Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P040000  Exhaust Gas Recirculation "A" Flow  


DESCRIPTION

The EGR (Exhaust Gas Recirculation) system recirculates exhaust gases, which are controlled to the proper volume in accordance with driving conditions. The recirculated gas mingles with the intake air, therefore slowing down the engine combustion and lowering the combustion temperature. This helps reduce nitrogen oxide (NOx) emissions.

In order to increase circulation, the ECM adjusts the lift of the EGR valve and intake shutter valve (throttle valve).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P040000 Exhaust Gas Recirculation "A" Flow Target and actual manifold absolute pressure rates differ (3 trip detection logic).
·

Open or short in EGR valve circuit

·

EGR valve assembly

·

EGR passage

·

Intake manifold

·

ECM


Comes on DTC stored Engine B

HINT:

If DTC P040311, P040312 or P040313 has already been stored, P040000 is not stored.


WIRING DIAGRAM

A459176E01
5.479,0.531 5.76,0.74 0.281,0.208 10 false A55 1.323,2.063 2.292,2.292 0.969,0.229 10 false EFI-MAIN NO.1 0.604,3.365 1.615,3.604 1.01,0.24 10 false EFI-MAIN NO.1 0.594,4.24 1.698,4.469 1.104,0.229 10 false BATT-MAIN NO.1 0.76,4.938 1.406,5.156 0.646,0.219 10 false Battery 4.302,1.792 4.458,1.99 0.156,0.198 10 false 4 4.302,2.198 4.458,2.396 0.156,0.198 10 false 3 4.302,2.604 4.458,2.802 0.156,0.198 10 false 6 4.292,3.01 4.448,3.208 0.156,0.198 10 false 1 4.302,3.354 4.458,3.552 0.156,0.198 10 false 2 4.292,3.677 4.448,3.875 0.156,0.198 10 false 5 3.865,1.781 4.427,2 0.563,0.219 10 false EGR1 3.844,2.188 4.406,2.406 0.563,0.219 10 false EGR2 3.844,2.604 4.406,2.823 0.563,0.219 10 false EGR3 3.854,3.01 4.417,3.229 0.563,0.219 10 false EGR4 3.927,3.354 4.49,3.573 0.563,0.219 10 false +B2 3.927,3.677 4.49,3.896 0.563,0.219 10 false +B1 2.729,4.167 3.031,4.375 0.302,0.208 10 false D76 2.823,4.323 4.24,4.521 1.417,0.198 10 false EGR Valve Assembly 5.563,0.323 5.719,0.521 0.156,0.198 10 false 2 5.458,0.917 5.74,1.115 0.281,0.198 10 false A55 5.49,1.875 5.76,2.073 0.271,0.198 10 false D50 5.49,2.281 5.76,2.479 0.271,0.198 10 false D50 5.49,2.708 5.76,2.906 0.271,0.198 10 false D50 5.49,3.104 5.76,3.302 0.271,0.198 10 false D50 5.563,0.74 5.719,0.938 0.156,0.198 10 false 1 5.531,1.688 5.781,1.896 0.25,0.208 10 false 29 5.531,2.115 5.781,2.323 0.25,0.208 10 false 28 5.531,2.51 5.771,2.708 0.24,0.198 10 false 59 5.521,2.917 5.771,3.125 0.25,0.208 10 false 58 5.469,4.844 5.74,5.063 0.271,0.219 10 false A55 5.833,0.531 6.083,0.74 0.25,0.208 10 false +B 5.833,0.938 6.083,1.146 0.25,0.208 10 false +B1 5.844,1.854 6.24,2.052 0.396,0.198 10 false EGR1 5.833,2.271 6.229,2.469 0.396,0.198 10 false EGR2 5.833,2.698 6.229,2.896 0.396,0.198 10 false EGR3 5.823,3.094 6.219,3.292 0.396,0.198 10 false EGR4 5.833,4.833 6.229,5.031 0.396,0.198 10 false MREL 5.563,4.635 5.958,4.833 0.396,0.198 10 false 9 6.188,5.365 6.615,5.573 0.427,0.208 10 false ECM 3.531,1.313 4.76,1.51 1.229,0.198 10 false EFI NO.3 0.406,2.49 0.563,2.688 0.156,0.198 10 false 3 0.375,1.677 0.531,1.875 0.156,0.198 10 false 5 1.115,2.51 1.271,2.708 0.156,0.198 10 false 2 1.146,1.677 1.302,1.875 0.156,0.198 10 false 1

CONFIRMATION DRIVING PATTERN

DTC P040000 is stored while the engine is in fuel cut condition for 4 seconds or more and the brake pedal is pressed for approximately 2 seconds.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTC OUTPUT (IN ADDITION TO DTC P040000)
a.

Read the DTC.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P040000 is output A
P040000, P040311, P040312 or P040313 is output B




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:
·

When performing the Active Test, make sure the shift lever is in Neutral position.

·

The A/C switch and all accessory switches should be off.




Procedure1

b.

Confirm that Throttle Position is ON and check the engine idling condition and the value of Intake Manifold Absolute Pressure in the Data List while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
EGR Step Position
50004 372 25 385,386
HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 20 steps or more during Active Test.



OK:

Intake manifold absolute pressure and idling condition change in response to EGR step position as follows.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 20 Steps
Idling condition Steady idling Idling changes from steady to rough idling or engine stalls
Intake Manifold Absolute Pressure value
(Data List)
29 to 37 kPa
(EGR valve is fully closed)
Intake Manifold Absolute Pressure value is at least +10 to 15 kPa higher than when EGR valve is fully closed


HINT:

During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in EGR valve.


EGR Valve is Sticking in Close Side:
- EGR Step Position (Active Test)
0 Steps 20 Steps
Idling condition Steady idling Steady idling


EGR Valve is Sticking in Open Side:
- EGR Step Position (Active Test)
0 Steps 20 Steps
Idling condition Rough idling or engine stall
(Engine difficult to start)
Rough idling or engine stall
(Engine difficult to start)



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

3.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM - EFI-MAIN NO. 1 RELAY)

NG

9.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
3.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM - EFI-MAIN NO. 1 RELAY)

Pre-procedure1

a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D76-4 (EGR1) - D50-29 (EGR1) Always Below 1 Ω
D76-3 (EGR2) - D50-28 (EGR2) Always Below 1 Ω
D76-6 (EGR3) - D50-59 (EGR3) Always Below 1 Ω
D76-1 (EGR4) - D50-58 (EGR4) Always Below 1 Ω
5 (EFI-MAIN NO. 1) - D76-5 (+B1) Always Below 1 Ω
5 (EFI-MAIN NO. 1) - D76-2 (+B2) Always Below 1 Ω
D76-4 (EGR1) or D50-29 (EGR1) - Body ground Always 10 kΩ or higher
D76-3 (EGR2) or D50-28 (EGR2) - Body ground Always 10 kΩ or higher
D76-6 (EGR3) or D50-59 (EGR3) - Body ground Always 10 kΩ or higher
D76-1 (EGR4) or D50-58 (EGR4) - Body ground Always 10 kΩ or higher
D76-5 (+B1) or D76-2 (+B2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

e.

None.



OK

4.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



b.

Drive the vehicle at 60 to 80 km/h (37 mph to 50 mph) with the shift lever in the 3rd position.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



c.

Perform fuel-cut operation for 4 seconds or more, with the accelerator pedal fully released and the brake pedal pressed.

HINT:

If the vehicle speed becomes lower than 40 km/h (25 mph) within 4 seconds, perform the confirmation driving pattern again.



Procedure1

d.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P040000 is output A
DTCs are not output B



Post-procedure1

e.

None.



A

6.REPLACE EGR VALVE ASSEMBLY

B

6.REPLACE EGR VALVE ASSEMBLY

NEXT

7.CLEAR DTC
7.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



b.

Drive the vehicle at 60 to 80 km/h (37 mph to 50 mph) with the shift lever in the 3rd position.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



c.

Perform fuel-cut operation for 4 seconds or more, with the accelerator pedal fully released and the brake pedal pressed.

HINT:

If the vehicle speed becomes lower than 40 km/h (25 mph) within 4 seconds, perform the confirmation driving pattern again.



Procedure1

d.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P040000 is output A
DTCs are not output B



Post-procedure1

e.

None.



A

B

END

9.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

Pre-procedure1

a.

Warm up the engine.


Procedure1

b.

Read the Intake Manifold Absolute Pressure value at racing the engine.

Powertrain > Engine > Data List
Tester Display
Intake Manifold Absolute Pressure
50003 372 385
Standard:
Condition Specified Condition
Ignition switch ON 80 to 110 kPa
Racing the engine Changes in response to accelerator pedal operation



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

10.CHECK FOR DEPOSIT (EXHAUST MANIFOLD CONVERTER TO EGR VALVE ASSEMBLY)

NG

15.CHECK INTAKE SYSTEM
10.CHECK FOR DEPOSIT (EXHAUST MANIFOLD CONVERTER TO EGR VALVE ASSEMBLY)
a.

Check for cracks, damage, and clogs in the pipes between the exhaust manifold converter and the EGR valve assembly.


b.

Check for exhaust leaks at each connection point.

HINT:

This check may require the removal of components.


OK:

No deposit



Result:
Proceed to
OK
NG



OK

11.CHECK FOR DEPOSIT (EGR VALVE ASSEMBLY TO INTAKE PORT)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

11.CHECK FOR DEPOSIT (EGR VALVE ASSEMBLY TO INTAKE PORT)
a.

Check for cracks, damage, and clogs in the pipes between the intake port and the EGR valve assembly.


b.

Check for exhaust leaks at each connection point.

HINT:

This check may require the removal of components.


OK:

No deposit



Result:
Proceed to
OK
NG



OK

12.REPLACE EGR VALVE ASSEMBLY

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

12.REPLACE EGR VALVE ASSEMBLY

NEXT

13.CLEAR DTC
13.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P040000)

Pre-procedure1

a.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



b.

Drive the vehicle at 60 to 80 km/h (37 mph to 50 mph) with the shift lever in the 3rd position.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



c.

Perform fuel-cut operation for 4 seconds or more, with the accelerator pedal fully released and the brake pedal pressed.

HINT:

If the vehicle speed becomes lower than 40 km/h (25 mph) within 4 seconds, perform the confirmation driving pattern again.



Procedure1

d.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P040000 is output A
DTCs are not output B



Post-procedure1

e.

None.



A

B

END

15.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

HINT:

Click hereEngine / Hybrid System>1KR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION


OK:

No leaks in intake system.



b.

Check the intake manifold.

OK:

The intake manifold is not cracked.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE INTAKE SYSTEM