Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for Gasoline Model) › 2020.03–2020.07
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0422047 BRAKE BOOSTER(for Gasoline Model) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for Gasoline Model)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the master cylinder sub-assembly from the brake booster assembly.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 47201 1.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 55606 3.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 5.LOOSEN CLEVIS LOCK NUT

a.
C142634C01
1.948,1.146 1.75,1.667 1.75,1.667 1.5,1.667 false 2.365,1.135 2.781,1.135 true 1.323,1.604 1.635,1.76 0.313,0.156 10 *1 2.833,1.073 3.146,1.229 0.313,0.156 10 *2
*1 Clevis Lock Nut
*2 Brake Master Cylinder Push Rod Clevis


Loosen the clevis lock nut of the brake master cylinder push rod clevis.


Hide 47101A 6.REMOVE BRAKE PEDAL RETURN SPRING

Hide 51451A 8.REMOVE CENTER ENGINE UNDER COVER

Hide 55225C 9.REMOVE DASH PANEL HEAT INSULATOR

a.
C429873

Remove the 3 nuts and dash panel heat insulator.


Hide 10.SEPARATE BRAKE LINE

a.
C429016

Using a union nut wrench, disconnect the front No. 1 brake tube and front No. 2 brake tube from the brake actuator assembly.


b.

Disengage the 10 clamps to remove the 2 No. 5 brake tube clamps from the brake lines.


c.

for Manual Transaxle:

i.
C435050

Disengage the clamp to separate the clutch master cylinder to flexible hose tube from the No. 2 brake tube clamp.



d.
C432450

Disengage the 3 clamps to separate the brake lines from the No. 2 brake tube clamp.


e.
C432451

Disengage the clamp to remove the No. 2 brake tube clamp from the vehicle body.


f.
C432452

Disengage the 6 clamps to remove the 2 No. 1 brake tube clamps from the brake lines.


Hide 11.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

a.
C435052

Slide the clip and disconnect the check valve to connector tube hose from the brake booster assembly.


Hide 44610 12.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C435053

Disconnect the connector.


b.
C435051C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the vehicle body.


c.
C435054

Remove the 4 nuts.


d.

Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.


e.
C435055

Move aside the front No. 1 brake tube and front No. 2 brake tube as shown in the illustration.

NOTICE:

Do not apply excessive force to the brake tubes.



f.

Remove the brake booster assembly.


Hide 44785 13.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the brake booster assembly.