Home › Drivetrain › CLUTCH › CLUTCH MASTER CYLINDER › 2020.03–2020.07
RM36W0E _52 Drivetrain _089426 CLUTCH _0424692 CLUTCH MASTER CYLINDER A

CLUTCH  CLUTCH MASTER CYLINDER  INSTALLATION  


PROCEDURE

Hide 31410 1.INSTALL CLUTCH MASTER CYLINDER ASSEMBLY

a.

Install a new clutch master cylinder gasket to the clutch master cylinder assembly.


b.

Install the clutch master cylinder assembly to the vehicle body with the 2 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 31453A 2.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

Hide 55606 4.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 31481 5.CONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE

a.
C431519C01
1.74,2.99 2.052,3.188 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the clutch master cylinder to flexible hose tube to the clutch master cylinder assembly.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the clutch master cylinder to flexible hose tube.

·

Do not allow any foreign matter such as dirt or dust to enter the clutch master cylinder to flexible hose tube from the connecting part.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 31434E 6.CONNECT NO. 1 CLUTCH RESERVOIR HOSE

a.
C431521C01
0.073,2.229 3.365,3.26 3.292,1.031 1.073,2.615 1.323,2.385 1.323,2.385 1.458,2.385 true 0.156,2.292 0.469,2.51 0.313,0.219 10 false *a 0.938,2.208 1.25,2.406 0.313,0.198 10 false *b 1.49,2.281 1.792,2.479 0.302,0.198 10 false *c 2.802,2.521 3.135,2.771 0.333,0.25 10 false *d 1.042,1.385 1.26,1.594 0.219,0.208 10 true A
*a View A
*b Top of Vehicle
*c Paint Mark (Top of Vehicle)
*d 0 to 2 mm (0 to 0.0787 in.)


Connect the No. 1 clutch reservoir hose to the clutch master cylinder assembly and slide the hose clip to secure it.

NOTICE:
·

Make sure that the paint mark of the No. 1 clutch reservoir hose is within the location shown in the illustration.

·

Make sure that the claws of the hose clip are within the location shown in the illustration.




Hide 7.BLEED CLUTCH LINE

Hide 8.INSPECT FOR BRAKE FLUID LEAK

Hide 55701J 10.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55815E 12.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 13.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 14.INSPECT CLUTCH PEDAL