Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › CAMSHAFT
RM36W0E _51 Engine / Hybrid System _089412 M15A-FXE ENGINE MECHANICAL _0424634 CAMSHAFT A

M15A-FXE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during camshaft removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of ignition coil assembly

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Gas leak from exhaust system is repaired

·

Replacement of cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Removal and installation of a camshaft timing gear assembly


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL

CAUTION:
·
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If an SRS part is accidentally deployed, it may cause a serious injury.



Hide 12262 2.DISCONNECT NO. 2 VENTILATION HOSE

a.
A466839

Disconnect the No. 2 ventilation hose from the cylinder head cover sub-assembly.


Hide 82121 3.REMOVE ENGINE WIRE

a.
A466842

Disconnect the 4 connectors.


b.

Disconnect the clamp.


c.

Remove the 5 bolts.


d.
A466840

Disconnect the connector.


e.

Disconnect the 2 clamps.


f.
A466841

Disconnect the clamp.


g.

Remove the bolt.


Hide 11102A 5.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 7.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 135A0B 8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

Hide 13090D 9.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 11201 10.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 11.REMOVE SPARK PLUG TUBE GASKET

Hide 12.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.
A466050C02
2.406,0.656 2.635,0.24 2.635,0.24 2.823,0.24 true 2.458,0.969 2.792,1.094 2.792,1.094 2.927,1.094 true 2.479,0.781 2.76,0.531 2.76,0.531 2.969,0.531 true 0.656,0.448 0.854,0.448 0.854,0.448 1.021,0.708 true 0.552,1.5 0.552,1.26 0.552,1.26 0.906,0.896 true 1.792,2.677 1.594,2.677 1.594,2.677 1.302,2.677 true 0.667,2.781 0.823,2.781 0.823,2.781 1.365,2.969 true 1.427,1.354 1.271,1.354 1.271,1.354 1.042,1 true 0.458,1.521 0.656,1.719 0.198,0.198 10 true *a 0.406,2.677 0.604,2.885 0.198,0.208 10 true *b 1.833,2.583 2.042,2.792 0.208,0.208 10 true *c 1.479,1.26 1.677,1.469 0.198,0.208 10 true *b 0.406,0.333 0.604,0.542 0.198,0.208 10 true *b 3.021,0.469 3.219,0.667 0.198,0.198 10 true *a 2.979,1 3.177,1.208 0.198,0.208 10 true *b 2.854,0.146 3.052,0.354 0.198,0.208 10 true *b
*a Paint Mark
*b Timing Mark
*c "0" Timing Mark


Turn the crankshaft clockwise to align the timing mark (cutout) on the crankshaft pulley with the "0" timing mark on the No. 2 timing chain cover assembly.


b.

Check that the timing marks are positioned as shown in the illustration.

HINT:

If the timing marks are not positioned as shown in the illustration, turn the crankshaft clockwise and then align them again.



c.

Place paint marks on the timing chain sub-assembly at points aligned with the timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly.


Hide 13.REMOVE STRAIGHT SCREW PLUG

Hide 14.REMOVE CAMSHAFT

a.
A466051C01
1.365,0 1.573,0.167 0.208,0.167 10 true *a
*a Approximately 15°


Rotate the crankshaft approximately 15° clockwise.


b.
A466052C01
1.375,0 1.594,0.198 0.219,0.198 10 true *a
*a Approximately 15°


Rotate the crankshaft approximately 15° counterclockwise.


c.
A466053C01
1.635,0.417 1.917,0.417 true 1.365,3.031 1.51,3.031 1.51,3.031 1.74,3.448 true 1.979,0.323 2.177,0.531 0.198,0.208 10 true *a 1.125,2.917 1.323,3.125 0.198,0.208 10 true *b
*a Pin
*b Pin Hole (No. 1 Chain Tensioner Assembly Side)


Insert the pin to the No. 1 chain tensioner assembly pin hole.


d.
A466054C01
3.115,0.125 3.323,0.323 0.208,0.198 10 true *a
*a Hold


Using the hexagonal portion of the exhaust camshaft sub-assembly, secure the exhaust camshaft sub-assembly.

NOTICE:

Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.



e.

Remove the 2 bolts from the camshaft timing exhaust gear assembly.


f.
A466055C01
2.375,0.083 2.563,0.281 0.188,0.198 10 true *a
*a Hold
V113147

Turn


Using the hexagonal portion of the intake camshaft sub-assembly, secure the intake camshaft sub-assembly.

NOTICE:
·

Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.

·

Do not disassemble the camshaft timing gear assembly.




g.

Using a bi-hexagon socket wrench (10 mm), remove the bolt from the camshaft timing gear assembly.


h.

Using the hexagonal portion of the exhaust camshaft sub-assembly, loosen and hold the timing chain sub-assembly while moving the exhaust camshaft sub-assembly in the direction shown in the illustration.

A460248C01
5.5,0.01 5.698,0.229 0.198,0.219 10 false *a
*a Hold - -
V113147

Turn - -



i.

Move the camshaft timing gear assembly together with the camshaft timing exhaust gear assembly and timing chain sub-assembly toward the No. 2 timing chain cover assembly as shown in the illustration.

A466057C01
2.115,1.385 2.427,1.385 true 2.583,0.698 2.927,0.135 2.927,0.135 3.125,0.135 true 2.635,2.146 2.854,2.635 2.854,2.635 3.052,2.635 true 3.146,0.063 3.333,0.26 0.188,0.198 10 false *1 3.094,2.563 3.281,2.76 0.188,0.198 10 false *2 1.865,1.292 2.052,1.49 0.188,0.198 10 true *3
*1 Camshaft Timing Gear Assembly *2 Camshaft Timing Exhaust Gear Assembly
*3 Timing Chain Sub-assembly - -
V113147

Remove in this Direction - -



j.

Remove the camshaft timing exhaust gear assembly from the timing chain sub-assembly.


k.

Remove the camshaft timing gear assembly from the timing chain sub-assembly.


l.
A466058

Secure the timing chain sub-assembly to the vehicle using rope, etc.

NOTICE:

Do not drop the timing chain sub-assembly into the timing chain cover assembly.



m.
A466059N01
1.073,1.563 1.229,1.76 0.156,0.198 10 true 1 3.094,0.823 3.25,1.021 0.156,0.198 10 true 2 2.958,1.948 3.115,2.146 0.156,0.198 10 true 3 1.729,0.5 1.885,0.698 0.156,0.198 10 true 4 1.719,1.583 1.875,1.781 0.156,0.198 10 true 5 2.438,0.51 2.573,0.688 0.135,0.177 10 true 6 2.365,1.552 2.5,1.719 0.135,0.167 10 true 7

Uniformly loosen and remove the 7 camshaft bearing cap bolts in the order shown in the illustration.


n.
A466060C01
0.396,0.76 0.677,0.76 true 1.521,0.771 1.688,0.771 true 1.677,1.313 1.677,1.177 1.677,1.177 2.01,1.031 true 2.427,0.813 2.594,0.813 true 0.146,0.677 0.354,0.865 0.208,0.188 10 true *1 1.74,0.667 1.938,0.854 0.198,0.188 10 true *2 2.198,0.729 2.396,0.917 0.198,0.188 10 true *4 1.771,0.042 2,0.24 0.229,0.198 10 true 10 1.781,1.958 1.979,2.167 0.198,0.208 10 true 11 2.927,1.458 3.083,1.656 0.156,0.198 10 true 7 3.25,0.604 3.396,0.802 0.146,0.198 10 true 4 1.198,1.969 1.354,2.177 0.156,0.208 10 true 2 3.24,1.188 3.427,1.417 0.188,0.229 10 true 5 2.448,0.073 2.604,0.229 0.156,0.156 10 true 8 2.948,0.042 3.104,0.24 0.156,0.198 10 true 6 2.438,1.948 2.583,2.156 0.146,0.208 10 true 9 1.125,1.427 1.292,1.635 0.167,0.208 10 true 3 1.188,0.042 1.333,0.24 0.146,0.198 10 true 1 1.625,1.365 1.833,1.552 0.208,0.188 10 true *3
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap
*4 No. 4 Camshaft Bearing Cap


Uniformly loosen and remove the 11 camshaft bearing cap bolts in the order shown in the illustration.

NOTICE:

Uniformly loosen the camshaft bearing cap bolts while holding the camshaft horizontally.



o.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

HINT:

Arrange the removed parts so that they can be reinstalled in their original locations.



p.
A466061

Remove the intake camshaft sub-assembly from the camshaft housing sub-assembly.


q.
A466062

Remove the exhaust camshaft sub-assembly from the camshaft housing sub-assembly.