Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P040311  Exhaust Gas Recirculation "A" Circuit Short to Ground  P040312  Exhaust Gas Recirculation "A" Circuit Short to Battery  P040313  Exhaust Gas Recirculation "A" Circuit Open  


DESCRIPTION

Refer to DTC P040000.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P040000

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P040311 Exhaust Gas Recirculation "A" Circuit Short to Ground Open or short to ground in EGR valve circuit (3 trip detection logic).
·

Open or short in EGR valve circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored Engine A
P040312 Exhaust Gas Recirculation "A" Circuit Short to Battery Short to power source circuit in EGR valve (1 trip detection logic).
·

Open or short in EGR valve circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored Engine A
P040313 Exhaust Gas Recirculation "A" Circuit Open Open in EGR valve circuit (3 trip detection logic)
·

Open or short in EGR valve circuit

·

EGR valve assembly

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

DTC P040311, P040312 and P040313 are stored while the engine is in fuel cut condition for 4 seconds or more and the brake pedal is pressed for approximately 2 seconds.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in Neutral position.

·

The A/C switch and all accessory switches should be off.




Procedure1

b.

Confirm that Throttle Position is ON and check the engine idling condition and the value of Intake Manifold Absolute Pressure in the Data List while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
EGR Step Position
50004 372 25 385,386
HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 20 steps or more during Active Test.



OK:

Intake Manifold Absolute Pressure and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 20 Steps
Idling condition Steady idling Idling changes from steady to rough idling
Intake Manifold Absolute Pressure value
(Data List)
29 to 37 kPa
(EGR valve is fully closed)
Intake Manifold Absolute Pressure value is at least +10 kPa higher than when EGR valve is fully closed


HINT:

During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in EGR valve.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

NG

2.INSPECT EGR VALVE ASSEMBLY
2.INSPECT EGR VALVE ASSEMBLY

OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)

Pre-procedure1

a.

Disconnect the EGR valve assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D76-5 (+B1) - Body ground Ignition switch ON 11 to 14 V
D76-2 (+B2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - EFI-MAIN NO. 1 RELAY)
4.CHECK HARNESS AND CONNECTOR (ECM - EGR VALVE ASSEMBLY)

Pre-procedure1

a.

Disconnect the ECM connector.


b.

Disconnect the EGR valve assembly connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D76-4 (EGR1) - D50-29 (EGR1) Always Below 1 Ω
D76-3 (EGR2) - D50-28 (EGR2) Always Below 1 Ω
D76-6 (EGR3) - D50-59 (EGR3) Always Below 1 Ω
D76-1 (EGR4) - D50-58 (EGR4) Always Below 1 Ω
D76-4 (EGR1) or D50-29 (EGR1) - Body ground Always 10 kΩ or higher
D76-3 (EGR2) or D50-28 (EGR2) - Body ground Always 10 kΩ or higher
D76-6 (EGR3) or D50-59 (EGR3) - Body ground Always 10 kΩ or higher
D76-1 (EGR4) or D50-58 (EGR4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - EFI-MAIN NO. 1 RELAY)

Pre-procedure1

a.

Disconnect the EGR valve assembly connector.


b.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1) - D76-5 (+B1) Always Below 1 Ω
5 (EFI-MAIN NO. 1) - D76-2 (+B2) Always Below 1 Ω
5 (EFI-MAIN NO. 1) or D76-5 (+B1) - Body ground Always 10 kΩ or higher
5 (EFI-MAIN NO. 1) or D76-2 (+B2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR