Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM J

1KR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

w/o Entry and Start System

While the engine is being cranked, current flows from terminal ST2 of the ignition or starter switch assembly to the clutch start switch assembly and also flows to terminal STA of the ECM (STA Signal). The ECM uses the STA signal to control the fuel injection and ignition timing when the engine starts.


w/ Entry and Start System

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to clutch start switch assembly and also flows to terminal STA of the ECM (STA signal).


WIRING DIAGRAM

A469786E01
5.979,0.542 6.438,0.74 0.458,0.198 10 false NEO 5.979,0.906 6.438,1.104 0.458,0.198 10 false STA 5.542,0.542 6,0.74 0.458,0.198 10 false A55 6.271,1.583 6.729,1.781 0.458,0.198 10 false ECM 5.677,0.354 5.99,0.552 0.313,0.198 10 false 44 5.677,0.75 5.99,0.948 0.313,0.198 10 false 46 1.198,0.542 1.51,0.74 0.313,0.198 10 false NE 1.49,0.448 1.802,0.646 0.313,0.198 10 false 10 1.135,1.292 1.594,1.49 0.458,0.198 10 false CLL 1.51,1.198 1.823,1.396 0.313,0.198 10 false 17 1.125,0.875 1.583,1.073 0.458,0.198 10 false STA 1.5,0.802 1.813,1 0.313,0.198 10 false 21 0.458,1.688 0.917,1.885 0.458,0.198 10 false A67 0.448,1.865 4.271,2.063 3.823,0.198 10 false Engine Stop and Start ECU*1 1.198,2.688 1.51,2.885 0.313,0.198 10 false NE 1.104,3.646 1.719,3.844 0.615,0.198 10 false STA 1.031,3.156 1.49,3.354 0.458,0.198 10 false STAR 1.5,2.594 1.813,2.792 0.313,0.198 10 false 15 1.51,3.052 1.76,3.271 0.25,0.219 10 false 10 1.521,3.542 1.677,3.74 0.156,0.198 10 false 3 3.906,3.979 4.219,4.177 0.313,0.198 10 false A64 3.896,4.156 5.792,4.385 1.896,0.229 10 false Clutch Start Switch Assembly 5.094,3.563 5.25,3.76 0.156,0.198 10 false 2 4.031,3.563 4.188,3.76 0.156,0.198 10 false 1 0.188,3.958 0.646,4.156 0.458,0.198 10 false H45 0.177,4.125 6.906,4.323 6.729,0.198 10 false Certification ECU (Smart Key ECU Assembly)*2 2.104,0.385 2.417,0.583 0.313,0.198 10 false *1 2.094,0.813 2.406,1.01 0.313,0.198 10 false *1 2.083,1.198 2.396,1.396 0.313,0.198 10 false *1 3.344,3.417 3.656,3.615 0.313,0.198 10 false *3 2.844,4.75 3,4.948 0.156,0.198 10 false 4 2.531,4.771 2.99,4.969 0.458,0.198 10 false ST2 1.927,4.76 2.385,4.958 0.458,0.198 10 false AM2 1.75,4.75 1.906,4.948 0.156,0.198 10 false 1 1.573,5.073 1.885,5.271 0.313,0.198 10 false H54 1.323,5.219 5.302,5.417 3.979,0.198 10 false Ignition or Starter Switch Assembly*3 0.99,5.031 1.448,5.229 0.458,0.198 10 false AM2 2.854,6.521 3.927,6.719 1.073,0.198 10 false ST NO. 1 4.688,5.875 5,6.073 0.313,0.198 10 false D54 4.677,7.177 4.99,7.375 0.313,0.198 10 false D80 4.854,5.688 5.01,5.885 0.156,0.198 10 false 1 4.802,6.969 4.958,7.167 0.156,0.198 10 false 1 4.99,7.625 6.24,7.885 1.25,0.26 10 false Starter Assembly 0.896,8.104 1.969,8.302 1.073,0.198 10 false Battery 1.813,7.875 3.729,8.094 1.917,0.219 10 false *2: w/ Entry and Start System 1.802,8.292 3.75,8.542 1.948,0.25 10 false *3: w/o Entry and Start System 2.698,5.76 2.854,5.958 0.156,0.198 10 false 5 3.469,5.74 3.625,5.938 0.156,0.198 10 false 3 2.677,6.094 2.833,6.292 0.156,0.198 10 false 1 3.479,6.135 3.635,6.333 0.156,0.198 10 false 2 0.677,5.396 1.24,5.75 0.563,0.354 10 false INP STD NO. 1-3 1.833,6.01 2.625,6.24 0.792,0.229 10 false ST NO. 1 5.104,7.177 5.417,7.375 0.313,0.198 10 false B 5.094,5.865 5.406,6.063 0.313,0.198 10 false ST 5.573,0.927 6.031,1.125 0.458,0.198 10 false A55 5.563,1.292 6.021,1.49 0.458,0.198 10 false D50 5.635,1.115 6.094,1.313 0.458,0.198 10 false 111 5.979,1.292 6.438,1.49 0.458,0.198 10 false NSW 2.083,2.573 2.396,2.771 0.313,0.198 10 false *2 2.063,3.052 2.375,3.25 0.313,0.198 10 false *2 2.052,3.552 2.365,3.75 0.313,0.198 10 false *2 4.219,3.573 4.375,3.771 0.156,0.198 10 false L 4.885,3.552 5.042,3.75 0.156,0.198 10 false B 0.865,6.01 1.677,6.354 0.813,0.344 10 false BATT- MAIN NO. 1 1.813,7.521 3.729,7.74 1.917,0.219 10 false *1: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK IF VEHICLE IS EQUIPPED WITH STOP AND START SYSTEM
a.

Confirm the vehicle specifications.

Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B




A

2.CHECK WHETHER ENGINE CAN BE CRANKED

B

11.CHECK WHETHER ENGINE CAN BE CRANKED
2.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

3.READ VALUE USING GTS (STARTER SW)

B

26.READ VALUE USING GTS (STARTER SW)
3.READ VALUE USING GTS (STARTER SW)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

b.

Fully depress the clutch pedal.


c.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

13.INSPECT ST NO. 1 RELAY

NG

4.CHECK STOP AND START SYSTEM
4.CHECK STOP AND START SYSTEM

OK

5.INSPECT CLUTCH START SWITCH ASSEMBLY

NG

REPAIR STOP AND START SYSTEM

5.INSPECT CLUTCH START SWITCH ASSEMBLY

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - CLUTCH START SWITCH ASSEMBLY - CERTIFICATION ECU - ST NO. 1 RELAY - ECM)

B

8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)

C

REPLACE CLUTCH START SWITCH ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - CLUTCH START SWITCH ASSEMBLY - CERTIFICATION ECU - ST NO. 1 RELAY - ECM)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


d.

Disconnect the clutch start switch assembly connector.


e.

Disconnect the certification ECU (smart key ECU assembly) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-21 (STA) - A55-46 (STA) Always Below 1 Ω
A67-21 (STA) - A64-1 (L) Always Below 1 Ω
A67-21 (STA), A55-46 (STA), H45-3 (STA), A64-1 (L) or 2 (ST NO. 1 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY - ECM)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the ECM connector.


e.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-10 (STAR) - A64-2 (B) Always Below 1 Ω
H45-10 (STAR) - A67-17 (CLL) Always Below 1 Ω
H45-10 (STAR) - D50-111 (NSW) Always Below 1 Ω
H45-10 (STAR), A64-2 (B), D50-111 (NSW) or A67-17 (CLL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM - ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the ECM connector.


c.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


d.

Disconnect the clutch start switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-21 (STA) - A55-46 (STA) Always Below 1 Ω
A67-21 (STA) - A64-1 (L) Always Below 1 Ω
A67-21 (STA), A55-46 (STA), A64-1 (L) or 2 (ST NO. 1 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ENGINE STOP AND START ECU - ST NO. 1 RELAY - ECM)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - A64-2 (B) Always Below 1 Ω
H54-4 (ST2) - A67-17 (CLL) Always Below 1 Ω
H54-4 (ST2) - D50-111 (NSW) Always Below 1 Ω
H54-4 (ST2), A67-17 (CLL), D50-111 (NSW) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>1KR-FE (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

11.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.

Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B




A

12.READ VALUE USING GTS (STARTER SW)

B

26.READ VALUE USING GTS (STARTER SW)
12.READ VALUE USING GTS (STARTER SW)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

b.

Fully depress the clutch pedal.


c.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

13.INSPECT ST NO. 1 RELAY

NG

20.INSPECT CLUTCH START SWITCH ASSEMBLY
13.INSPECT ST NO. 1 RELAY

OK

14.INSPECT STARTER ASSEMBLY

NG

REPLACE ST NO. 1 RELAY

14.INSPECT STARTER ASSEMBLY

OK

15.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)

NG

15.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - STARTER ASSEMBLY)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (ST NO. 1 relay) - D54-1 (ST) Always Below 1 Ω
3 (ST NO. 1 relay) or D54-1 (ST) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK TERMINAL VOLTAGE (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - D80-1 (B) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST NO. 1 RELAY)
A457773C06
0.104,0.104 0.417,0.302 0.313,0.198 10 false *1 2.063,2.344 2.375,2.542 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 ST NO. 1 Relay


a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST NO. 1 RELAY)

18.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - BODY GROUND)
a.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - CLUTCH START SWITCH ASSEMBLY)
a.

Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST NO. 1 relay) - A64-1 (L) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT CLUTCH START SWITCH ASSEMBLY

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION

Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG C



A

21.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

B

23.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

C

REPLACE CLUTCH START SWITCH ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - 2 (ST NO. 1 relay) Always Below 1 Ω
A55-46 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
H45-3 (STA), 2 (ST NO. 1 relay), A64-1 (L) or A55-46 (STA) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A45-10 (STAR) - A64-2 (B) Always Below 1 Ω
H45-10 (STAR) - D50-111 (NSW) Always Below 1 Ω
A45-10 (STAR), D50-111 (NSW) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the ignition or starter switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-46 (STA) - 2 (ST NO. 1 relay) Always Below 1 Ω
A55-46 (STA) or 2 (ST NO. 1 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (STA SIGNAL CIRCUIT)
a.

Disconnect the clutch start switch assembly connector.


b.

Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Disconnect the ignition or starter switch assembly connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H54-4 (ST2) - A64-2 (B) Always Below 1 Ω
H54-4 (ST2) - D50-111 (NSW) Always Below 1 Ω
H54-4 (ST2), D50-111 (NSW) or A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

25.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

26.READ VALUE USING GTS (STARTER SW)
a.

Enter the following menus.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

b.

Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).


c.

Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.

OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Engine started ON



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)