Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420053 HYBRID BATTERY SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  ECU Power Source Circuit  


DESCRIPTION

If the ignition switch to ON, the battery ECU assembly applies current to the MREL terminal to turn the IGCT-MAIN relay on. This supplies power to the IGCT terminals.

WIRING DIAGRAM

A460029E03
0.24,0.74 1.969,1 1.729,0.26 10 false from IGCT-MAIN Relay 2.542,0.917 3.406,1.188 0.865,0.271 10 false IGCT NO. 2 4.771,0.698 5.208,0.938 0.438,0.24 10 false IGCT 4.792,1.552 5.281,1.865 0.49,0.313 10 false GND 4.448,2.198 6.438,2.469 1.99,0.271 10 false Battery ECU Assembly 4.51,1.479 4.854,1.76 0.344,0.281 10 false 34 4.51,0.604 4.865,0.885 0.354,0.281 10 false 24 2.625,0.594 2.969,0.875 0.344,0.281 10 false 1 3.063,0.594 3.406,0.813 0.344,0.219 10 false 2 4.448,2.031 4.792,2.313 0.344,0.281 10 false z12

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK BATTERY ECU ASSEMBLY (IGCT VOLTAGE)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL


c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the ignition switch to ON.


f.
A459571C08
1.49,0.115 1.948,0.427 0.458,0.313 2.583,2.875 2.281,2.115 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 2.49,2.917 2.948,3.135 0.458,0.219 10 false IGCT
*a Front view of wire harness connector
(Battery ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z12-24 (IGCT) - Body ground Ignition switch ON 11 to 14 V


NOTICE:
·

Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

If the ignition switch is turned to ON with the connectors disconnected, other DTCs will be stored. Be sure to clear the DTCs after the inspection.




g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the z12 battery ECU assembly connector.


j.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BODY GROUND)

NG

3.CHECK FUSE (IGCT NO. 2)
2.CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - BODY GROUND)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL


c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A459571C09
1.49,0.115 1.948,0.427 0.458,0.313 2.375,2.875 2.073,2.219 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.615,0.198 2.073,0.396 0.458,0.198 10 false z12 2.26,2.917 2.698,3.115 0.438,0.198 10 false GND
*a Front view of wire harness connector
(to Battery ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z12-34 (GND) - Body ground Always Below 1 Ω



e.

Reconnect the z12 battery ECU assembly connector.


f.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FUSE (IGCT NO. 2)
a.
A459865C01
2.167,0.969 2.646,0.781 true 0.177,0.094 0.49,0.292 0.313,0.198 10 false *1 2.708,0.708 3.021,0.906 0.313,0.198 10 false *2
*1 No. 5 Relay Block Assembly
*2 IGCT NO. 2 Fuse


Remove the IGCT NO. 2 fuse from the No. 5 relay block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IGCT NO. 2 fuse Always Below 1 Ω



c.

Install the IGCT NO. 2 fuse to the No. 5 relay block assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATTERY ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATTERY ECU ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL


c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A459865C01
2.167,0.969 2.646,0.781 true 0.177,0.094 0.49,0.292 0.313,0.198 10 false *1 2.708,0.708 3.021,0.906 0.313,0.198 10 false *2
*1 No. 5 Relay Block Assembly
*2 IGCT NO. 2 Fuse


Remove the IGCT NO. 2 fuse from the No. 5 relay block assembly.


e.

Measure the resistance according to the value(s) in the table below.

A459866C01
4.938,0.177 5.323,0.5 0.385,0.323 5.844,2.396 5.604,1.781 true 0.427,0.094 0.74,0.292 0.313,0.198 10 false *1 2.042,0.531 2.354,0.729 0.313,0.198 10 false *2 3.969,0.24 4.281,0.438 0.313,0.198 10 false *a 5.031,0.271 5.49,0.469 0.458,0.198 10 false z12 5.75,2.438 6.208,2.635 0.458,0.198 10 false IGCT
*1 No. 5 Relay Block Assembly *2 IGCT NO. 2 Fuse Holder
*a Front view of wire harness connector
(to Battery ECU Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
z12-24 (IGCT) - 2 (IGCT NO. 2 fuse holder) Always Below 1 Ω



f.

Install the IGCT NO. 2 fuse to the No. 5 relay block assembly.


g.

Reconnect the z12 battery ECU assembly connector.


h.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IGCT-MAIN RELAY - IGCT NO. 2 FUSE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (IGCT-MAIN RELAY - IGCT NO. 2 FUSE)
a.
A460020C01
2.167,0.969 2.615,0.875 true 1.99,2.573 2.583,2.438 true 0.167,0.094 0.479,0.292 0.313,0.198 10 false *1 2.677,0.802 2.99,1 0.313,0.198 10 false *2 2.667,2.354 2.979,2.552 0.313,0.198 10 false *3
*1 No. 5 Relay Block Assembly
*2 IGCT NO. 2 Fuse
*3 IGCT-MAIN Relay


Remove the IGCT NO. 2 fuse and IGCT-MAIN relay from the No. 5 relay block assembly.


b.
A460021C01
0.177,0.083 0.49,0.281 0.313,0.198 10 false *1 2.042,0.635 2.354,0.833 0.313,0.198 10 false *2 2.083,2 2.396,2.198 0.313,0.198 10 false *3
*1 No. 5 Relay Block Assembly
*2 IGCT NO. 2 Fuse Holder
*3 IGCT-MAIN Relay Holder


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (IGCT-MAIN relay holder) - 1 (IGCT NO. 2 fuse holder) Always Below 1 Ω



c.

Install the IGCT NO. 2 fuse and IGCT-MAIN relay to the No. 5 relay block assembly.


Result:
Proceed to
OK
NG



OK

CHECK ECU Power Source Circuit (HYBRID CONTROL SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGCT NO. 2 FUSE - BATTERY ECU ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL


c.
A458604N01
0.938,0.229 1.313,0.448 0.375,0.219 0.979,0.24 1.281,0.417 0.302,0.177 10 true z12

Disconnect the z12 battery ECU assembly connector.

NOTICE:

Before disconnecting the connector, check that it is not loose or disconnected.



d.
A459865C01
2.167,0.969 2.646,0.781 true 0.177,0.094 0.49,0.292 0.313,0.198 10 false *1 2.708,0.708 3.021,0.906 0.313,0.198 10 false *2
*1 No. 5 Relay Block Assembly
*2 IGCT NO. 2 Fuse


Remove the IGCT-NO. 2 fuse from the No. 5 relay block assembly.


e.

Measure the resistance according to the value(s) in the table below.

A459866C01
4.938,0.177 5.323,0.5 0.385,0.323 5.844,2.396 5.604,1.781 true 0.427,0.094 0.74,0.292 0.313,0.198 10 false *1 2.042,0.531 2.354,0.729 0.313,0.198 10 false *2 3.969,0.24 4.281,0.438 0.313,0.198 10 false *a 5.031,0.271 5.49,0.469 0.458,0.198 10 false z12 5.75,2.438 6.208,2.635 0.458,0.198 10 false IGCT
*1 No. 5 Relay Block Assembly *2 IGCT NO. 2 Fuse Holder
*a Front view of wire harness connector
(to Battery ECU Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
z12-24 (IGCT) or 2 (IGCT NO. 2 fuse holder) - Body ground and other terminals Always Below 1 Ω



f.

Install the IGCT NO. 2 fuse to the No. 5 relay block assembly.


g.

Reconnect the z12 battery ECU assembly connector.


h.

Install the No. 1 HV battery hose.


Result:
Proceed to
OK
NG



OK

REPLACE FUSE (IGCT NO. 2)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

REPLACE FUSE (IGCT NO. 2)