Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
48259A
1.INSTALL REAR UPPER COIL SPRING INSULATOR
| *a | Fit |
Install the rear upper coil spring insulator to the rear coil spring.
Install the rear upper coil spring insulator so that the dimension between the stopper and upper end of the rear coil spring is 10 mm (0.394 in.) or less.
The identification mark of the rear coil spring should be towards the underside.
48258C
2.INSTALL REAR LOWER COIL SPRING INSULATOR
| *a | Fit |
Install the rear lower coil spring insulator to the rear axle beam assembly.
Securely insert the protrusion of the rear lower coil spring insulator into the guide holes of the rear axle beam assembly.
48231B
3.INSTALL REAR COIL SPRING
Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.
Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.
Because the nuts have their own stoppers, do not turn the nuts. Loosen the bolts with the nuts secured.
Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks.
|
Identification Mark |
Set the rear coil spring to the rear axle beam assembly.
Make sure that there is no gap between the coil end of the rear coil spring and the stopper of the rear lower coil spring insulator.
Set the rear coil spring so that the identification mark is positioned as shown in the illustration.
Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks and temporarily install the rear shock absorber assemblies LH and RH with the 2 bolts and 2 nuts.
| *a | Wooden Block | *b | Jack |
Because the nuts have their own stoppers, do not turn the nuts. Tighten the bolts with the nuts secured.
Insert the bolt with the threaded end facing the outside of the vehicle.
46430
4.CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY
Install the No. 3 parking brake cable assembly to the rear axle beam assembly with the nut.
46420
5.CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY
Perform the same procedure as for the No. 3 side.
47319F
6.INSTALL REAR FLEXIBLE HOSE LH
| *a | Torque Wrench Fulcrum Length |
Install the rear flexible hose LH to the rear axle beam assembly with a new clip.
Install the clip as far as it will go.
Using a union nut wrench 10 mm, connect the brake tube to the rear flexible hose while holding the rear flexible hose with a wrench.
Do not kink or damage the brake line.
Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
47318F
7.INSTALL REAR FLEXIBLE HOSE RH
Perform the same procedure as for the LH side.
89516D
8.INSTALL SKID CONTROL SENSOR WIRE LH
Install the skid control sensor wire LH to the rear axle beam assembly with the 2 nuts.
Do not twist the skid control sensor wire when installing it.
Connect the skid control sensor wire LH connector.
89516C
9.INSTALL SKID CONTROL SENSOR WIRE RH
Perform the same procedure as for the LH side.
10.BLEED BRAKE LINE
for HV Model:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model TMC Made)>BLEEDING
for Gasoline Model:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for Gasoline Model)>BLEEDING
11.INSTALL REAR WHEEL
12. STABILIZE SUSPENSION
42110F
13.FULLY TIGHTEN REAR AXLE BEAM ASSEMBLY
48540
14.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH
48760B
15.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH
Perform the same procedure as for the LH side.
16.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)
17.CHECK FOR SPEED SENSOR SIGNAL
18.INSPECT REAR WHEEL ALIGNMENT
19. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (for HV Model)
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART