The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit has a short circuit, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.
For the circuit diagram of the ECM power source refer to the ECM power source circuit.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>ECM Power Source Circuit
VC Output Circuit
Check the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
| *1 | No. 1 Engine Room Relay Block |
| *2 | EFI NO. 1 Fuse |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (EFI NO. 1 fuse) - Body ground | Ignition switch ON | 11 to 14 V |
Check the fuse with it installed to the No. 1 engine room relay block.
If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the D18 throttle body with motor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>THROTTLE BODY>REMOVAL
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Disconnect the A62 accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the e4 crankshaft position sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the D7 camshaft position sensor (for intake camshaft) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the D20 manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the D8 camshaft position sensor (for exhaust camshaft) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the D32 engine oil pressure and temperature sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the e2 fuel pressure sensor (for high pressure side) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL PRESSURE SENSOR (for High Pressure)>REMOVAL
Perform "Inspection After Repair" after replacing the fuel pressure sensor (for high pressure side).
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Disconnect the D27 fuel pressure sensor (for low pressure side) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible (w/ Gasoline Particulate Filter) | A |
| Communication is not possible (w/o Gasoline Particulate Filter) | B |
| Communication is possible | C |
A
B
C
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL PRESSURE SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the fuel pressure sensor (for low pressure side).
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Disconnect the D66 differential pressure sensor connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the D23 mass air flow meter sub-assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible (for continuously variable transaxle models) | A |
| Communication is not possible (for manual transaxle models) | B |
| Communication is possible | C |
A
B
C
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Disconnect the D44 neutral position switch connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the D18 throttle body with motor assembly connector.
Disconnect the e4 crankshaft position sensor connector.
Disconnect the D7 camshaft position sensor (for intake camshaft) connector.
Disconnect the D8 camshaft position sensor (for exhaust camshaft) connector.
Disconnect the D20 manifold absolute pressure sensor connector.
Disconnect the D32 engine oil pressure and temperature sensor connector.
Disconnect the A62 accelerator pedal sensor assembly connector.
Disconnect the D23 mass air flow meter sub-assembly connector.
Disconnect the e2 fuel pressure sensor (for high pressure side) connector.
Disconnect the D27 fuel pressure sensor (for low pressure side) connector.
Disconnect the D44 neutral position switch connector (w/o stop and start system for manual transaxle models).
Disconnect the D66 differential pressure sensor connector. (w/ Gasoline Particulate Filter)
Disconnect the D51 and A54 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D51-109 (VCTA) - Body ground | Always | 10 kΩ or higher |
| D51-116 (VCNE) - Body ground | Always | 10 kΩ or higher |
| D51-88 (VCV1) - Body ground | Always | 10 kΩ or higher |
| D51-113 (VCE1) - Body ground | Always | 10 kΩ or higher |
| D51-121 (VCPM) - Body ground | Always | 10 kΩ or higher |
| D51-99 (VCPE) - Body ground | Always | 10 kΩ or higher |
| A54-57 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A54-60 (VCP2) - Body ground | Always | 10 kΩ or higher |
| D51-78 (VCVG) - Body ground | Always | 10 kΩ or higher |
| D51-98 (VCPR) - Body ground | Always | 10 kΩ or higher |
| D51-84 (VCPF) - Body ground | Always | 10 kΩ or higher |
| D51-83 (VCNP)*1 - Body ground | Always | 10 kΩ or higher |
| D51-82 (VCPX)*2 - Body ground | Always | 10 kΩ or higher |
| A54-9 (+B) - 1 (EFI NO. 2 fuse) | Always | Below 1 Ω |
| A54-35 (+B2) - 1 (EFI NO. 2 fuse) | Always | Below 1 Ω |
*1: w/o stop and start system for manual transaxle models
*2: w/ Gasoline Particulate Filter
| Proceed to |
|---|
| OK |
| NG |
OK
NG