Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › OIL COOLER › 2020.03–2020.07
RM36W0E _52 Drivetrain _088636 P910 HYBRID TRANSMISSION / TRANSAXLE _0421992 OIL COOLER A

P910 HYBRID TRANSMISSION / TRANSAXLE  OIL COOLER  INSTALLATION  


PROCEDURE

Hide G1271C 1.INSTALL NO. 1 MOTOR COOLING HOSE

HINT:

Perform this procedure only when replacement of the motor cooling cooler is necessary.


a.
C429468C01
0,0 0,0 false
V100155

ATF Application Area


Coat a small amount of ATF as shown in the illustration.


b.
C429469C01
2.073,0.969 1.917,0.698 1.917,0.698 2.25,0.948 true 1.198,1.292 1.448,1.427 true 2.427,0.344 2.74,0.5 0.313,0.156 10 false *a 2.542,1.469 2.854,1.625 0.313,0.156 10 false *b 1.75,0.552 2.063,0.708 0.313,0.156 10 false *c 1.5,0.906 1.698,1.063 0.198,0.156 10 true *d 1.51,1.365 1.823,1.521 0.313,0.156 10 false *e
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Center of Paint Mark
*e 180°
V100145

Claw of Clip Location


Install the No. 1 motor cooling hose to the motor cooling cooler and slide the clip to secure it.

NOTICE:
·

Be careful not to deform the motor cooling cooler.

·

Make sure to align the paint mark on the No. 1 motor cooling hose with the paint mark on the motor cooling cooler.

·

Make sure that the claws of the clip are positioned within the area shown in the illustration.




Hide G1272C 2.INSTALL NO. 2 MOTOR COOLING HOSE

HINT:

Perform this procedure only when replacement of the motor cooling cooler is necessary.


a.
C429471C01
0,0 0,0 false
V100155

ATF Application Area


Coat a small amount of ATF as shown in the illustration.


b.
C429472C01
2.083,0.958 1.938,0.625 1.938,0.625 2.24,0.958 true 1.208,1.271 1.417,1.396 true 2.427,0.344 2.74,0.5 0.313,0.156 10 false *a 2.521,1.479 2.833,1.635 0.313,0.156 10 false *b 1.781,0.458 2.094,0.615 0.313,0.156 10 false *c 1.479,0.906 1.688,1.042 0.208,0.135 10 true *d 1.458,1.344 1.771,1.5 0.313,0.156 10 false *e
*a 0 to 3 mm (0 to 0.118 in.)
*b 2 to 7 mm (0.0787 to 0.276 in.)
*c Paint Mark
*d Center of Paint Mark
*e 180°
V100145

Claw of Clip Location


Install the No. 2 motor cooling hose to the motor cooling cooler and slide the clip to secure it.

NOTICE:
·

Be careful not to deform the motor cooling cooler.

·

Make sure to align the paint mark on the No. 2 motor cooling hose with the paint mark on the motor cooling cooler.

·

Make sure that the claws of the clip are positioned within the area shown in the illustration.




Hide G125A 3.INSTALL MOTOR COOLING COOLER

a.
C429462C01
1.052,0.083 1.646,0.281 0.594,0.198 10 true 1 (*a), 4 2.406,1.677 2.583,1.865 0.177,0.188 10 true 2 0.75,1.677 0.927,1.865 0.177,0.188 10 true 3
*a Temporarily Tighten


Temporarily install the motor cooling cooler to the hybrid vehicle transaxle assembly with the 3 bolts.


b.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.
C429474C01
2.688,1.375 2.354,1.271 2.354,1.271 2.688,1.271 true 3.115,1.677 3.406,1.854 0.292,0.177 10 false *a 2.146,1.167 2.458,1.323 0.313,0.156 10 false *b
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b Paint Mark


Install the No. 2 motor cooling pipe to the No. 2 motor cooling hose and slide the clip to secure it.

NOTICE:

Make sure to align the paint mark on the No. 2 motor cooling pipe with the paint mark on the No. 2 motor cooling hose.



d.

Temporarily install the No. 2 motor cooling pipe to the hybrid vehicle transaxle assembly with the oil cooler union bolt and a new gasket.


e.

Engage the clamp.


f.

Tighten the oil cooler union bolt to install the No. 2 motor cooling pipe.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


g.
C406269C03
2.688,0.771 2.302,0.604 2.302,0.604 2.667,0.604 true 3.083,1.052 3.26,1.219 0.177,0.167 10 false *a 2.146,0.542 2.458,0.698 0.313,0.156 10 false *b
*a 2 to 7 mm (0.0787 to 0.276 in.)
*b Paint Mark


Connect the No. 1 motor cooling hose to the No. 1 motor cooling pipe and slide the clip to secure it.

NOTICE:

Make sure to align the paint mark on the No. 1 motor cooling pipe with the paint mark on the No. 1 motor cooling hose.



Hide G922F 4.CONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

Hide G922H 5.CONNECT INLET HYBRID RADIATOR HOSE

Hide G9200 6.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 8.INSPECT FOR HYBRID TRANSAXLE FLUID LEAK

Hide 51442C 9.INSTALL ENGINE UNDER COVER LH

Hide 51451A 10.INSTALL CENTER ENGINE UNDER COVER