Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0424496 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air conditioner unit assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
·

No. 1 air conditioning radiator damper servo sub-assembly

·

Air conditioning amplifier assembly


Initialize servo motor (Air Conditioning System) DTCs are stored for HV Model:
(Click here)
for Gasoline Model:
(Click here)

PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 51451A 2.REMOVE CENTER ENGINE UNDER COVER

Hide 3.DRAIN ENGINE COOLANT

Hide 4.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55735A 5.REMOVE WATER GUARD PLATE LH

a.
I116308

Disengage the claws to remove the water guard plate LH.


Hide 55815E 6.REMOVE NO. 1 FRONT VENTILATOR SEAL

a.
I116309

Disengage the claws to remove the No. 1 front ventilator seal.


Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

a.
I116310

Disengage the clamp.


b.

Remove the 12 bolts and outer cowl top panel sub-assembly.

I116311


Hide 88707 8.DISCONNECT SUCTION PIPE SUB-ASSEMBLY

a.
I115659

Remove the bolt.


b.
I115660

Rotate the hook connector and disconnect the suction pipe sub-assembly as shown in the illustration.


c.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88716A 9.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A

a.
I115661

Disconnect the cooler refrigerant liquid pipe A.


b.

Remove the O-ring from the cooler refrigerant liquid pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 16290F 10.DISCONNECT NO. 3 WATER BY-PASS HOSE ASSEMBLY

a.
I115663

Slide the hose clip to disconnect the No. 3 water by-pass hose assembly.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the No. 3 water by-pass hose assembly and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the No. 3 water by-pass hose assembly.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245 11.DISCONNECT INLET HEATER WATER HOSE

a.
I115664

Slide the hose clip to disconnect the inlet heater water hose.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the inlet heater water hose and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the inlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87211 13.REMOVE NO. 1 AIR DUCT

a.
I116312

Remove the 2 bolts.


b.

Disengage the claws to remove the No. 1 air duct.


Hide 14.REMOVE STEERING COLUMN ASSEMBLY

Hide 55086A 15.REMOVE CENTER HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I115666

Remove the clip.


b.

Disengage the clamp to remove the center heater to register duct sub-assembly.


Hide 55084E 16.REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116313

Remove the clip.


b.

Disengage the clamp to remove the No. 1 heater to register duct sub-assembly.


Hide 55085 17.REMOVE NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
I116314

Remove the clip.


b.

Disengage the clamp to remove the No. 2 heater to register duct sub-assembly.


Hide 18.REMOVE FRONT SEAT ASSEMBLY RH

Hide 19.REMOVE FRONT SEAT ASSEMBLY LH

HINT:

HINT:Use the same procedure as for the RH side.


Hide 58510D 20.SEPARATE FRONT FLOOR CARPET ASSEMBLY

a.

Remove the 2 clips to turn back the front floor carpet assembly as shown in the illustration.

I116315


Hide 55216C 21.REMOVE NO. 4 DASH PANEL INSULATOR PAD

a.

Disengage the clips to remove the No. 4 dash panel insulator pad.

I116316


Hide 88539J 22.DISCONNECT DRAIN COOLER HOSE

a.
I115675

Disconnect the drain cooler hose.


Hide 83108 23.REMOVE METER MIRROR SUB-ASSEMBLY (w/ Headup Display)

Hide 24.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

Hide 55306A 25.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
I116317

Remove the bolt to disconnect the wire harness.


b.

Disengage the clamps to disconnect the wire harness.


c.

Remove the bolt, screw, nut and No.1 instrument panel brace sub-assembly.


Hide 82141 26.SEPARATE INSTRUMENT PANEL WIRE

a.
I115677

Disengage the clamps.


b.
I115680

Remove the 2 nuts to separate the instrument panel junction block assembly RH.


c.

for Manual Air Conditioning System:

i.
I115683

Disconnect the 2 connectors.


ii.

Disengage the clamps.



d.

for Automatic Air Conditioning System:

i.
I115682

Disconnect the connector.


ii.

Disengage the clamp.



e.

for Manual Air Conditioning System:

i.
I115686

Disconnect the connector.


ii.

Disengage the clamp.



f.

for Automatic Air Conditioning System:

i.
I116396

Disconnect the 2 connectors.


ii.

Disengage the clamp.



g.

Disconnect each connector.

I116318


h.

Remove the 4 bolts to disconnect the 4 ground wires.


i.

Disengage clamps to separate the instrument panel wire.


Hide 27.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the nut and 6 bolts.

I116099C01
0,0 0,0 false
V113147

Remove in this Direction - -



b.

Disengage the guides to remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.


Hide 28.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and air conditioner unit assembly.

I116100