Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _087499 M15A-FKS ENGINE CONTROL _0418534 SFI SYSTEM J

M15A-FKS ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch assembly*3 or clutch start switch assembly*4 and to terminal STA of the ECM (STA signal).

*1: w/o Entry and Start System

*2: w/ Entry and Start System

*3: for Continuously Variable Transaxle Models

*4: for Manual Transaxle Models

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH STOP AND START SYSTEM
a.

Confirm the vehicle specifications.

Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B




A

2.CHECK WHETHER ENGINE CAN BE CRANKED

B

19.CHECK WHETHER ENGINE CAN BE CRANKED
2.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

3.READ VALUE USING GTS (STARTER SW)

B

18.READ VALUE USING GTS (STARTER SW)
3.READ VALUE USING GTS (STARTER SW)
a.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


b.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Result Proceed to
NG (for Continuously Variable Transaxle Models) A
NG (for Manual Transaxle Models) B
OK C



A

4.CHECK STOP AND START SYSTEM

B

11.CHECK STOP AND START SYSTEM

C

33.INSPECT ST NO. 1 RELAY
4.CHECK STOP AND START SYSTEM

Result:
Result
OK
NG



OK

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR STOP AND START SYSTEM

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>PARK / NEUTRAL POSITION SWITCH>INSPECTION

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

6.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

8.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the D45 park/neutral position switch assembly connector.


b.

Disconnect the A67 engine stop and start ECU connector.


c.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


d.

Disconnect the A54 ECM connector.


e.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D45-5 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A67-21 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA), A67-21 (STA), 2 (ST NO. 1 relay), D45-5 (L) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D45 park/neutral position switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the A67 engine stop and start ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - D45-4 (B) Always Below 1 Ω
H45-10 (STAR) - A54-23 (NSW) Always Below 1 Ω
H45-10 (STAR) - A67-17 (CLL) Always Below 1 Ω
H45-10 (STAR), D45-4 (B), A54-23 (NSW) or A67-17 (CLL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the D45 park/neutral position switch assembly connector.


b.

Disconnect the A67 engine stop and start ECU connector.


c.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


d.

Disconnect the A54 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D45-5 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A67-21 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
D45-5 (L), A67-21 (STA), 2 (ST NO. 1 relay) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)
a.

Disconnect the H54 ignition switch assembly connector.


b.

Disconnect the D45 park/neutral position switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the A67 engine stop and start ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - D45-4 (B) Always Below 1 Ω
H54-4 (ST2) - A54-23 (NSW) Always Below 1 Ω
H54-4 (ST2) - A67-17 (CLL) Always Below 1 Ω
H54-4 (ST2), A67-17 (CLL), D45-4 (B) or A54-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT IGNITION SWITCH ASSEMBLY

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

11.CHECK STOP AND START SYSTEM

Result:
Result
OK
NG



OK

12.INSPECT CLUTCH START SWITCH ASSEMBLY

NG

REPAIR STOP AND START SYSTEM

12.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

13.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

15.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE CLUTCH START SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the A54 ECM connector.


c.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


d.

Disconnect the A64 clutch start switch assembly connector.


e.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A67-21 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA), 2 (ST NO. 1 relay), A64-1 (L) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM - ENGINE STOP AND START ECU)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A64 clutch start switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the A67 engine stop and start ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - A64-2 (B) Always Below 1 Ω
H45-10 (STAR) - A67-17 (CLL) Always Below 1 Ω
A67-17 (CLL) - A54-23 (NSW) Always Below 1 Ω
H45-10 (STAR), A67-17 (CLL), A54-23 (NSW) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the A54 ECM connector.


c.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


d.

Disconnect the A64 clutch start switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A67-21 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A64-1 (L), 2 (ST NO. 1 relay), A67-21 (STA) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the H54 ignition switch assembly connector.


b.

Disconnect the A64 clutch start switch assembly connector.


c.

Disconnect the A67 engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - A64-2 (B) Always Below 1 Ω
H54-4 (ST2) - A67-17 (CLL) Always Below 1 Ω
H54-4 (ST2) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>M15A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

18.READ VALUE USING GTS (STARTER SW)
a.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


b.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Result Proceed to
OK A
NG (for Continuously Variable Transaxle Models) B
NG (for Manual Transaxle Models) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 2 RELAY - ECM)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)

19.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

20.READ VALUE USING GTS (STARTER SW)

B

41.READ VALUE USING GTS (STARTER SW)
20.READ VALUE USING GTS (STARTER SW)
a.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


b.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Result Proceed to
NG (for Continuously Variable Transaxle Models) A
NG (for Manual Transaxle Models) B
OK C



A

21.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

27.INSPECT CLUTCH START SWITCH ASSEMBLY

C

33.INSPECT ST NO. 1 RELAY
21.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>PARK / NEUTRAL POSITION SWITCH>INSPECTION

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

22.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

24.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

22.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the D45 park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D45-5 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA), 2 (ST NO. 1 relay), D45-5 (L) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D45 park/neutral position switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - D45-4 (B) Always Below 1 Ω
H45-10 (STAR) - A54-23 (NSW) Always Below 1 Ω
H45-10 (STAR), D45-4 (B) or A54-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the D45 park/neutral position switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


c.

Disconnect the A54 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D45-5 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
D45-5 (L), 2 (ST NO. 1 relay) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM)
a.

Disconnect the H54 ignition switch assembly connector.


b.

Disconnect the D45 park/neutral position switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - D45-4 (B) Always Below 1 Ω
H54-4 (ST2) - A54-23 (NSW) Always Below 1 Ω
H54-4 (ST2), D45-4 (B) or A54-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

26.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.INSPECT IGNITION SWITCH ASSEMBLY

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

27.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

28.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

30.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE CLUTCH START SWITCH ASSEMBLY

28.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the A64 clutch start switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA), 2 (ST NO. 1 relay), A64-1 (L) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A64 clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - A64-2 (B) Always Below 1 Ω
H45-10 (STAR) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the A64 clutch start switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


c.

Disconnect the A54 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A54-30 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A64-1 (L), 2 (ST NO. 1 relay) or A54-30 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

31.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the H54 ignition switch assembly connector.


b.

Disconnect the A64 clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - A64-2 (B) Always Below 1 Ω
H54-4 (ST2) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

32.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>M15A-FKS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION SWITCH ASSEMBLY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

33.INSPECT ST NO. 1 RELAY

OK

34.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 1 RELAY

34.INSPECT STARTER ASSEMBLY

Result:
Proceed to
OK
NG



OK

35.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

35.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


b.

Disconnect the D54 starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay) - D54-1 (ST) Always Below 1 Ω
3 (ST NO. 1 relay) or D54-1 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

36.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the D80 starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - D80-1 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

37.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A457773C03
0.115,0.125 0.427,0.281 0.313,0.156 10 false *1 2.063,2.333 2.375,2.49 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST NO. 1 Relay


a.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

38.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 1 RELAY)

38.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for Continuously Variable Transaxle Models) A
OK (for Manual Transaxle Models) B
NG C



A

39.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

B

40.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


b.

Disconnect the D45 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST NO. 1 relay) - D45-5 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block.


b.

Disconnect the A64 clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST NO. 1 relay) - A64-1 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.READ VALUE USING GTS (STARTER SW)
a.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


b.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11
OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)