Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE FLUID (for Gasoline Model) › 2020.07–2020.09
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0422042 BRAKE FLUID(for Gasoline Model) N

BRAKE SYSTEM (OTHER)  BRAKE FLUID(for Gasoline Model)  BLEEDING  


CAUTION / NOTICE / HINT

NOTICE:
·

Move the shift lever to P and apply the parking brake before bleeding the brakes.

·

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

·

If brake fluid leaks onto any painted surface, immediately wash it off.

·

Do not operate the brake actuator assembly while air is in the brake system or in the brake master cylinder sub-assembly. Doing so may cause air to enter the brake actuator assembly.

·

If bleeding the brake actuator assembly is difficult due to air in the brake actuator assembly, replace it with a new one.

·

When bleeding air, select the suitable procedure listed below.

Replaced/Installed Item Work Procedure
Flexible hose (front/rear) Bleed brake line
Front disc brake cylinder assembly
Rear wheel cylinder assembly
Brake actuator assembly Bleed brake system
Brake master cylinder sub-assembly
Brake master cylinder reservoir sub-assembly
Brake booster assembly



HINT:

If any work is performed on the brake system or if air in the brake lines is suspected, bleed the air from the brake system.


PROCEDURE

Hide 1.BLEED BRAKE LINE (for LHD)

a.

Remove the center cowl top ventilator louver.

i.
C436674

Disengage the 2 clips and hook to separate the hood to cowl top seal.


ii.
C436675

Disengage the 2 claws and 5 guides to remove the center cowl top ventilator louver from the cowl top ventilator louver sub-assembly.



b.
C436683

Remove the brake master cylinder reservoir filler cap assembly.


c.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT 3

SAE J1704 or FMVSS No. 116 DOT 4


NOTICE:
·

Make sure that there is sufficient brake fluid in the reservoir.

·

Do not remove the filter from the brake master cylinder reservoir assembly and be sure to fill the brake master cylinder reservoir assembly with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.




d.

Remove the bleeder plug cap.


e.

Connect a vinyl tube to the bleeder plug.


f.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


g.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2


h.

Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.


i.

Tighten the bleeder plug completely.

Torque:
Front brake : 17 N*m (173 kgf*cm, 13 ft.*lbf)
Rear brake : 9.5 N*m (97 kgf*cm, 84 in.*lbf)


j.

Install the bleeder plug cap.


k.

Repeat the above steps to bleed the brake fluid of the brake lines for each wheel.


l.

Inspect for brake fluid leaks.


m.

Inspect the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for Gasoline Model)>ON-VEHICLE INSPECTION


n.

Install the brake master cylinder reservoir filler cap assembly.


o.

Install the center cowl top ventilator louver.

i.

Engage the 5 guides and 2 claws to install the center cowl top ventilator louver to the cowl top ventilator louver sub-assembly.


ii.

Engage the 2 clips and hook to install the hood to cowl top seal.



Hide 2.BLEED BRAKE LINE (for RHD)

a.

Remove the center cowl top ventilator louver.

i.
C430390

Disengage the 2 clips and hook to separate the hood to cowl top seal.


ii.
C430391

Disengage the 2 claws and 5 guides to remove the center cowl top ventilator louver from the cowl top ventilator louver sub-assembly.



b.
C436684C01
0.083,0.083 0.385,0.333 0.302,0.25 12 true *A 0.083,2.75 0.385,3 0.302,0.25 12 true *B
*A for TMC Made
*B for TMMF Made


Remove the brake master cylinder reservoir filler cap assembly.


c.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT 3

SAE J1704 or FMVSS No. 116 DOT 4


NOTICE:
·

Make sure that there is sufficient brake fluid in the reservoir.

·

Do not remove the filter from the brake master cylinder reservoir and be sure to fill the brake master cylinder reservoir with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.




d.

Remove the bleeder plug cap.


e.

Connect a vinyl tube to the bleeder plug.


f.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


g.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2


h.

Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.


i.

Tighten the bleeder plug completely.

Torque:
Front brake (for TMC Made) : 8.3 N*m (85 kgf*cm, 73 in.*lbf)
Front brake (for TMMF Made) : 17 N*m (173 kgf*cm, 13 ft.*lbf)
Rear brake (for TMC Made) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Rear brake (for TMMF Made) : 9.5 N*m (97 kgf*cm, 84 in.*lbf)


j.

Install the bleeder plug cap.


k.

Repeat the above steps to bleed the brake fluid of the brake lines for each wheel.


l.

Inspect for brake fluid leaks.


m.

Inspect the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for Gasoline Model)>ON-VEHICLE INSPECTION


n.

Install the brake master cylinder reservoir filler cap assembly.


o.

Install the center cowl top ventilator louver.

i.

Engage the 5 guides and 2 claws to install the center cowl top ventilator louver to the cowl top ventilator louver sub-assembly.


ii.

Engage the 2 clips and hook to install the hood to cowl top seal.



Hide 3.BLEED BRAKE SYSTEM (for LHD)

CAUTION:
C427793

If air is bleed without using the GTS, damage or accidents may result. Therefore, always use the GTS when bleeding air.


NOTICE:
·

To prevent brake fluid from damaging painted surfaces, cover any surrounding parts with a piece of cloth.

·

Be sure to clean your hands before bleeding the master cylinder to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.



a.

Remove the windshield wiper motor and link assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL




d.

Remove the outer cowl top panel sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for LHD)>REMOVAL


e.
C436683

Remove the brake master cylinder reservoir filler cap assembly.


f.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT 3

SAE J1704 or FMVSS No. 116 DOT 4


NOTICE:
·

Make sure that there is sufficient brake fluid in the reservoir.

·

Do not remove the filter from the brake master cylinder reservoir and be sure to fill the brake master cylinder reservoir with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.




g.
C436685

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




h.
C436686

Slowly depress the brake pedal and hold it.*1


i.
C436687

Cover the 2 outer holes with fingers and release the brake pedal.*2


j.

Repeat steps *1 and *2, 3 or 4 times.


k.
C436688C01
1.771,2.948 2.083,3.104 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




l.

Remove the bleeder plug cap.


m.

Connect a vinyl tube to the bleeder plug.


n.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


o.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2


p.

Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.


q.

Tighten the bleeder plug completely.

Torque:
Front brake : 17 N*m (173 kgf*cm, 13 ft.*lbf)
Rear brake : 9.5 N*m (97 kgf*cm, 84 in.*lbf)


r.

Install the bleeder plug cap.


s.

Repeat the above steps to bleed the brake fluid of the brake lines for each wheel.


t.

Depress the brake pedal more than 20 times with the ignition switch off.


u.

Bleed the brake system following the instructions on the GTS.

Chassis > Brake > Utility
Tester Display
Air Bleeding
50005 435 4636
NOTICE:

Do not start the engine.



v.

After air bleeding, tighten each bleeder plug while depressing the brake pedal.

Torque:
Front brake : 17 N*m (173 kgf*cm, 13 ft.*lbf)
Rear brake : 9.5 N*m (97 kgf*cm, 84 in.*lbf)


w.

Inspect for brake fluid leaks.


x.

Inspect the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for Gasoline Model)>ON-VEHICLE INSPECTION


y.

Install the brake master cylinder reservoir filler cap assembly.


z.

Install the outer cowl top panel sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for LHD)>INSTALLATION




ac.

Install the windshield wiper motor and link assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION


Hide 4.BLEED BRAKE SYSTEM (for RHD)

CAUTION:
C427793

If air is bleed without using the GTS, damage or accidents may result. Therefore, always use the GTS when bleeding air.


NOTICE:
·

To prevent brake fluid from damaging painted surfaces, cover any surrounding parts with a piece of cloth.

·

Be sure to clean your hands before bleeding the master cylinder to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.



a.

Remove the windshield wiper motor and link assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL




d.

Remove the outer cowl top panel sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for RHD)>REMOVAL


e.
C436684C01
0.083,0.083 0.385,0.333 0.302,0.25 12 true *A 0.083,2.75 0.385,3 0.302,0.25 12 true *B
*A for TMC Made
*B for TMMF Made


Remove the brake master cylinder reservoir filler cap assembly.


f.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

Brake Fluid:

SAE J1703 or FMVSS No. 116 DOT 3

SAE J1704 or FMVSS No. 116 DOT 4


NOTICE:
·

Make sure that there is sufficient brake fluid in the reservoir.

·

Do not remove the filter from the brake master cylinder reservoir and be sure to fill the brake master cylinder reservoir with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.




g.
C429562

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




h.
C429563

Slowly depress the brake pedal and hold it.*1


i.
C429564

Cover the 2 outer holes with fingers and release the brake pedal.*2


j.

Repeat steps *1 and *2, 3 or 4 times.


k.
C429565C01
1.76,3 2.073,3.156 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




l.

Remove the bleeder plug cap.


m.

Connect a vinyl tube to the bleeder plug.


n.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


o.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.*2


p.

Repeat steps *1 and *2 until all the air in the brake fluid is completely bled out and new brake fluid comes out.


q.

Tighten the bleeder plug completely.

Torque:
Front brake (for TMC Made) : 8.3 N*m (85 kgf*cm, 73 in.*lbf)
Front brake (for TMMF Made) : 17 N*m (173 kgf*cm, 13 ft.*lbf)
Rear brake (for TMC Made) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Rear brake (for TMMF Made) : 9.5 N*m (97 kgf*cm, 84 in.*lbf)


r.

Install the bleeder plug cap.


s.

Repeat the above steps to bleed the brake fluid of the brake lines for each wheel.


t.

Depress the brake pedal more than 20 times with the ignition switch off.


u.

Bleed the brake system following the instructions on the GTS.

Chassis > Brake > Utility
Tester Display
Air Bleeding
50005 435 6114
NOTICE:

Do not start the engine.



v.

After air bleeding, tighten each bleeder plug while depressing the brake pedal.

Torque:
Front brake (for TMC Made) : 8.3 N*m (85 kgf*cm, 73 in.*lbf)
Front brake (for TMMF Made) : 17 N*m (173 kgf*cm, 13 ft.*lbf)
Rear brake (for TMC Made) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Rear brake (for TMMF Made) : 9.5 N*m (97 kgf*cm, 84 in.*lbf)


w.

Inspect for brake fluid leaks.


x.

Inspect the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for Gasoline Model)>ON-VEHICLE INSPECTION


y.

Install the brake master cylinder reservoir filler cap assembly.


z.

Install the outer cowl top panel sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for RHD)>INSTALLATION




ac.

Install the windshield wiper motor and link assembly.

Click hereVehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION