Home › Engine / Hybrid System › 1KR-FE (ENGINE MECHANICAL) › ENGINE › from 2020.07
RM36W0E _51 Engine / Hybrid System _091035 1KR-FE ENGINE MECHANICAL _0431323 ENGINE G

1KR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Separate the air cleaner cap sub-assembly.

Click hereGeneral>MAINTENANCE>1KR-FE AIR CLEANER FILTER ELEMENT>REMOVAL


b.

Remove the air cleaner filter element sub-assembly.


c.

Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily.

If necessary, replace the air cleaner filter element sub-assembly.

HINT:
·

If there is any foreign matter or clogs in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any foreign matter or clogs remain even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




d.

Install the air cleaner filter element sub-assembly.


e.

Install the air cleaner cap sub-assembly.

Click hereGeneral>MAINTENANCE>1KR-FE AIR CLEANER FILTER ELEMENT>INSTALLATION


Hide 7.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29
Standard Ignition Timing:

-10.5 to 15 degrees BTDC


NOTICE:
·

Check the ignition timing with the cooling fan off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




v.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 234 13 29

vi.

Monitor IGN Advance of the Data List.

Standard Ignition Timing:

8 to 12 degrees BTDC


NOTICE:

When checking the ignition timing, the transaxle should be in neutral or park.



vii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / OFF.


viii.

Check that the ignition timing advances immediately when the engine speed is increased.


ix.

Turn the ignition switch off.


x.

Disconnect the GTS from the DLC3.



Hide 8.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

v.

Inspect the engine idle speed.

Standard Idle Speed:

790 to 890 rpm


NOTICE:
·

Turn off all electrical systems and the A/C.

·

Inspect the engine idle speed with the cooling fan off.

·

When checking the engine idle speed, the transaxle should be in neutral or park.




vi.

Turn the ignition switch off.


vii.

Disconnect the GTS from the DLC3.



Hide 9.INSPECT COMPRESSION

NOTICE:

Keep the spark plug holes free of foreign matter when measuring the compression pressure.



b.

Warm up and stop the engine.



d.

Disconnect the 3 fuel injector connectors.

NOTICE:

Disable fuel injection in order to prevent catalyst damage due to unburned gasoline.



e.
A421758

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Standard Compression Pressure:

1550 kPa (15.8 kgf/cm2, 225 psi)


Minimum Compression Pressure:

1160 kPa (11.9 kgf/cm2, 168 psi)


Pressure Difference between Each Cylinder:

147 kPa (1.5 kgf/cm2, 21 psi) or less


NOTICE:
·

Use a fully-charged battery to obtain an engine speed of 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




iv.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole, then inspect it again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the gasket.





f.

Connect the 3 fuel injector connectors.



h.

Clear the DTCs.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



Hide 10.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Keep the engine speed at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe during idle.


d.

Check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

HINT:

When doing a 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Possible Cause
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect timing

-

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle body assembly

-

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty SFI systems:

-

Pressure regulator

-

Engine coolant temperature sensor

-

Mass air flow meter

-

ECM

-

Fuel injector assemblies

-

Throttle body assembly