0.156,0.198 10 false W 3.375,6.698 3.531,6.896 0.156,0.198 10 false U 3.375,7.063 3.531,7.26 0.156,0.198 10 false V 3.375,7.406 3.531,7.604 0.156,0.198 10 false W 1.833,6.531 1.99,6.729 0.156,0.198 10 false 5 1.833,6.875 1.99,7.073 0.156,0.198 10 false 6 1.844,7.229 2,7.427 0.156,0.198 10 false 4 2.99,8.177 5.094,8.573 2.104,0.396 10 false Inverter with Converter Assembly 4.51,4.792 4.969,4.99 0.458,0.198 10 false CEI 4.51,5.344 4.969,5.542 0.458,0.198 10 false CBI 4.865,4.792 5.177,4.99 0.313,0.198 10 false a3 4.875,5.333 5.188,5.531 0.313,0.198 10 false a3 4.906,4.594 5.063,4.792 0.156,0.198 10 false 2 4.906,5.125 5.063,5.323 0.156,0.198 10 false 1 4.354,6.74 4.969,6.938 0.615,0.198 10 false ACPB 4.375,7.281 4.99,7.479 0.615,0.198 10 false ACPE 4.875,6.76 5.188,6.958 0.313,0.198 10 false b2 4.885,7.302 5.198,7.5 0.313,0.198 10 false b2 4.906,6.563 5.063,6.76 0.156,0.198 10 false 1 4.917,7.094 5.073,7.292 0.156,0.198 10 false 2 5.281,6.615 5.438,6.813 0.156,0.198 10 false 2 5.271,7.135 5.427,7.333 0.156,0.198 10 false 1 5.458,6.771 5.771,6.969 0.313,0.198 10 false PB 5.469,7.302 5.781,7.5 0.313,0.198 10 false PE 5.417,7.583 5.729,7.781 0.313,0.198 10 false b1 5.396,7.75 6.833,8.333 1.438,0.583 10 false Compressor with Motor Assembly 1.208,8.531 4.115,8.729 2.906,0.198 10 false : High Voltage Line 2.292,0.417 2.604,0.677 0.313,0.26 10 false + 2.292,1.24 2.604,1.5 0.313,0.26 10 false - 1.083,1.521 1.24,1.719 0.156,0.198 10 false 1 1.125,3.833 1.281,4.031 0.156,0.198 10 false 2

SYSTEM DESCRIPTION

HINT:

If a decrease in insulation resistance cannot be confirmed using a megohmmeter, check "Short Wave Highest Value Level" in the Data List.


SHORT WAVE HIGHEST VALUE LEVEL


a.

"Short Wave Highest Value Level" shows a decrease in insulation resistance. When insulation resistance decreases, "Insulation Lower" will be displayed. However, even though the insulation resistance of the vehicle is normal, "Short Wave Highest Value Level" may decrease, so that "Not Judge" will be displayed for any of the following conditions.

·

Within approximately 1 minute since the ignition switch was turned to ON.

·

When the system voltages ("Hybrid/EV Battery Voltage", "VL-Voltage before Boosting" and "VH-Voltage after Boosting") are changing.

·

During boosting. If the Data List item "Boost Ratio" is not 0% or within a few seconds of it becoming 0%. (The values of "Hybrid/EV Battery Voltage", "VL-Voltage before Boosting" and "VH-Voltage after Boosting" are about the same when not boosting.)

·

When "No" is displayed for any of the following Data List items:

- Short Wave Highest Value Availability just after MG Inv On/Off

- Short Wave Highest Value Availability just after A/C Inv On/Off

- Short Wave Highest Value Availability just after SMR On/Off



b.

When "Short Wave Highest Value Level" shows "Insulation Lower LV3", insulation resistance will be close to 0 Ω. In this case, damage to a high-voltage cable or hybrid component (high-voltage), or a short to body ground due to intrusion of foreign matter, such as metal particles, can be suspected.



RELATED FREEZE FRAME DATA


If problem symptoms cannot be reproduced and a malfunction still exists after replacing a part as instructed, checking the following freeze frame data can help determine a trouble area.


Items to be Checked Using Freeze Frame Data:
Freeze Frame Data Diagnostic Note
Short Wave Highest Value Level Indicates that the insulation resistance has decreased.
·

VL-Voltage before Boosting

·

VH-Voltage after Boosting

·

Hybrid/EV Battery Voltage

·

Boost Ratio


During boosting (when "Boost Ratio" is not 0%), or when "VL-Voltage before Boosting", "VH-Voltage after Boosting" or "Hybrid/EV Battery Voltage" is varying, "Short Wave Highest Value Level" may decrease even though the insulation resistance is normal.
·

SMRP Status

·

SMRB Status

·

SMRG Status


When "SMRP Status", "SMRB Status" and "SMRG Status" are all OFF, the insulation malfunction detection circuit detects a decrease in insulation resistance in the HV battery area ((*d) in the wiring diagram).
Example:

When the ignition switch is turned to ON (not ON (READY)), all 3 system main relays are off and it is suspected that the HV battery assembly is disconnected from the high voltage circuits. If "Short Wave Highest Value Level" decreases a few minutes after the ignition switch is turned to ON (not ON (READY)), the HV battery assembly may have an insulation malfunction.


Motor Inverter Shutdown Status When "Motor Inverter Shutdown Status" is ON, the insulation malfunction detection circuit cannot detect a decrease in insulation resistance in the motor system AC (alternating current) section (motor (MG2) side of (*e) in the wiring diagram).
The motor system AC (alternating current) section includes the motor (MG2) in the hybrid vehicle transaxle assembly, motor cables and the AC (alternating current) section of the motor drive circuit in the inverter with converter assembly.
Generator Inverter Shutdown Status When "Generator Inverter Shutdown Status" is ON, the insulation malfunction detection circuit cannot detect a decrease in insulation resistance in the generator system AC (alternating current) section (generator (MG1) side of (*e) in the wiring diagram).
The generator system AC (alternating current) section includes the generator (MG1) in the hybrid vehicle transaxle assembly, generator cables and the AC (alternating current) section of the generator drive circuit in the inverter with converter assembly.
A/C Consumption Power The compressor with motor assembly AC (alternating current) section ((*c) in the wiring diagram) includes the air conditioning motor, wiring between the air conditioning motor and air conditioning inverter, and the AC (alternating current) section of the air conditioning motor drive circuit in the air conditioning inverter.
With the vehicle stopped, turn on/off the air conditioning system and observe "Short Wave Highest Value Level" to use as a diagnosis reference.

HINT:
·

Reproducing the vehicle conditions the moment a DTC was stored according to the freeze frame data and results of the customer problem analysis helps ensure that the same DTC is stored again.

Driving Status
Item Diagnostic Note
Vehicle Speed -
Accelerator Position Sensor No.1 Voltage % -
Engine Speed -
Shift Position -
Master Cylinder Control Torque -
Coolant Temperature -

Operation Conditions
Item Diagnostic Note
Motor Temperature If any liquid leaks into the ATF, insulation resistance may decrease only when the temperature is high.
The motor temperature is likely to increase if the motor speed is low and output torque is high such as when cruising uphill slowly or accelerating from a low speed.
Generator Temperature If any liquid leaks into the ATF, insulation resistance may decrease only when the temperature is high.
The generator temperature is likely to increase under repeat acceleration and deceleration while the vehicle is driven in the mid speed range (60 to 80 km/h (37 to 50 mph)).

·

Customer Problem Analysis

Ask the customer about the operating conditions and environment when the malfunction occurred.

Item Diagnostic Note
Driving Condition (acceleration, deceleration, turning, etc.) Changes in the insulation of the parts with insufficient insulation due to changes in G force or vibration is suspected.
Road Condition (unpaved, etc.)
Weather (rain, snow, etc.) Water intrusion is suspected
Washing the vehicle (Whether the malfunction occurred after washing the vehicle?)




CAUTION / NOTICE / HINT

CAUTION:
·
A361801

When troubleshooting DTC P0AA649, use either a tool wrapped with vinyl insulation tape or an insulated tool. (It is extremely dangerous when a high-voltage charge passes through a non-insulated tool causing a short.)


·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery



·
A357588


·

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.


·
A358042


·

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.


·
A357589C58
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.



·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.


·
A358021C06
0.604,4.135 0.917,4.333 0.313,0.198 10 false *a 2.719,4.135 3.031,4.333 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

When measuring insulation resistance using a megohmmeter, set the megohmmeter to 500 V.


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL, HV BATTERY)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
Powertrain > HV Battery > Trouble Codes
50001 398
Result:
Result Proceed to
P0AA649, P1C7C49, P1C7D49, P1C7E49 or P1C7F49 is output and Microcomputer malfunction of Hybrid control system DTCs in the table below are output A
P0AA649, P1C7C49, P1C7D49, P1C7E49 or P1C7F49 is output and Microcomputer malfunction of Hybrid battery system DTCs in the table below are output B
P0AA649, P1C7C49, P1C7D49, P1C7E49 or P1C7F49 is output and Power source circuit malfunction of Hybrid control system DTCs in the table below are output C
P0AA649, P1C7C49, P1C7D49, P1C7E49 or P1C7F49 is output and System malfunction of Hybrid control system DTCs in the table below are output D
P0AA649, P1C7C49, P1C7D49, P1C7E49 or P1C7F49 is output and DTCs other than the DTCs in the table below are output E
Only P0AA649, P1C7C49, P1C7D49, P1C7E49 or P1C7F49 is output F


Malfunction Content System Relevant DTC
Microcomputer malfunction Hybrid control system P060647 Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure
P060A29 Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid
P060A44 Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure
P060A45 Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure
P060A49 Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure
P060B1C Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range
P060B71 Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck
P1CE31C Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range
P1CE349 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure
P1CE371 Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck
Hybrid battery system P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060A87 Hybrid/EV Battery Energy Control Module Processor from Monitoring Processor Missing Message
P060B49 Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure
Power Source Circuit Malfunction Hybrid control system P06881F ECM/PCM Power Relay Sense Circuit Intermittent
System malfunction Hybrid control system P1C9E9F Hybrid/EV System Reset Stuck Off

HINT:
·

P0AA649, P1C7C49, P1C7D49, P1C7E49 or P1C7F49 may be output as a result of the malfunction indicated by the DTCs above.

(a)

The chart above is listed in inspection order of priority.

(b)

Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)





Post-procedure1

c.

Turn the ignition switch off.



A

B

C

D

E

2.CHECK DTC OUTPUT (HYBRID CONTROL)

F

2.CHECK DTC OUTPUT (HYBRID CONTROL)
2.CHECK DTC OUTPUT (HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397
NOTICE:
·

DTC P1C7C49, P1C7D49, P1C7E49 and P1C7F49 are not stored with P0AA649 at the same time. If a drop in insulation resistance is detected and DTC P0AA649 is output, wait for 1 minute with the ignition switch to ON (READY), the shift lever in D and the air conditioning system on within the same trip, then turn the ignition switch off and wait for 2 minutes to determine the DTC (P1C7C49, P1C7D49, P1C7E49 or P1C7F49).

·

If only DTC P0AA649 is output, perform the diagnostic procedure for DTC P0AA649 to inspect all of the high voltage circuits.

·

When any other DTC indicating parts which the insulation resistance dropped are output, perform the diagnostic procedure for each DTC.



Result:
Result Proceed to
P0AA649 and P1C7C49 are output A
P0AA649 and P1C7D49 are output B
P0AA649 and P1C7E49 are output C
P0AA649 and P1C7F49 are output D
Only P0AA649 is output E



Post-procedure1

c.

Turn the ignition switch off.



A

3.GO TO AIR CONDITIONING SYSTEM (P1C7C49)

B

4.CHECK HV BATTERY (HIGH VOLTAGE CABLE)

C

16.CHECK INVERTER WITH CONVERTER ASSEMBLY

D

21.CHECK HIGH VOLTAGE DIRECT CURRENT AREA

E

30.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2))
3.GO TO AIR CONDITIONING SYSTEM (P1C7C49)

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

4.CHECK HV BATTERY (HIGH VOLTAGE CABLE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


HINT:

Make sure that no foreign matter or water has entered the HV battery.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



c.
A459833

Disconnect the battery ECU assembly connectors.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

d.
A458493C01
1.552,1.188 1.313,1.531 true 1.938,1.188 2.25,1.542 true 0.083,0.073 0.396,0.229 0.313,0.156 10 true *a 1.219,1.552 1.417,1.729 0.198,0.177 10 true 1 2.292,1.552 2.49,1.729 0.198,0.177 10 true 2
*a Service Plug Grip Removed
(Service Plug Grip Connecting Terminals)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground Ignition switch off 10 MΩ or higher
2 - Body ground Ignition switch off 10 MΩ or higher



Post-procedure1

e.

None.


Result:
Proceed to
OK
NG



OK

5.REPLACE BATTERY ECU ASSEMBLY

NG

6.CHECK ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY
5.REPLACE BATTERY ECU ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

6.CHECK ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A458508N01
0.344,1.177 0.677,1.417 0.333,0.24 1.677,0.719 2.042,0.958 0.365,0.24 0.417,1.208 0.604,1.385 0.188,0.177 10 true z8 1.75,0.75 1.969,0.927 0.219,0.177 10 true z9

Disconnect the electric vehicle battery plug assembly connectors.


Procedure1

c.
A458493C01
1.552,1.188 1.313,1.531 true 1.938,1.188 2.25,1.542 true 0.083,0.073 0.396,0.229 0.313,0.156 10 true *a 1.219,1.552 1.417,1.729 0.198,0.177 10 true 1 2.292,1.552 2.49,1.729 0.198,0.177 10 true 2
*a Service Plug Grip Removed
(Service Plug Grip Connecting Terminals)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground Ignition switch off 10 MΩ or higher
2 - Body ground Ignition switch off 10 MΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

7.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

12.REPLACE ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY
7.CHECK NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the electric vehicle battery plug assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY PLUG>REMOVAL



c.
A458512N01
1.906,1.635 2.292,1.854 0.385,0.219 1.979,1.677 2.25,1.833 0.271,0.156 10 true z10

Disconnect the high voltage cable connector of the HV battery from the No. 1 traction battery device box assembly.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

d.
A460002C01
0.604,1.719 0.969,1.979 0.365,0.26 1.833,0.396 2.198,0.667 0.365,0.271 1.24,1.729 1.333,1.5 true 2.26,0.844 2.438,0.438 true 0.042,0.063 0.354,0.219 0.313,0.156 10 true *a 1.385,1.385 1.583,1.552 0.198,0.167 10 true + 2.521,0.354 2.708,0.521 0.188,0.167 10 true - 0.677,1.771 0.948,1.948 0.271,0.177 10 true z10 1.927,0.458 2.125,0.615 0.198,0.156 10 true z9
*a Component without harness connected
(No. 1 Traction Battery Device Box Assembly)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
z10-1 (+) - Body ground Ignition switch off 10 MΩ or higher
z9-1 (-) - Body ground Ignition switch off 10 MΩ or higher



Post-procedure1

e.

None.


Result:
Proceed to
OK
NG



OK

8.CHECK HYBRID BATTERY TERMINAL BLOCK

NG

28.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY
8.CHECK HYBRID BATTERY TERMINAL BLOCK
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A460003N01
1.094,0.521 1.469,0.771 0.375,0.25 1.146,0.563 1.427,0.75 0.281,0.188 10 true z14

Disconnect the high voltage cable connector of the HV battery from the hybrid battery terminal block.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

c.
A458510C01
0.906,0.938 1.26,1.167 0.354,0.229 1.479,0.458 1.833,0.688 0.354,0.229 0.052,0.052 0.271,0.219 0.219,0.167 10 true *a 1.021,0.979 1.208,1.135 0.188,0.156 10 true z8 1.542,0.5 1.813,0.667 0.271,0.167 10 true z14
*a Component without harness connected
(Hybrid Battery Terminal Block)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
z8-1 - Body ground Ignition switch off 10 MΩ or higher
z14-1 - Body ground Ignition switch off 10 MΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

9.CHECK HV BATTERY

NG

13.REPLACE HYBRID BATTERY TERMINAL BLOCK
9.CHECK HV BATTERY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that no electrolyte is leaking from each HV supply stack sub-assembly.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>INSPECTION



Result:
Result Proceed to
Electrolyte is not leaking from the HV supply stack sub-assembly. A
Electrolyte is leaking from the HV supply stack sub-assembly. B



A

10.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

B

14.REPLACE HV BATTERY (HV SUPPLY STACK SUB-ASSEMBLY THAT HAS A LEAK OF ELECTROLYTE)
10.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A458495N03
0.906,1.01 1.25,1.26 0.344,0.25 1.042,1.063 1.188,1.229 0.146,0.167 10 true A

Disconnect the HV battery high voltage connector.

NOTICE:

Insulate each disconnected high-voltage connector with insulating tape. Wrap the connector from the wire harness side to the end of the connector.



Procedure1

c.
A376562C03
0.458,0.958 0.698,1.177 0.24,0.219 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 0.531,0.99 0.771,1.292 0.24,0.302 10 false A
*a Component without harness connected
(No. 2 HV Supply Stack Sub-assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
A-1 - Body ground Ignition switch off 10 MΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

11.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NG

15.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY
11.REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

12.REPLACE ELECTRIC VEHICLE BATTERY PLUG ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

13.REPLACE HYBRID BATTERY TERMINAL BLOCK

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

14.REPLACE HV BATTERY (HV SUPPLY STACK SUB-ASSEMBLY THAT HAS A LEAK OF ELECTROLYTE)

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

15.REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

16.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A458488

Disconnect the motor cable from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water enters the inverter with converter assembly.



Procedure1

c.
A460004C01
1.813,0.938 1.698,0.938 1.698,0.938 1.469,1.229 true 1.865,0.885 2.115,1.063 0.25,0.177 10 true *a
*a High Voltage Terminal


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
High voltage terminal - Body ground Ignition switch off 1 MΩ or higher


HINT:

Perform this inspection with the motor cable disconnected from the inverter with converter assembly.



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

17.CHECK MOTOR CABLE (FOR MG2)

NG

23.REPLACE INVERTER WITH CONVERTER ASSEMBLY
17.CHECK MOTOR CABLE (FOR MG2)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the motor cable from the hybrid vehicle transaxle assembly.

HINT:

Click hereDrivetrain>P910 (HYBRID TRANSMISSION / TRANSAXLE)>MOTOR CABLE>REMOVAL



Procedure1

c.
A377530C54
1.51,0.188 1.927,0.448 0.417,0.26 2.729,1.542 2.938,1.792 false 0.99,1.063 0.813,1.854 true 1.406,1.042 1.406,1.865 true 1.688,1.031 1.938,1.885 true 3.01,1.75 3.219,1.927 0.208,0.177 10 false *1 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.646,0.25 1.958,0.448 0.313,0.198 10 false k2 0.75,1.906 1.063,2.104 0.313,0.198 10 false W 1.375,1.917 1.615,2.125 0.24,0.208 10 false U 1.927,1.917 2.167,2.125 0.24,0.208 10 false V
*1 Shield Ground
*a Motor Cable (for MG2)
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
k2-2 (U) - Shield ground Ignition switch off 10 MΩ or higher
k2-3 (V) - Shield ground Ignition switch off 10 MΩ or higher
k2-1 (W) - Shield ground Ignition switch off 10 MΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

18.CHECK MOTOR CABLE (FOR MG1)

NG

20.REPLACE MOTOR CABLE
18.CHECK MOTOR CABLE (FOR MG1)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the motor cable from the hybrid vehicle transaxle assembly.

HINT:

Click hereDrivetrain>P910 (HYBRID TRANSMISSION / TRANSAXLE)>MOTOR CABLE>REMOVAL



Procedure1

c.
A377530C56
1.573,0.198 1.948,0.427 0.375,0.229 2.177,1.042 2.177,1.885 true 2.448,1.063 2.708,1.875 true 1.917,1.052 1.615,1.885 true 2.75,1.531 2.99,1.76 false 3.031,1.719 3.344,1.917 0.313,0.198 10 false *1 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 2.146,1.917 2.458,2.115 0.313,0.198 10 false U 2.698,1.917 3.01,2.115 0.313,0.198 10 false V 1.563,1.917 1.875,2.115 0.313,0.198 10 false W 1.698,0.25 2.01,0.448 0.313,0.198 10 false k2
*1 Shield Ground
*a Motor Cable (for MG1)
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
k2-5 (U) - Shield ground Ignition switch off 10 MΩ or higher
k2-6 (V) - Shield ground Ignition switch off 10 MΩ or higher
k2-4 (W) - Shield ground Ignition switch off 10 MΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

19.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

20.REPLACE MOTOR CABLE
19.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

20.REPLACE MOTOR CABLE

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

21.CHECK HIGH VOLTAGE DIRECT CURRENT AREA
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A460005

Disconnect the HV floor under wire connector from the inverter with converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the HV floor under wire.



Procedure1

c.
A365608C68
0.635,0.479 1.094,0.76 0.458,0.281 0.885,0.177 1.25,0.177 false 1.052,1.083 1.635,0.688 true 2.667,1.104 1.979,0.688 true 0.698,0.104 1.01,0.26 0.313,0.156 10 false *1 0.083,0.042 0.396,0.198 0.313,0.156 10 false *a 0.771,0.99 1.083,1.146 0.313,0.156 10 false CBI 2.74,1.031 3.052,1.188 0.313,0.156 10 false CEI 0.802,0.542 1.115,0.698 0.313,0.156 10 false a3
*1 Shield Ground
*a HV Floor Under Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure not to damage or deform the terminal being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition
a3-1 (CBI) - Body ground and shield ground Ignition switch off 10 MΩ or higher
a3-2 (CEI) - Body ground and shield ground Ignition switch off 10 MΩ or higher


HINT:

Visually inspect the HV floor under wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

22.CHECK AIR CONDITIONING WIRE

NG

27.CHECK FLOOR UNDER WIRE
22.CHECK AIR CONDITIONING WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A460065

Disconnect the air conditioning wire connector from the inverter with converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the air conditioning wire.



Procedure1

c.
A380308C53
0.365,0.5 0.792,0.76 0.427,0.26 1.427,0.688 0.667,1.24 true 1.677,0.688 2.406,1.323 true 2.729,0.563 2.49,0.906 2.49,0.906 3.01,0.656 true 1,0.167 0.656,0.167 false 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 2.354,0.906 2.667,1.063 0.313,0.156 10 true *b 0.521,0.563 0.833,0.719 0.313,0.156 10 false b2 0.51,1.281 0.927,1.469 0.417,0.188 10 false ACPE 2.292,1.354 2.708,1.542 0.417,0.188 10 false ACPB 0.49,0.104 0.906,0.292 0.417,0.188 10 false *1
*1 Shield Ground
*a Air Conditioning Wire
(Inverter with Converter Assembly Side)
*b Tip of Terminal


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure to inspect with connecting the tester probes to the tips of the terminal.



Standard Resistance:
Tester Connection Condition Specified Condition
b2-1 (ACPB) - Body ground and shield ground Ignition switch off 3 MΩ or higher
b2-2 (ACPE) - Body ground and shield ground Ignition switch off 3 MΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

23.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

24.CHECK AIR CONDITIONING WIRE
23.REPLACE INVERTER WITH CONVERTER ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

24.CHECK AIR CONDITIONING WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A458496N01
1.229,0.563 1.594,0.823 0.365,0.26 1.344,0.615 1.552,0.792 0.208,0.177 10 true b1

Disconnect the b1 air conditioning wire from the compressor with motor assembly.

HINT:

Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for M15A-FXE)>REMOVAL



Procedure1

c.
A380308C53
0.365,0.5 0.792,0.76 0.427,0.26 1.427,0.688 0.667,1.24 true 1.677,0.688 2.406,1.323 true 2.729,0.563 2.49,0.906 2.49,0.906 3.01,0.656 true 1,0.167 0.656,0.167 false 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 2.354,0.906 2.667,1.063 0.313,0.156 10 true *b 0.521,0.563 0.833,0.719 0.313,0.156 10 false b2 0.51,1.281 0.927,1.469 0.417,0.188 10 false ACPE 2.292,1.354 2.708,1.542 0.417,0.188 10 false ACPB 0.49,0.104 0.906,0.292 0.417,0.188 10 false *1
*1 Shield Ground
*a Air Conditioning Wire
(Inverter with Converter Assembly Side)
*b Tip of Terminal


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure to inspect with connecting the tester probes to the tips of the terminal.



Standard Resistance:
Tester Connection Condition Specified Condition
b2-1 (ACPB) - Body ground and shield ground Ignition switch off 10 MΩ or higher
b2-2 (ACPE) - Body ground and shield ground Ignition switch off 10 MΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

25.GO TO AIR CONDITIONING SYSTEM (P1C7C49)

NG

26.REPLACE AIR CONDITIONING WIRE
25.GO TO AIR CONDITIONING SYSTEM (P1C7C49)

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

26.REPLACE AIR CONDITIONING WIRE
Result:
Proceed to
NEXT



NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

27.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the HV battery upper cover panel.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL



c.
A458497N05
1.719,1.74 2.135,2 0.417,0.26 2.125,1.396 2.542,1.656 0.417,0.26 1.771,1.802 2.042,1.969 0.271,0.167 10 true a1 2.177,1.448 2.438,1.625 0.26,0.177 10 true a2

Disconnect the HV floor under wire connectors from the No. 1 traction battery device box assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the HV floor under wire.



Procedure1

d.
A365608C68
0.635,0.479 1.094,0.76 0.458,0.281 0.885,0.177 1.25,0.177 false 1.052,1.083 1.635,0.688 true 2.667,1.104 1.979,0.688 true 0.698,0.104 1.01,0.26 0.313,0.156 10 false *1 0.083,0.042 0.396,0.198 0.313,0.156 10 false *a 0.771,0.99 1.083,1.146 0.313,0.156 10 false CBI 2.74,1.031 3.052,1.188 0.313,0.156 10 false CEI 0.802,0.542 1.115,0.698 0.313,0.156 10 false a3
*1 Shield Ground
*a HV Floor Under Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure not to damage or deform the terminal being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition
a1-1 (CBI) - Body ground and shield ground Ignition switch off 10 MΩ or higher
a1-2 (CEI) - Body ground and shield ground Ignition switch off 10 MΩ or higher


HINT:

Visually inspect the HV floor under wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.



Post-procedure1

e.

None.


Result:
Proceed to
OK
NG



OK

28.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NG

29.REPLACE FLOOR UNDER WIRE
28.REPLACE NO. 1 TRACTION BATTERY DEVICE BOX ASSEMBLY

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

29.REPLACE FLOOR UNDER WIRE

NEXT

PERFORM CONFIRMATION AFTER REPLACING PARTS

30.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG2))
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A458488

Disconnect the motor cable from the inverter with converter assembly.

HINT:

Make sure that no foreign matter, coolant or water enters the inverter with converter assembly.



c.

Connect the cable to the negative (-) auxiliary battery terminal.

HINT:

As the insulation resistance may vary when motor (MG2) rotates, perform this inspection while rotating the front wheels.



d.

Turn the ignition switch to ON.

NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Move the shift lever to N and lift the vehicle.


f.

Turn the ignition switch off.


Procedure1

g.
A377530C54
1.51,0.188 1.927,0.448 0.417,0.26 2.729,1.542 2.938,1.792 false 0.99,1.063 0.813,1.854 true 1.406,1.042 1.406,1.865 true 1.688,1.031 1.938,1.885 true 3.01,1.75 3.219,1.927 0.208,0.177 10 false *1 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.646,0.25 1.958,0.448 0.313,0.198 10 false k2 0.75,1.906 1.063,2.104 0.313,0.198 10 false W 1.375,1.917 1.615,2.125 0.24,0.208 10 false U 1.927,1.917 2.167,2.125 0.24,0.208 10 false V
*1 Shield Ground
*a Motor Cable (for MG2)
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below while rotating the front wheels 2 revolutions in the same direction simultaneously.

NOTICE:
·

Carefully perform this inspection as the motor (MG2) may generate current when the front wheels are rotated by hand.

·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition
k2-2 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher
k2-3 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
k2-1 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher



Post-procedure1

h.

Lower the vehicle and move the shift lever to P.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

31.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1))

NG

35.CHECK MOTOR CABLE (FOR MG2)
31.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE (FOR MG1))
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Connect the cable to the negative (-) auxiliary battery terminal.

HINT:

As the insulation resistance may vary when generator (MG1) rotates, perform this inspection while rotating the front wheels.



c.

Turn the ignition switch to ON.

NOTICE:

Turning the ignition switch to ON with the service plug grip removed causes DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Move the shift lever to N and lift the vehicle.


e.

Turn the ignition switch off.


Procedure1

f.
A377530C56
1.573,0.198 1.948,0.427 0.375,0.229 2.177,1.042 2.177,1.885 true 2.448,1.063 2.708,1.875 true 1.917,1.052 1.615,1.885 true 2.75,1.531 2.99,1.76 false 3.031,1.719 3.344,1.917 0.313,0.198 10 false *1 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 2.146,1.917 2.458,2.115 0.313,0.198 10 false U 2.698,1.917 3.01,2.115 0.313,0.198 10 false V 1.563,1.917 1.875,2.115 0.313,0.198 10 false W 1.698,0.25 2.01,0.448 0.313,0.198 10 false k2
*1 Shield Ground
*a Motor Cable (for MG1)
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below while rotating the front wheels 2 revolutions in the same direction simultaneously.

NOTICE:
·

Carefully perform this inspection as the generator (MG1) may generate current when the front wheels are rotated by hand.

·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition
k2-5 (U) - Body ground and shield ground Ignition switch off 10 MΩ or higher
k2-6 (V) - Body ground and shield ground Ignition switch off 10 MΩ or higher
k2-4 (W) - Body ground and shield ground Ignition switch off 10 MΩ or higher



Post-procedure1

g.

Lower the vehicle and move the shift lever to P.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

32.CHECK AIR CONDITIONING WIRE

NG

36.CHECK MOTOR CABLE (FOR MG1)
32.CHECK AIR CONDITIONING WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A458489

Disconnect the air conditioning wire connector from the inverter with converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the air conditioning wire.



Procedure1

c.
A380308C53
0.365,0.5 0.792,0.76 0.427,0.26 1.427,0.688 0.667,1.24 true 1.677,0.688 2.406,1.323 true 2.729,0.563 2.49,0.906 2.49,0.906 3.01,0.656 true 1,0.167 0.656,0.167 false 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 2.354,0.906 2.667,1.063 0.313,0.156 10 true *b 0.521,0.563 0.833,0.719 0.313,0.156 10 false b2 0.51,1.281 0.927,1.469 0.417,0.188 10 false ACPE 2.292,1.354 2.708,1.542 0.417,0.188 10 false ACPB 0.49,0.104 0.906,0.292 0.417,0.188 10 false *1
*1 Shield Ground
*a Air conditioning wire
(Inverter with Converter Assembly Side)
*b Tip of Terminal


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure to inspect with connecting the tester probes to the tips of the terminal.



Standard Resistance:
Tester Connection Condition Specified Condition
b2-1 (ACPB) - Body ground and shield ground Ignition switch off 3 MΩ or higher
b2-2 (ACPE) - Body ground and shield ground Ignition switch off 3 MΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

33.CHECK FLOOR UNDER WIRE

NG

24.CHECK AIR CONDITIONING WIRE
33.CHECK FLOOR UNDER WIRE
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A376123

Disconnect the HV floor under wire connector from the inverter with converter assembly.

HINT:

Make sure that no foreign matter has entered or contaminated the HV floor under wire.



Procedure1

c.
A365608C68
0.635,0.479 1.094,0.76 0.458,0.281 0.885,0.177 1.25,0.177 false 1.052,1.083 1.635,0.688 true 2.667,1.104 1.979,0.688 true 0.698,0.104 1.01,0.26 0.313,0.156 10 false *1 0.083,0.042 0.396,0.198 0.313,0.156 10 false *a 0.771,0.99 1.083,1.146 0.313,0.156 10 false CBI 2.74,1.031 3.052,1.188 0.313,0.156 10 false CEI 0.802,0.542 1.115,0.698 0.313,0.156 10 false a3
*1 Shield Ground
*a HV Floor Under Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:
·

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.

·

Be sure not to damage or deform the terminal being inspected.



Standard Resistance:
Tester Connection Condition Specified Condition
a3-1 (CBI) - Body ground and shield ground Ignition switch off 10 MΩ or higher
a3-2 (CEI) - Body ground and shield ground Ignition switch off 10 MΩ or higher


HINT:

Visually inspect the HV floor under wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

34.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

27.CHECK FLOOR UNDER WIRE
34.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A458490

Connect the HV floor under wire connector to the inverter with converter assembly.


Procedure1

c.
A458491C02
2.229,1.042 2.115,1.042 2.115,1.042 1.938,1.271 true 2.271,0.979 2.521,1.167 0.25,0.188 10 true *a
*a High Voltage Terminal


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
High voltage terminal - Body ground Ignition switch off 1 MΩ or higher


HINT:

Perform this inspection with the motor cable and air conditioning wire disconnected from the inverter with converter assembly.



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

4.CHECK HV BATTERY (HIGH VOLTAGE CABLE)

NG

23.REPLACE INVERTER WITH CONVERTER ASSEMBLY
35.CHECK MOTOR CABLE (FOR MG2)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the motor cable from the hybrid vehicle transaxle assembly.

HINT:

Click hereDrivetrain>P910 (HYBRID TRANSMISSION / TRANSAXLE)>MOTOR CABLE>REMOVAL



Procedure1

c.
A377530C54
1.51,0.188 1.927,0.448 0.417,0.26 2.729,1.542 2.938,1.792 false 0.99,1.063 0.813,1.854 true 1.406,1.042 1.406,1.865 true 1.688,1.031 1.938,1.885 true 3.01,1.75 3.219,1.927 0.208,0.177 10 false *1 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.646,0.25 1.958,0.448 0.313,0.198 10 false k2 0.75,1.906 1.063,2.104 0.313,0.198 10 false W 1.375,1.917 1.615,2.125 0.24,0.208 10 false U 1.927,1.917 2.167,2.125 0.24,0.208 10 false V
*1 Shield Ground
*a Motor Cable (for MG2)
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
k2-2 (U) - Shield ground Ignition switch off 10 MΩ or higher
k2-3 (V) - Shield ground Ignition switch off 10 MΩ or higher
k2-1 (W) - Shield ground Ignition switch off 10 MΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

19.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

20.REPLACE MOTOR CABLE
36.CHECK MOTOR CABLE (FOR MG1)
CAUTION:

Be sure to wear insulated gloves.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the motor cable from the hybrid vehicle transaxle assembly.

HINT:

Click hereDrivetrain>P910 (HYBRID TRANSMISSION / TRANSAXLE)>MOTOR CABLE>REMOVAL



Procedure1

c.
A377530C56
1.573,0.198 1.948,0.427 0.375,0.229 2.177,1.042 2.177,1.885 true 2.448,1.063 2.708,1.875 true 1.917,1.052 1.615,1.885 true 2.75,1.531 2.99,1.76 false 3.031,1.719 3.344,1.917 0.313,0.198 10 false *1 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 2.146,1.917 2.458,2.115 0.313,0.198 10 false U 2.698,1.917 3.01,2.115 0.313,0.198 10 false V 1.563,1.917 1.875,2.115 0.313,0.198 10 false W 1.698,0.25 2.01,0.448 0.313,0.198 10 false k2
*1 Shield Ground
*a Motor Cable (for MG1)
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
k2-5 (U) - Shield ground Ignition switch off 10 MΩ or higher
k2-6 (V) - Shield ground Ignition switch off 10 MΩ or higher
k2-4 (W) - Shield ground Ignition switch off 10 MΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

19.REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

20.REPLACE MOTOR CABLE